- Optical heterodyne detection
Optical heterodyne detection is an important special case of heterodyne detection. In heterodyne detection, a signal of interest at some frequency is non-linearly mixed with a reference "local oscillator" (LO) that is set at a close-by frequency. The desired outcome is the difference frequency, which carries the information (amplitude, phase, and frequency modulation) of the original higher frequency signal, but is oscillating at a lower more easily processed carrier frequency.
Optical heterodyne detection has special characteristics and special problems that distinguish it from conventional RF heterodyne detection. The electrical field cannot be directly measured, since the relatively high optical frequencies have oscillating fields that are much faster than electronics can respond. As such, the LO and the reference are typically mixed on a photodiode  While an old technique, key limiting issues were solved only as recently as 1994 with the invention of synthetic array heterodyne detection.
- 1 Contrast to conventional radio frequency (RF) heterodyne detection
- 2 Key benefits
- 3 Key problems and their solutions
- 4 See also
- 5 References
- 6 External links
Contrast to conventional radio frequency (RF) heterodyne detection
It is instructive to contrast the practical aspects of optical band detection to radio frequency (RF) band heterodyne detection.
Energy versus electric field detection
Unlike Radio Frequency (RF) band detection, optical frequencies oscillate too rapidly to directly measure and process the electric field electronically. Instead optical photons are (usually) detected by absorbing the photon's energy, thus only revealing the magnitude, and not by following the electric field phase. Hence the primary purpose of heterodyne mixing is to down shift the signal from the optical band to an electronically tractable frequency range.
In RF band detection, typically, the electromagnetic field drives oscillatory motion of electrons in an antenna; the captured EMF is subsequently electronically mixed with a local oscillator (LO) by any convenient non-linear circuit element with a quadratic term (most commonly a rectifier). In optical detection, the desired non-linearity is embedded in the photon absorption process itself. Conventional light detectors—so called "Square-law detectors"-- respond to the photon energy to free bound electrons, and since the energy flux scales as the square of the electric field, so does the rate at which electrons are freed. A difference frequency only appears in the detector output current when both the LO and signal illuminate the detector at the same time, causing the square of their combined fields to have cross term or "difference" frequency modulating the average rate at which free electrons are generated.
Wideband local oscillators for coherent detection
Another point of contrast is the expected bandwidth of the signal and local oscillator. Typically, an RF local oscillator is a pure frequency; pragmatically, "purity" means that a local oscillator's frequency bandwidth is much much less than the difference frequency. With optical signals, even with a laser, it is not simple to produce a reference frequency sufficiently pure to have either an instantaneous bandwidth or long term temporal stability that is less than a typical megahertz or kilohertz scale difference frequency. For this reason, the same source is often used to produce the LO and the signal so that their difference frequency can be kept constant even if the center frequency wanders.
As a result, the mathematics of squaring the sum of two pure tones, normally invoked to explain RF heterodyne mixing, is an oversimplified model of optical heterodyne detection. Nevertheless, the intuitive pure-frequency heterodyne concept still holds perfectly for the wideband case provided that the signal and LO are mutually coherent. Indeed, one can obtain narrow-band interference from coherent broadband sources: this is the basis for white light interferometry and optical coherence tomography. Mutual coherence permits the rainbow in Newton's rings, and supernumerary rainbows.
Consequently, optical heterodyne detection is usually performed as interferometry where the LO and signal share a common origin, rather than, as in radio, a transmitter sending to a remote receiver. That is to say, the remote receiver geometry is unusual because generating a local oscillator signal that is mutually coherent with a signal of independent origin is technologically difficult at optical frequencies. However, lasers of sufficiently narrow linewidth to allow the signal and LO to originate from different lasers do exist.
Gain in the detection
The amplitude of the down-mixed difference frequency can be larger than the amplitude of the original signal itself. The difference frequency signal is proportional to the product of the amplitudes of the LO and signal electric fields. Thus the larger the LO amplitude, the larger the difference-frequency amplitude. Hence there is gain in the photon conversion process itself.
Preservation of optical phase
If the optical phase of the signal beam shifts by an angle theta, then the phase of the electronic difference frequency shifts by exactly the same angle theta. More properly, to discuss an optical phase shift one needs to have a common time base reference. Typically the signal beam is derived from the same laser as the LO but shifted by some modulator in frequency. In other cases, the frequency shift may arise from reflection from a moving object. As long as the modulation source maintains a constant offset phase between the LO and signal source, any added optical phase shifts over time arising from external modification of the return signal are added to the phase of the difference frequency and thus are measurable.
Mapping optical frequencies to electronic frequencies allows sensitive measurements
As noted above, the difference frequency linewidth can be much smaller than the optical linewidth of the signal and LO signal, provided the two are mutually coherent. Thus small shifts in optical signal center-frequency can be measured: For example, Doppler lidar systems can discriminate wind velocities with a resolution better than 1 meter per second, which is less than a part in a billion shift in the optical frequency. Likewise small coherent phase shifts can be measured even for nominally incoherent light, allowing optical coherence tomography to image micrometer-sized features. Moreover, an electronic filter can define an effective optical bandwidth that is narrower than any realizable wavelength filter operating on the light itself, and thereby enable background light rejection and hence the detection of weak signals.
Noise reduction to shot noise limit
As with any small signal amplification, it's most desirable to get gain as close as possible to the initial point of the signal interception: moving the gain ahead of any signal processing reduces the additive contributions of effects like resistor Johnson-Nyquist noise, or electrical noises in active circuits. In optical heterodyne detection, the mixing-gain happens directly in the physics of the initial photon absorption event, making this ideal.
One of the virtues of heterodyne detection is that the difference frequency is generally far removed spectrally from the potential noises radiated during the process of generating either the signal or the LO signal, thus making the spectral region near the difference frequency relatively quiet. Hence, narrow electronic filtering near the difference frequency is highly effective at removing the remaining, generally broadband, noise sources.
The primary remaining source of noise is photon shot noise from the nominally constant level of the Local Oscillator (LO) on the optical detector. Since the Shot noise scales as the amplitude of the LO electric field level, and the heterodyne gain also scales the same way, the ratio of the shot noise to the mixed signal is constant no matter how large the LO.
Thus in practice one increases the LO level, until the gain on the signal raises it above all other noise sources, leaving only the shot noise. At that point there is no change in the signal to noise as the gain is raised further. (Of course, this is a highly idealized description.)
Key problems and their solutions
AC detection and imaging
Array detection of light, for instance, as applied in digital cameras, is common place. However that is only possible because each pixel can integrate the light level prior to serially reading out the array. With heterodyne detection the signal at each pixel is oscillating with a zero average and is often multi-frequency, so a pixel cannot be integrated directly on the chip to a scalar value. Thus a heterodyne array must have parallel direct connections from every sensor pixel to separate electrical amplifiers, filters, and processing systems. This makes large, general purpose, heterodyne imaging systems prohibitively expensive. For example, simply attaching 1 million leads to a megapixel coherent array is a daunting challenge.
To solve this problem, synthetic array heterodyne detection was developed. In SAHD, large imaging arrays can be multiplexed into virtual pixels on a single element detector with single readout lead, single electrical filter, and single recording system. The time domain conjugate of this approach is Fourier transform heterodyne detection, which also has the multiplex advantage and also allows a single element detector to act like an imaging array. SAHD has been implemented as Rainbow heterodyne detection in which instead of a single frequency LO, many narrowly-spaced frequencies are spread out across the detector element surface like a rainbow. The physical position where each photon arrived is encoded in the resulting difference frequency itself, making a virtual 1D array on a single element detector. If the frequency comb is evenly spaced then, conveniently, the Fourier transform of the output waveform is the image itself. Arrays in 2D can be created as well, and since the arrays are virtual, the number of pixels, their size, and their individual gains can be adapted dynamically. Because this technique uses more total LO power (spread over multiple pixels) it has more total shot noise than a single pixel detector at the same pixel power density.
Speckle and diversity reception
As discussed, the LO and signal must be temporally coherent. They also need to be spatially coherent across the face of the detector or they will destructively interfere. In many usage scenarios the signal is reflected from optically rough surfaces or passes through optically turbulent media leading to wavefronts that are spatially incoherent. In laser scattering this is known as speckle.
In RF detection the antenna is rarely larger than the wavelength so all excited electrons move coherently within the antenna, whereas in optics the detector is usually much larger than the wavelength and thus can intercept a distorted phase front, resulting in destructive interference by out-of-phase photo-generated electrons within the detector.
Interestingly, while destructive interference dramatically reduces the signal level, the summed amplitude of a spatially incoherent mixture does not approach zero but rather the mean amplitude of a single speckle. However, since the standard deviation of the coherent sum of the speckles is exactly equal to the mean speckle intensity, optical heterodyne detection of scrambled phase fronts can never measure the absolute light level with an error bar less than the size of the signal itself. This upper bound signal-to-noise ratio of unity is only for absolute magnitude measurement: it can have signal-to-noise ratio better than unity for phase, frequency or time-varying relative-amplitude measurements in a stationary speckle field.
In RF detection, "diversity reception" is often used when the primary antenna is coincidentally located at an interference null point: by having more than one antenna one can adaptively switch to whichever antenna has the strongest signal or even incoherently add all of the antenna signals. Simply adding the antenna coherently can produce destructive interference just as happens in the optical realm.
The analogous diversity reception for optical heterodyne has been demonstrated with arrays of photon-counting detectors. For incoherent addition of the multiple element detectors in a random speckle field, the ratio of the mean to the standard deviation will scale as the square root of the number of independently measured speckles. This improved signal-to-noise ratio makes absolute amplitude measurements feasible in heterodyne detection.
However, as noted above, scaling physical arrays to large element counts is challenging for heterodyne detection due to the oscillating or even multi-frequency nature of the output signal. Instead, a single-element optical detector can also act like diversity receiver via synthetic array heterodyne detection or Fourier transform heterodyne detection. With a virtual array one can then either adaptively select just one of the LO frequencies, track a slowly moving bright speckle, or add them all in post-processing by the electronics.
One can incoherently add the magnitudes of N-independent pulses to obtain a √N improvement in the signal to noise on the amplitude, but at the expense of losing the phase information. Instead coherent addition (adding the complex magnitude and phase) of multiple pulse waveforms would improve the signal to noise by a factor of N, not its square root, and preserve the phase information. The practical limitation is adjacent pulses from typical lasers have a minute frequency drift that translates to a large random phase shift in any long distance return signal, and thus just like the case for adjacent mixed phase pixels, destructively interfere when added coherently. However, coherent addition of multiple pulses is possible with advanced laser systems that narrow the frequency drift far below the difference frequency (intermediate frequency). This technique has been demonstrated in multi-pulse coherent Doppler LIDAR.
- ^ Encyclopedia of Laser Physics and Technology "Optical Heterodyne Detection"
- ^ Strauss, Charlie E. M. (1994). "Synthetic-array heterodyne detection: a single-element detector acts as an array". Optics Letters 19 (20): 1609. doi:10.1364/OL.19.001609. PMID 19855597.
- ^ Hinkley, E.; Freed, Charles (1969). "Direct Observation of the Lorentzian Line Shape as Limited by Quantum Phase Noise in a Laser above Threshold". Physical Review Letters 23: 277. Bibcode 1969PhRvL..23..277H. doi:10.1103/PhysRevLett.23.277.
- ^ Cooke BJ et al., "Laser field imaging through Fourier transform heterodyne"Laser Radar Technology and Applications IV, Vol. 3707, No. 1. (1999), pp. 390-408.
- ^ Strauss, C.E.M. and Rehse, S.J. "Rainbow heterodyne detection" Lasers and Electro-Optics, 1996. CLEO Pub Date: 2–7 June 1996 (200) ISBN 1-55752-443-2 (See DOE archive)
- ^ a b Dainty C (Ed), Laser Speckle and Related Phenomena, 1984, Springer Verlag, ISBN 0387131698
- ^ Jiang, Leaf A.; Luu, Jane X. (2008). "Heterodyne detection with a weak local oscillator". Applied Optics 47 (10): 1486. doi:10.1364/AO.47.001486. PMID 18382577.
- ^ Gabriel Lombardi, Jerry Butman, Torrey Lyons, David Terry, and Garrett Piech, "Multiple-pulse coherent laser radar waveform"
Wikimedia Foundation. 2010.
Look at other dictionaries:
Heterodyne detection — is a method of detecting radiation by non linear mixing with radiation of a reference frequency. It is commonly used in telecommunications and astronomy for detecting and analysing signals.The radiation in question is most commonly either radio… … Wikipedia
Noise-immune cavity-enhanced optical heterodyne molecular spectroscopy — (NICE OHMS) is an ultra sensitive laser based absorption technique that utilizes laser light to assess the concentration or the amount of a species in gas phase by absorption spectrometry (AS). Contents 1 Principles 1.1 Types of signals 1.2… … Wikipedia
Noise-Immune Cavity-Enhanced Optical-Heterodyne Molecular Spectroscopy — (NICE OHMS) is an ultra sensitive laser based absorption technique that utilizes laser light to assess the concentration or the amount of a species in gas phase by absorption spectrometry (AS). Principles The NICE OHMS technique combines in a… … Wikipedia
Optical coherence tomography — Intervention Optical Coherence Tomography (OCT) image of a sarcoma MeSH … Wikipedia
Heterodyne — This article is about waveform manipulation. For the use of the term in poetry, see Heterodyne (poetry). For the webcomic characters, see Girl Genius. Heterodyning is a radio signal processing technique invented in 1901 by Canadian inventor… … Wikipedia
Optical hybrid — A 90° optical hybrid is a six port device that is used for coherent signal demodulation for either homodyne or heterodyne detection. It would mix the incoming signal with the four quadratural states associated with the reference signal in the… … Wikipedia
Homodyne detection — is a method of detecting frequency modulated radiation by non linear mixing with radiation of a reference frequency, the same principle as for heterodyne detection.In optical interferometry, homodyne signifies that the reference radiation (the… … Wikipedia
Astronomical optical interferometry — One of the first astronomical interferometers was built on the Mount Wilson Observatory s reflector telescope in 1920 in order to measure the diameters of stars. The red giant star Betelgeuse was among the first to have its diameter determined in … Wikipedia
Interferometry — is the technique of using the pattern of interference created by the superposition of two or more waves to diagnose the properties of the aforementioned waves. The instrument used to interfere the waves together is called an interferometer.… … Wikipedia
LIDAR — A FASOR used at the Starfire Optical Range for LIDAR and laser guide star experiments is tuned to the sodium D2a line and used to excite sodium atoms in the upper atmosphere … Wikipedia