Compressibility factor

Compressibility factor

The compressibility factor (Z), also known as the compression factor, is a useful thermodynamic property for modifying the ideal gas law to account for the real gas behavior.[1] In general, deviation from ideal behavior becomes more significant the closer a gas is to a phase change, the lower the temperature or the larger the pressure. Compressibility factor values are usually obtained by calculation from equations of state (EOS), such as the virial equation which take compound specific empirical constants as input. For a gas that is a mixture of two or more pure gases (air or natural gas, for example), a gas composition is required before compressibility can be calculated.
Alternatively, the compressibility factor for specific gases can be read from generalized compressibility charts[1] that plot Z as a function of pressure at constant temperature.

Contents

Definition and physical significance

The compressibility factor is defined as

Z=\frac{V_{\mathrm{m}}}{(V_{\mathrm{m}})_{\text{ideal gas}}}=\frac{p V_{\mathrm{m}}}{R T},

where Vm is the molar volume, (Vm)ideal gas = RT / p is the molar volume of the corresponding ideal gas, p is the pressure, T is the temperature, and R is the gas constant. For engineering applications, it is frequently expressed as

Z=\frac{p}{\rho R_{\rm specific} T},

where ρ is the density of the gas and Rspecific = R / M is the specific gas constant,[2] M being the molar mass.

For an ideal gas the compressibility factor is Z = 1 per definition. In many real world applications requirements for accuracy demand that deviations from ideal gas behaviour, i.e., real gas behaviour, is taken into account. The value of Z generally increases with pressure and decreases with temperature. At high pressures molecules are colliding more often. This allows repulsive forces between molecules to have a noticeable effect, making the molar volume of the real gas (Vm) greater than the molar volume of the corresponding ideal gas ((Vm)ideal gas = RT / p), which causes Z to exceed one.[3] When pressures are lower, the molecules are freer to move. In this case attractive forces dominate, making Z < 1. The closer the gas is to its critical point or its boiling point, the more Z deviates from the ideal case.

Generalized compressibility factor graphs for pure gases

Generalized compressibility factor diagram.

The unique relationship between the compressibility factor and the reduced temperature, Tr, and the reduced pressure, Pr, was first recognized by Johannes Diderik van der Waals in 1873 and is known as the two-parameter principle of corresponding states. The principle of corresponding states expresses the generalization that the properties of a gas which are dependent on intermolecular forces are related to the critical properties of the gas in a universal way. That provides a most important basis for developing correlations of molecular properties.

As for the compressibility of gases, the principle of corresponding states indicates that any pure gas at the same reduced temperature, Tr, and reduced pressure, Pr, should have the same compressibility factor.

The reduced temperature and pressure are defined by

T_r = \frac{T}{T_c} and P_r = \frac{P}{P_c}.

Here Tc and Pc are known as the critical temperature and critical pressure of a gas. They are characteristics of each specific gas with Tc being the temperature above which it is not possible to liquify a given gas and Pc is the minimum pressure required to liquify a given gas at its critical temperature. Together they define the critical point of a fluid above which distinct liquid and gas phases of a given fluid do not exist.

The pressure-volume-temperature (PVT) data for real gases varies from one pure gas to another. However, when the compressibility factors of various single-component gases are graphed versus pressure along with temperature isotherms many of the graphs exhibit similar isotherm shapes.

In order to obtain a generalized graph that can be used for many different gases, the reduced pressure and temperature, Pr and Tr, are used to normalize the compressibility factor data. Figure 2 is an example of a generalized compressibility factor graph derived from hundreds of experimental PVT data points of 10 pure gases, namely methane, ethane, ethylene, propane, n-butane, i-pentane, n-hexane, nitrogen, carbon dioxide and steam.

There are more detailed generalized compressibility factor graphs based on as many as 25 or more different pure gases, such as the Nelson-Obert graphs. Such graphs are said to have an accuracy within 1-2 percent for Z values greater than 0.6 and within 4-6 percent for Z values of 0.3-0.6.

The generalized compressibility factor graphs may be considerably in error for strongly polar gases which are gases for which the centers of positive and negative charge do not coincide. In such cases the estimate for Z may be in error by as much as 15-20 percent.

The quantum gases hydrogen, helium, and neon do not conform to the corresponding-states behavior and the reduced pressure and temperature for those three gases should be redefined in the following manner to improve the accuracy of predicting their compressibility factors when using the generalized graphs:

   T_r = \frac{T}{T_c + 8}   and   P_r = \frac{P}{P_c + 8}

Theoretical models

The virial equation is especially useful to describe the causes of non-ideality at a molecular level (very few gases are mono-atomic) as it is derived directly from statistical mechanics:

\frac{P V_{\mathrm{m}}}{RT} = 1 + \frac{B}{V_{\mathrm{m}}} + \frac{C}{V_{\mathrm{m}}^2} + \frac{D}{V_{\mathrm{m}}^3} + \dots

Where the coefficients in the numerator are known as virial coefficients and are functions of temperature.

The virial coefficients account for interactions between successively larger groups of molecules. For example, B accounts for interactions between pairs, C for interactions between three gas molecules, and so on. Because interactions between large numbers of molecules are rare, the virial equation is usually truncated after the third term.[4]

The Real gas article features more theoretical methods to compute compressibility factors

Experimental values

It is extremely difficult to generalize at what pressures or temperatures the deviation from the ideal gas becomes important. As a rule of thumb, the ideal gas law is reasonably accurate up to a pressure of about 2 atm, and even higher for small non-associating molecules. For example methyl chloride, a highly polar molecule and therefore with significant intermolecular forces, the experimental value for the compressibility factor is Z = 0.9152 at a pressure of 10 atm and temperature of 100 °C.[5] For air (small non-polar molecules) at approximately the same conditions, the compressibility factor is only Z = 1.0025 (see table below for 10 bars, 400 K).

Compressibility of air

Normal air comprises in crude numbers 80 percent nitrogen N2 and 20 percent oxygen O2. Both molecules are small and non-polar (and therefore non-associating). We can therefore expect that the behaviour of air within broad temperature and pressure ranges can be approximated as an ideal gas with reasonable accuracy. Experimental values for the compressibility factor confirm this.

Compressibility factor for air (experimental values)
  Pressure, bar (absolute)
Temp, K 1 5 10 20 40 60 80 100 150 200 250 300 400 500
75 0.0052 0.0260 0.0519 0.1036 0.2063 0.3082 0.4094 0.5099 0.7581 1.0125
80 0.0250 0.0499 0.0995 0.1981 0.2958 0.3927 0.4887 0.7258 0.9588 1.1931 1.4139
90 0.9764 0.0236 0.0453 0.0940 0.1866 0.2781 0.3686 0.4681 0.6779 0.8929 1.1098 1.3110 1.7161 2.1105
100 0.9797 0.8872 0.0453 0.0900 0.1782 0.2635 0.3498 0.4337 0.6386 0.8377 1.0395 1.2227 1.5937 1.9536
120 0.9880 0.9373 0.8860 0.6730 0.1778 0.2557 0.3371 0.4132 0.5964 0.7720 0.9530 1.1076 1.5091 1.7366
140 0.9927 0.9614 0.9205 0.8297 0.5856 0.3313 0.3737 0.4340 0.5909 0.7699 0.9114 1.0393 1.3202 1.5903
160 0.9951 0.9748 0.9489 0.8954 0.7803 0.6603 0.5696 0.5489 0.6340 0.7564 0.8840 1.0105 1.2585 1.4970
180 0.9967 0.9832 0.9660 0.9314 0.8625 0.7977 0.7432 0.7084 0.7180 0.7986 0.9000 1.0068 1.2232 1.4361
200 0.9978 0.9886 0.9767 0.9539 0.9100 0.8701 0.8374 0.8142 0.8061 0.8549 0.9311 1.0185 1.2054 1.3944
250 0.9992 0.9957 0.9911 0.9822 0.9671 0.9549 0.9463 0.9411 0.9450 0.9713 1.0152 1.0702 1.1990 1.3392
300 0.9999 0.9987 0.9974 0.9950 0.9917 0.9901 0.9903 0.9930 1.0074 1.0326 1.0669 1.1089 1.2073 1.3163
350 1.0000 1.0002 1.0004 1.0014 1.0038 1.0075 1.0121 1.0183 1.0377 1.0635 1.0947 1.1303 1.2116 1.3015
400 1.0002 1.0012 1.0025 1.0046 1.0100 1.0159 1.0229 1.0312 1.0533 1.0795 1.1087 1.1411 1.2117 1.2890
450 1.0003 1.0016 1.0034 1.0063 1.0133 1.0210 1.0287 1.0374 1.0614 1.0913 1.1183 1.1463 1.2090 1.2778
500 1.0003 1.0020 1.0034 1.0074 1.0151 1.0234 1.0323 1.0410 1.0650 1.0913 1.1183 1.1463 1.2051 1.2667
600 1.0004 1.0022 1.0039 1.0081 1.0164 1.0253 1.0340 1.0434 1.0678 1.0920 1.1172 1.1427 1.1947 1.2475
800 1.0004 1.0020 1.0038 1.0077 1.0157 1.0240 1.0321 1.0408 1.0621 1.0844 1.1061 1.1283 1.1720 1.2150
1000 1.0004 1.0018 1.0037 1.0068 1.0142 1.0215 1.0290 1.0365 1.0556 1.0744 1.0948 1.1131 1.1515 1.1889

Source: Perry's chemical engineers' handbook (6ed ed.). MCGraw-Hill. 1984. ISBN 0-07-049479-7.  (table 3-162). Z values are calculated from values of pressure, volume (or density), and temperature in Vassernan, Kazavchinskii, and Rabinovich, "Thermophysical Properties of Air and Air Components;' Moscow, Nauka, 1966, and NBS-NSF Trans. TT 70-50095, 1971: and Vassernan and Rabinovich, "Thermophysical Properties of Liquid Air and Its Component, "Moscow, 1968, and NBS-NSF Trans. 69-55092, 1970.

Compressibility of ammonia gas

Ammonia is small but highly polar molecule with significant interactions. Values can be obtained from Perry 4th ed (awaits future library visit)

See also

References

  1. ^ a b Properties of Natural Gases. Includes a chart of compressibility factors versus reduced pressure and reduced temperature (on last page of the PDF document)
  2. ^ Zucker, Robert D. and Biblarz, Oscar (2002). Fundamentals of Gas Dynamics (2nd ed.). Wiley Books. ISBN 0-471-05967-6.  page 327
  3. ^ McQuarrie, Donald A. and Simon, John D. (1999). Molecular Thermodynamics. University Science Books. ISBN 1-891389-05-X.  page 55
  4. ^ Smith, J.M. et al. (2005). Introduction to Chemical Engineering Thermodynamics (Seventh Edition ed.). McGraw Hill. ISBN 0-07-310445-0.  page73
  5. ^ Perry's chemical engineers' handbook (6ed ed.). MCGraw-Hill. 1984. ISBN 0-07-049479-7.  page 3-268

External links



Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • compressibility factor — spūdumo faktorius statusas T sritis Standartizacija ir metrologija apibrėžtis Apibrėžtį žr. priede. priedas( ai) Grafinis formatas atitikmenys: angl. compressibility factor vok. Realgasfaktor, m rus. коэффициент сжимаемости, m pranc. facteur de… …   Penkiakalbis aiškinamasis metrologijos terminų žodynas

  • compressibility factor — spūdumo faktorius statusas T sritis fizika atitikmenys: angl. compressibility factor vok. Realgasfaktor, m rus. коэффициент сжимаемости, m pranc. facteur de compressibilité, m …   Fizikos terminų žodynas

  • Compressibility — This article is about thermodynamics and fluid mechanics. For other uses, see Compression (disambiguation). Incompressibility redirects here. For the property of vector fields, see Solenoidal vector field. Thermodynamics …   Wikipedia

  • Acentric factor — In thermodynamics, the acentric factor omega is a factor originally used by K.S. Pitzer and coworkers as an expression in an equation for the compressibility factor. It is defined asomega = log {10} (P^{ m{sat r) 1 { m at } T r = 0{.}7.T r stands …   Wikipedia

  • Коэффициент сверхсжимаемости газа — ► compressibility factor Показатель отношения объемов реального и идеального газов при одних и тех же давлении и температуре. Является поправочным коэффициентом при применении уравнения Клапейрона для реальных газов …   Нефтегазовая микроэнциклопедия

  • Gas — This article is about the physical properties of gas as a state of matter. For the uses of gases, and other meanings, see Gas (disambiguation). Ga …   Wikipedia

  • Orifice plate — Flat plate, sharp edge orifice ISO 5167 Orifice Plate An orifice plate is a device used for measuring the volumetric flow rate. It …   Wikipedia

  • Incompressible flow — In fluid mechanics or more generally continuum mechanics, an incompressible flow is solid or fluid flow in which the divergence of velocity is zero. This is more precisely termed isochoric flow. It is an idealization used to simplify analysis. In …   Wikipedia

  • Theorem of corresponding states — The theorem of corresponding states originated with the work of Johannes Diderik van der Waals in about 1873 [ [http://digital.library.okstate.edu/oas/oas pdf/v56/p125 132.pdf A Four Parameter Corresponding States Correlation for Fluid… …   Wikipedia

  • Ideal gas — Thermodynamics …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”