Cascode

Cascode

The cascode is a two-stage amplifier composed of a transconductance amplifier followed by a current buffer. Compared to a single amplifier stage, this combination may have one or more of the following advantages: higher input-output isolation, higher input impedance, higher output impedance, higher gain or higher bandwidth. In modern circuits, the cascode is often constructed from two transistors, with one operating as a common emitter or common source and the other as a common base or common gate.The cascode improves input-output isolation (or reverse transmission) as there is no direct coupling from the output to input. This eliminates the Miller effect and thus contributes to a higher bandwidth.

History

The cascode (sometimes to "cascoding") is a universal technique for improving analog circuit performance, applicable to both vacuum tubes and transistors. The word "cascode" is a contraction of the phrase "casc"ade to cath"ode". It was first used in an article by F.V. Hunt and R.W. Hickman in 1939, in a discussion for application in low-voltage stabilizers. [Hickman, R. W. and Hunt, F. V., “On Electronic Voltage Stabilizers,” "Review of Scientific Instruments", vol. 10, p. 6-21 (January 1939).] They proposed a cascode of two triodes (first one with common cathode, the second one with common grid) as a replacement of a pentode.

Operation

Figure 1 shows an example of cascode amplifier with a common source amplifier as input stage driven by signal source "Vin". This input stage drives a common gate amplifier as output stage, with output signal "Vout".

The major advantage of this circuit arrangement stems from the placement of the upper FET as the load of the input (lower) FET's output terminal (drain). Because at operating frequencies the upper FET's gate is effectively grounded, the upper FET's source voltage (and therefore the input transistor's drain) is held at nearly constant voltage during operation. In other words, the upper FET exhibits a low input resistance to the lower FET, making the voltage gain of the lower FET very small, which dramatically reduces the Miller feedback capacitance from the lower FET's drain to gate. This loss of voltage gain is recovered by the upper FET. Thus, the upper transistor permits the lower FET to operate with minimum negative (Miller) feedback, improving its bandwidth.

The upper FET gate is electrically grounded, so charge and discharge of stray capacitance "Cdg" between drain and gate is simply through "RD" and the output load (say "Rout"), and the frequency response is affected only for frequencies above the associated RC time constant: τ = Cdg RD//Rout, namely "f = 1/(2πτ)", a rather high frequency because "Cdg" is small. That is, the upper FET gate does not suffer from Miller amplification of "Cdg".

If the upper FET stage were operated alone using its source as input node, it would have good voltage gain and wide bandwidth. However, its low input impedance would limit its usefulness to very low impedance voltage drivers. Adding the lower FET results in a high input impedance, allowing the cascode stage to be driven by a high impedance source.

On the other hand, if the upper FET was replaced by a typical inductive/resistive load, and only the input transistor used with the output taken from the input transistor's drain, the cascode configuration offers the same input impedance, potentially greater gain and much greater bandwidth.

tability

The cascode arrangement is also very stable. Its output is effectively isolated from the input both electrically and physically. The lower transistor has nearly constant voltage at both drain and source and thus there is essentially "nothing" to feed back into its gate. The upper transistor has nearly constant voltage at its gate and source. Thus, the only nodes with significant voltage on them are the input and output, and these are separated by the central connection of nearly constant voltage and by the physical distance of two transistors. Thus in practice there is little feedback from the output to the input. Metal shielding is both effective and easy to provide between the two transistors for even greater isolation when required. This would be difficult in one-transistor amplifier circuits, which at high frequencies would require neutralization.

Biasing

As shown, the cascode circuit using two "stacked" FET's imposes some restrictions on the two FET's -- namely, the upper FET must be biased so its source voltage is high enough (the lower FET drain voltage may swing too low, causing it to leave saturation). Insurance of this condition for FET's requires careful selection for the pair, or special biasing of the upper FET gate, increasing cost.

The cascode circuit can also be built using bipolar transistors, or MOSFETs, or even one FET (or MOSFET) and one BJT. In the latter case, the BJT must be the upper transistor; otherwise, the (lower) BJT will always saturate (unless extraordinary steps are taken to bias it).

Advantages

The cascode arrangement offers high gain, high slew rate, high stability, and high input impedance. The parts count is very low for a two-transistor circuit.

Disadvantages

The cascode circuit requires two transistors and requires a relatively high supply voltage. For the two-FET cascode, both transistors must be biased with ample VDS in operation, imposing a lower limit on the supply voltage.

Dual-gate version

A dual-gate MOSFET often functions as a "one-transistor" cascode. Common in the front ends of sensitive VHF receivers, a dual-gate MOSFET is operated as a common-source amplifier with the primary gate (usually designated "gate 1" by MOSFET manufacturers) connected to the input and the 2nd gate grounded (bypassed). Internally, there is one channel covered by the two adjacent gates; therefore, the resulting circuit is electrically a cascode composed of two FETs, the common lower-drain-to-upper-source connection merely being that portion of the single channel that lies physically adjacent to the border between the two gates.

Other applications

With the rise of integrated circuits, transistors have become "cheap" in terms of silicon die area. In MOSFET technology especially, cascoding can be used in current mirrors to create relatively "constant" current sources with high output impedances.

A modified version of the cascode can also be used as a modulator, particularly for amplitude modulation. The upper device supplies the audio signal, and the lower is the RF amplifier device.

Two-port parameters

The cascode configuration can be represented as a simple voltage amplifier (or more accurately as a g-parameter two-port network) by using its input impedance, output impedance, and voltage gain. These parameters are related to the corresponding g-parameters below. [ In the g-parameter two-port, "g12" is the reverse current gain. When no such feedback occurs, "g12 = 0" and the network is called unilateral.] Other useful properties not considered here are circuit bandwidth and dynamic range.

BJT Cascode: low-frequency small-signal parameters cite book
author=Gray "et al."
title=pp. 206-208
isbn=0471321680
url=http://worldcat.org/isbn/0471321680
]

The idealized small-signal equivalent circuit can be constructed for the circuit in figure 2 by replacing the current sources with open-circuits and the capacitors with short circuits, assuming they are large enough to act as short-circuits at the frequencies of interest. The BJTs can be represented in the small-signal circuit by the hybrid-pi model.

MOSFET Cascode: low-frequency small-signal parameters cite book
author=Paul R. Gray, Paul J. Hurst, Stephen H. Lewis, Robert G. Meyer
title=Analysis and Design of Analog Integrated Circuits
year= 2001
page=pp. 208-211
edition=Fourth Edition
publisher=Wiley
location=New York
isbn=0471321680
url=http://worldcat.org/isbn/0471321680
]

Similarly the small-signal parameters can be derived for the MOSFET version, also replacing the MOSFET by its hybrid-pi model equivalent. This derivation can be simplified by noting that the MOSFET gate current is zero, so the small-signal model for the BJT becomes that of the MOSFET in the limit of zero base current::: I_B o 0 Arr r_pi = egin{matrix} frac {V_T} {I_B} end{matrix} o infty ,where "VT" is the .

The combination of factors "gmrO" occurs often in the above formulas, inviting further examination. For the bipolar transistor this product is (see hybrid-pi model):

::g_m r_O = egin{matrix} frac {I_C} {V_T} frac {V_A +V_{CE {I_C} end{matrix} = egin{matrix} frac {V_A +V_{CE{V_T} end{matrix} .

In a typical discrete bipolar device the Early voltage "VA" ≈ 100 V and the thermal voltage near room temperature is "VT" ≈ 25 mV, making "gmrO" ≈ 4000, a rather large number. From the article on hybrid-pi model, we find for the MOSFET in the active mode:

::g_m r_O = egin{matrix} frac {2I_D} {V_{GS}-V_{th frac {1/lambda +V_{DS {I_D} end{matrix} = egin{matrix} frac {2(1/lambda +V_{DS})}{V_{GS}-V_{th end{matrix}

At the 65 nanometer technology node, "ID" ≈ 1.2 mA/μ of width, supply voltage is "VDD" = 1.1 V; "Vth" ≈ 165 mV, and "Vov = VGS-Vth ≈ 5%VDD" ≈ 55 mV. Taking a typical length as twice the minimum, "L" = 2 "Lmin" = 0.130 μm and a typical value of λ ≈ 1/(4 V/μm "L"), we find 1/λ ≈ 2 V, and "gmrO" ≈ 110, still a large value.cite book
author=R. Jacob Baker
title=CMOS Circuit Design, Layout, and Simulation, Revised Second Edition
year= 2008
pages=pp. 297-301
publisher=Wiley-Interscience & IEEE Press
location=New York
isbn=978-0-470-22941-5
url=http://worldcat.org/isbn/0-471-70055-X
] cite book
author=W. M. C. Sansen
title=Analog Design Essentials
year= 2006
page=§0124, p. 13
publisher=Springer
location=Dordrecht
isbn=0-387-25746-2
url=http://worldcat.org/isbn/0387257462
] The point is that because "gmrO" is large almost regardless of the technology, the tabulated gain and the output resistance for both the MOSFET and the bipolar cascode are very large. That fact has implications in the discussion that follows.

Low frequency design

The g-parameters found in the above formulas can be used to construct a small-signal voltage amplifier with the same gain, input and output resistance as the original cascode (an equivalent circuit). This circuit applies only at frequencies low enough that the transistor parasitic capacitances do not matter. The figure shows the original cascode (top panel) and the equivalent voltage amplifier or g-equivalent two-port (bottom panel). The equivalent circuit allows easier calculations of the behavior of the circuit for different drivers and loads. In the figure a Thévenin equivalent voltage source with Thévenin resistance "RS" drives the amplifier, and at the output a simple load resistor "RL" is attached. Using the equivalent circuit, the input voltage to the amplifier is (see article on voltage division):::{upsilon}_{in} = {upsilon}_s egin{matrix} frac {R_{in{R_S + R_{in end{matrix}, which shows the importance of using a driver with resistance "RS << Rin" to avoid attenuation of the signal entering the amplifier. From the above amplifier characteristics, we see that "Rin" is infinite for the MOSFET cascode, so no attenuation of input signal occurs in that case. The BJT cascode is more restrictive because "Rin = r&pi;2".

In a similar fashion, the output signal from the equivalent circuit is::{upsilon}_{out} = A_v {upsilon}_{in} egin{matrix} frac {R_{L{R_L + R_{out end{matrix},

In low frequency circuits, a high voltage gain typically is desired, hence the importance of using a load with resistance "RL >> Rout" to avoid attenuation of the signal reaching the load. The formulas for "Rout" can be used either to design an amplifier with a sufficiently small output resistance compared to the load or, if that cannot be done, to decide upon a modified circuit, for example, to add a voltage follower that matches the load better.

The earlier estimate showed that the cascode output resistance is very large. The implication is that many load resistances will not satisfy the condition "RL >> Rout". (An important exception is driving a MOSFET as load, which has infinite low frequency input impedance.) However, the failure to satisfy the condition "RL >> Rout" is not catastrophic because the cascode gain also is very large. If the designer is willing, the large gain can be sacrificed to allow a low load resistance; for "RL" << "Rout" the gain simplifies as follows:::{upsilon}_{out} = A_v {upsilon}_{in} egin{matrix} frac {R_{L{R_L + R_{out approx A_v {upsilon}_{in} frac {R_{L{R_{out = frac {A_v }{R_{out {upsilon}_{in} R_L approx -g_{m2} R_L {upsilon}_{in}end{matrix}. This gain is the same as that for the input transistor acting alone. Thus, even sacrificing gain the cascode produces the same gain as the single-transistor transconductance amplifier, but with wider bandwidth.

Because the amplifiers are wide bandwidth, the same approach can determine the bandwidth of the circuit when a load "capacitor" is attached (with or without a load resistor). The assumption needed is that the load capacitance is large enough that it controls the frequency dependence, and bandwidth is "not" controlled by the neglected parasitic capacitances of the transistors themselves.

High frequency design

At high frequencies, the parasitic capacitances of the transistors (gate-to-drain, gate-to-source, drain-to body, and bipolar equivalents) must be included in the hybrid pi models to obtain an accurate frequency response. The design goals also differ from the emphasis on overall high gain as described above for low-frequency design. In high frequency circuits, impedance matching typically is desired at the input and output of the amplifier to eliminate signal reflections and maximize power gain. In the cascode, the isolation between the input and output ports still is characterized by a small reverse transmission term g12, making it easier to design matching networks because the amplifier is approximately unilateral.

Footnotes and references

ee also

*Common source
*Common emitter


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • cascode — ● cascode nom masculin Montage électronique amplificateur dans lequel le collecteur d un premier transistor transmet la tension amplifiée à l émetteur du transistor suivant, dont la base est mise à la masse …   Encyclopédie Universelle

  • Cascode — Montage cascode Le montage cascode, à ne pas confondre avec le montage en cascade, associe deux transistors de caractéristiques différentes (ils peuvent être tous deux bipolaires, tous deux à effet de champ, ou un de chaque). Chaque transistor… …   Wikipédia en Français

  • cascode — kaskodinė grandinė statusas T sritis radioelektronika atitikmenys: angl. cascode; cascode circuit vok. Kaskodenschaltung, f rus. каскодная схема, f pranc. cascode, f …   Radioelektronikos terminų žodynas

  • Cascode Voltage Switch Logic — refers to a CMOS type logic family which is designed for certain advantages. It requires mainly nMOS transistors to implement the logic using true and complementary input signals, and also needs 2 pMOS transistors at the top to pull one of the… …   Wikipedia

  • cascode circuit — kaskodinė grandinė statusas T sritis radioelektronika atitikmenys: angl. cascode; cascode circuit vok. Kaskodenschaltung, f rus. каскодная схема, f pranc. cascode, f …   Radioelektronikos terminų žodynas

  • cascode amplifier — kaskodinis stiprintuvas statusas T sritis fizika atitikmenys: angl. cascode amplifier vok. Kaskodenverstärker, m; Kaskodeverstärker, m rus. каскодный усилитель, m pranc. amplificateur en cascode, m …   Fizikos terminų žodynas

  • cascode — …   Useful english dictionary

  • Montage Cascode — Le montage cascode, à ne pas confondre avec le montage en cascade, associe deux transistors de caractéristiques différentes (ils peuvent être tous deux bipolaires, tous deux à effet de champ, ou un de chaque). Chaque transistor apporte dans le… …   Wikipédia en Français

  • Montage cascode — Le montage cascode, à ne pas confondre avec le montage en cascade, associe deux transistors de caractéristiques différentes (ils peuvent être tous deux bipolaires, tous deux à effet de champ, ou un de chaque). Chaque transistor apporte dans le… …   Wikipédia en Français

  • amplificateur en cascode — kaskodinis stiprintuvas statusas T sritis fizika atitikmenys: angl. cascode amplifier vok. Kaskodenverstärker, m; Kaskodeverstärker, m rus. каскодный усилитель, m pranc. amplificateur en cascode, m …   Fizikos terminų žodynas

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”