Vitreography is a fine art printmaking technique that uses a 3/8 inch thick
float glassmatrix instead of the traditional matrices of metal, wood or stone. A print created using the technique is called a vitreograph. Unlike a monotype, in which ink is painted onto a smooth glass plate and transferred to paper to produce a unique work, the vitreograph technique involves fixing the imagery in, or on, the glass plate. This allows the production of an editionof prints.
Advantages/Disadvantages of Vitreography
In addition to being relatively inexpensive, glass is chemically inert. It does not oxidize, nor does it change or interact with the composition of printing inks, especially yellows and whites, which can turn green or gray in contact with metal plates. [ Lidh, W. (1986) “Prints from Glass”, Introduction. Western Carolina University, Cullowhee, NC, ] According to Claire Van Vliet of Janus Press, intaglio vitreographs also have an advantage over metal in that the glass plate wipes cleanly in non-image areas, allowing bright white to coincide with “black that is velvety as a
mezzotint” in the finished print. [ McLean, G. (1999) “In Black and White: Landscape Prints by Claire Van Vliet”, page 61. Stinehour Press, Vermont]
Another advantage of vitreograph printmaking is its ability to withstand the pressure of the printing press with no discernible breakdown of the imagery, even after numerous runs. Printmaker Kenneth Kerslake wrote, “The glass plate will last indefinitely because, unlike [one of] copper or zinc, it will always return to its original configuration no matter how much pressure is applied.” [Kerslake(1998) “Vitreography: The Art and Technique of the Glass Print”, page 46. Glass Art, Vol. 13 No. 3 ] A disadvantage to this is that unwanted lines or marks on the glass plate cannot be burnished out, as they can on a zinc or copper plate. [Kessler, (1987) “Luminous Impressions: Prints from Glass Plates”, page 12. Mint Museum, Department of Art, Charlotte, NC]
The transparency of the glass plate can be used to advantage, in that the plate may be placed over a preliminary drawing on paper to guide the artist in creating a drawing on the plate. This is done by placing the drawing face down on a light table (to allow for the reversal of the image in printing) and placing the vitreograph plate on top of it. [Byrd, J. Falconer (1998) “Littreography”, page 15, special edition reprinted with permission of GLASS: the Urban Glass Quarterly, Number 72, Fall 1998] Although glass is unaffected by compression in the printing press, it will break under tension. For that reason, vitreographs are always printed on an etching press, whose rigid bed will support the glass plate firmly. [Kerslake (1998) page 46] . In addition, the press bed must be level and working conditions in the print shop immaculate. A particle of grit or dirt between press bed and the plate will create a tension point that will cause the glass to crack when pressure is applied. [Kerslake, 1998, page 44]
Development of Vitreography
American glass artist
Harvey Littletonwas a tenured professor of art at the University of Wisconsin in Madison when, in June 1974, he taught a workshop in cold-working techniques for glass artists. [The workshop was supported by the University of Wisconsin Research Committee, The National Endowment for the Artsand Corning Glassworks. Corning sent a glasscutter and glass engraver to assist Littleton in teaching the workshop. Byrd, J. Falconer (2004) page 29. Archives of American Art Journal, Volume 44 Numbers 3-4] To cold-work glass is to shape or sculpt cold (as opposed to hot or molten) glass, or to produce texture or decoration on its surface. Cold-working is done by carving, grinding or engraving glass with various tools, or by selectively blasting it with abrasives. As a result of experimenting with various resists for sandblasting, Littleton became intrigued by the possibility of printmaking from glass. [Littleton said that the experimental plates from the workshop stayed in his studio for about three weeks. As he related to Joan Byrd during a 2001 interview, “I kept looking at them and decided they really ought to be printed.” Byrd (2004) page 29] . He asked his colleague at the University of Wisconsin, printmaker Warrington Colescott, to ink five of the sandblasted plates from the workshop and print them onto paper in his etching press. The first plate broke under pressure, but after making some adjustments to the press, the rest of the glass plates printed “like dreamboats,” Colescott said. [Kessler, page 7] Editions printed from the plates looked promising, and Littleton was awarded a research grant from the University of Wisconsin to continue the development of printing from glass. [Lidh (1986) Introduction]
1976Littleton retired from teaching and moved to Spruce Pine, North Carolina, where he set up a glass studio, reserving space for an etching press on which he continued to make vitreograph prints. A few years later, at the end of 1981, he hired a woodcutartist, Sandy Willcox, to work as a part-time printer. He encouraged her and his colleagues in glass art, including Ken Carder, Billy Bernstein, Erwin Eisch and Ann Wolff (formerly Wärff), to try their hands at vitreography. [Kessler (1987) page 7]
1982Littleton invited curator Jane Kessler of the Mint Museum in Charlotte, North Carolina to see the prints that were being created at Littleton Studios. Kessler was impressed by the new technique, and recommended that experienced painters and printmakers be invited to the studio to explore the medium. A grant awarded by the National Endowment for the Arts made it possible for three painters, Walter Darby Bannard, Ed Blackburn and Hollis Sigler to collaborate with two master printers, Paul Maguire of Flatrock Press and June Lambla, who had apprenticed at Crown Point Press, in the creation of prints at Littleton Studios. By this time Littleton had constructed a fully equipped printmaking studio that was separate from his glassblowing shop. [Kessler, 1987, page 9] Sigler visited Littleton Studios in 1985and produced five prints; Blackburn produced five prints in 1986and Bannard created seven prints in 1987. The project led to an exhibition at the Mint Museum in 1987 that included a catalog detailing these and other artists’ research in glass plate printmaking. Littleton continued to invite painters, printmakers, potters and glass artists to the studio to fully develop the possibilities of vitreography. Littleton Studios has published vitreograph print editions by 110 artists. [ [http://www.littletoncollection.com] referenced May 20, 2008. The Littleton Collection is a retail gallery associated with Littleton Studios.]
Vitreography was initially conceived of as an
intaglioprocess, in which line and tone are carved, engraved or etched into the glass plate’s surface. Printing an intaglio plate involves forcing ink into the grooves and pits, and then wiping the plate’s surface with tarlatan [ Tarlatan is a stiff muslin used by etchers to wipe excess ink from intaglio plates.] to remove excess ink. The image is transferred to dampened paper under pressure in an etching press. [Petrie, K. (2006) Glass and Print, University of Pennsylvania Press, ISBN 0812219465 page 115 ] Color intaglio prints are achieved by processing separate plates, each carrying one or more colors in proportion to the effect desired in the print. The plates are printed in succession onto paper, each carrying color and imagery that, in register with the others, combine to form the finished print. [Kerslake (1998) page 44]
Tools used to make marks in the glass include diamond point scribers, a flexible shaft power tool with a diamond bit and a sandblaster. Littleton Studios printer Sandy Willcox and her husband David Lewis, a painter, are credited with discovering that white lithograph ink is a versatile resist for
sandblastingintaglio glass plates. They found that the viscous white ink, applied to the plate freely with a brush or evenly with a roller, can be drawn into by removing ink with wooden styluses, needles, or paintbrushes. When the drawing is complete, the plate is taken to the sandblasting booth wet. There, the initial onslaught of sand sticks to those areas of the image where ink remains (forming an even more resistant barrier) while etching those parts of the glass revealed by the hand of the artist. After the plate is cleaned of ink, the parts of the plate that received the blast can be seen to have minute pits that hold ink; the areas that were protected by the white litho ink remain smooth and are wiped clean before printing. [Kessler (1987) pages 36-37] Contact paper and tape are also used on the plates as a sandblasting resist; those materials create imagery with a hard-edged, stencil effect. Diluted hydrofluoric acid, available under the trade name “Jack Frost,” can be brushed onto the plate to create areas of very delicate tone. [Kerslake (1998) page 45]
A second method of creating imagery on the vitreograph plate is waterless lithography (sometimes called “siligraphy”). The process was originally developed by
3M Companyfor commercial printing in the late 1960s; it was purchased and subsequently refined by Toray Industriesof Japan. The commercial process is a type of offset printingthat uses photo-sensitized silicone rubber plates. [ [http://printwiki.org/Waterless_Lithography Waterless Lithography - PrintWiki ] ] The waterless lithography process employed in fine art printmaking has been credited to Nik Semenoff, who developed it for use on metal plates. [Semenoff, N. [http://www.polymetaal.nl/beguin/mapw/waterlesslithography/waterlesslitho01.htm] “Waterless Lithography Using Common Caulking Silicone”, accessed May 20, 2008] Littleton Studios adapted the process for use on ground glass plates. The image is drawn onto a ground glass matrix with water-soluble art materials, over which is applied a film of common caulking siliconethinned with synthetic turpentine. Master printer Mark Mahaffey has found that frosted Mylarcan be used as a printing matrix as well as 3/8” float glass to create a vitreograph using waterless lithography. [Mahaffey, M. [http://www.baschwar.com/printmakers/Vitreography111499/index.html] “Vitreography Demonstration”, Accessed May 16,2008] After the silicone layer cures, the original drawing is gently washed from the plate with water, dried, and inked with a roller. The silicone layer protects the non-printing areas of the image while allowing open areas (those free of silicone) to accept ink. [Waggoner, S. (1998) “The Vitreographer”, page 48. Glass Art, Vol. 13 No. 3] Like intaglio vitreographs, waterless lithographs on glass plates are transferred to paper in an etching press.
In 1998 Littleton invited three artists, Bonnie Pierce Lhotka, Karin Schminke and Dorothy Simpson Krause (collectively known as the Digital Atelier), to investigate combining digital imagery with vitreography processes. [Schminke et al. (2004) “Digital Art Studio: Techniques for Combining Inkjet Printing with Traditional Art Materials”, page 118. Watson-Guptill Publications, New York ISBN 0-8230-1342-1] The artists printed digital images onto clear transfer film using a large format inkjet printer, transferring them to paper in the etching press, along with glass plate imagery processed in the intaglio and/or siligraph techniques. [Schminke et al. (2004) page 118] Since that time a number of artists, including Herb Jackson, Karen Kunc, Judith O’Rourke, Therman Statom and Dan Welden have combined digital transfer with vitreography in works created at Littleton Studios.
Exhibition of Vitreographs
The first public exhibition of Littleton’s own intaglio prints from glass plates was at the Brooks Memorial Art Museum in Memphis, Tennessee in
1975. There the prints were shown along with Littleton’s glass sculptures. [Lidh (1986) Introduction] The same was the case with Ann Wolff’s glass plate intaglios, which were included in a show of her glass artworks, drawings and copper plate intaglios in 1986at Holsten Galleries in Palm Beach. [Holsten, C & Holsten, K. (1986) “Ann Wolff”, Pages 18-19. Holsten Galleries, Palm Beach, FL]
The first group exhibition of the prints to include works by painters and printmakers, as well as glass artists, was at Western Carolina University in Cullowhee, North Carolina in 1986. Seventeen artists were represented in the exhibition, all of whom had created their prints at Littleton Studios. [Lidh, W. 1986, Introduction]
The Mint Museum mounted another group exhibition in
1987titled Luminous Impressions: Prints from Glass Plates. It featured vitreographs by nineteen artists and included prints by glass artist Dale Chihulyand California printmaker Connor Everts. [Kessler 1987, pages 36-37] Everts is credited with coining the term “vitreography” to describe printmaking from glass plates. [Kerslake, K. (2001) The Vitreographic
] Another early group exhibition took place in 1988 at the Kunstsammlungen der Veste Coburg in Coburg, Germany. Titled "Prints from Glass Plates - Vitreographs," the show featured works by Americans and two German: Erwin Eisch ans Ann Wolff. [Neue Presse, "Glas als Gefãß und als Druck-Werkstoff", March 19, 1988, Coburg, Germany]
Other notable group exhibitions include "Vitreographs: Collaborative Works from the Littleton Studio" which was exhibited at The
Hunter Museum of American Artin Chattanooga, Tennessee and The University Gallery at The University of Florida at Gainesville (both in 1993); “Vitreographs” at The Portland Art Museum in Portland, Oregon in 1997 and “Vitreographs: Collaborative Works from Littleton Studio” at the Center for the Arts in Vero Beach, Florida in 1998.
Recent group exhibitions include "Reflections on a Legacy: Vitreographs from Littleton Studios" at
Appalachian State Universityin Boone, North Carolina (2006) and "Harvey K. Littleton + Friends: A Legacy of Transforming Object, Image & Idea," at Western Carolina Universityin Cullowhee, North Carolina (2006-07). The latter was an exhibition of the work of 75 artworks by seventeen artists, and included vitreographs alongside works in glass, clay, ceramic, painting and book art. Curator Martin DeWitt wrote in the catalog accompanying the exhibition that “Not only is Littleton credited to be the father of the contemporary studio glass movement in the United States…he is also inventor and progenitor of the versatile and unique vitreographic printmaking process.” [De Witt, M. (2006) Fine Art Museum at the Fine & Performing Arts Center, Western Carolina University, The University of North Carolina, Page 4]
Vitreographs in Public Collections
Vitreograph prints can be found in collections in the United States, including the Achenbach Foundation for Graphic Art, San Francisco; Burroughs Chapin Art Museum, Myrtle Beach, South Carolina;
Cincinnati Art Museum, Cincinnati, Ohio; The Corning Museum of Glass, Corning, New York; Samuel P. Harn Museum of Art, University of Florida, Gainesville, Florida; Milwaukee Art Museum, Milwaukee, Wisconsin; Museum of Fine Arts, St. Petersburg, Florida; Portland Art Museum, Portland, Oregon; Sherwin Miller Museum of Jewish Art, Tulsa, Oklahoma; Smithsonian American Art Museum, Washington, DC; Tweed Museum of Art, Duluth, Minnesota and the Vero Beach Museum of Art, Vero Beach, Florida. The Fine Art Museum of Western Carolina University holds an archive of 723 vitreograph editions published at Littleton Studios. [Executive Director Martin De Witt, telephone conversation May 21, 2008, Fine and Performing Arts Center, Western Carolina University, Cullowhee, North Carolina]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Herb Jackson — Infobox Artist name = Herb Jackson imagesize = caption = birthname = birthdate = 1945 location = Raleigh, North Carolina, U.S. nationality = field = Painting, Drawing with Oil Crayons, Printmaking training = Davidson College, Philipps University … Wikipedia
-graphy — is an English suffix. Words that include the suffix usually are about a work, an art, or a field of study. Contents 1 Etymology 2 Arts 2.1 Writing 2.2 Science … Wikipedia
Harvey Littleton — Infobox Person name = Harvey K. Littleton caption = birth date = June 14, 1922 birth place = death date = death place = other names = known for = Founder, American studio glass movement occupation = Artist, educator nationality = U.S.… … Wikipedia
Mildred Thompson — Born 1936 Jacksonville, Florida Died 2003 Atlanta, Georgia Nationality U.S. citizen Occupation Artist, educator, writer Mildred Thompson (1936–2003) was an Afr … Wikipedia