Vector control (motor)

Vector control (motor)

Vector control (also called Field Oriented Control, FOC) is one method used in variable frequency drives to control the torque (and thus finally the speed) of three-phase AC electric motors by controlling the current fed to the machine.

Method

The Stator phase currents are measured and converted into a corresponding complex (space) vector. This current vector is then transformed to a coordinate system rotating with the rotor of the machine. For this the rotor position has to be known. Thus at least speed measurement is required, the position can then be obtained by integrating the speed.

Then the rotor flux linkage vector is estimated by multiplying the stator current vector with magnetizing inductance Lm and low-pass filtering the result with the rotor no-load time constant Lr/Rr, that is the ratio of the rotor inductance to rotor resistance.

Using this rotor flux linkage vector the stator current vector is further transformed into a coordinate system where the real x-axis is aligned with the rotor flux linkage vector.

Now the real x-axis component of the stator current vector in this rotor flux oriented coordinate system can be used to control the rotor flux linkage and the imaginary y-axis component can be used to control the motor torque.

Typically PI-controllers are used to control these currents to their reference values. However, bang-bang type current control, that gives better dynamics, is also possible.

With PI-controllers the outputs of the controllers are the x-y components of the voltage reference vector for the stator. Usually due to the cross coupling between the x- and y-axes a decoupling term is further added to the controller output in order to improve the control performance when big and rapid changes in speed, current and flux linkage take place. Usually the PI-controller also needs low-pass filtering of either the input or output of the controller in order to prevent the current ripple due to transistor switching from being amplified excessively and unstabilizing the control. Unfortunately, the filtering also limits the dynamics of the control system. Thus quite high switching frequency (typically more than 10 kHz) is required in order to allow only minimum filtering for high performance drives such as servo drives.

Next the voltage references are first transformed to the stationary coordinate system (usually through rotor d-q coordinates) and then fed into a modulator that using one of the many Pulse Width Modulation (PWM) algorithms defines the required pulse widths of the stator phase voltages and controls the transistors (usually IGBTs) of the inverter according to these.

This control method implies the following properties of the control:

* Speed or position measurement or some sort of estimation is needed
* Torque and flux can be changed reasonably fast, in less than 5-10 milliseconds, by changing the references
* The step response has some overshoot if PI control is used
* The switching frequency of the transistors is usually constant and set by the modulator
* The accuracy of the torque depends on the accuracy of the motor parameters used in the control. Thus large errors due to for example rotor temperature changes often are encountered.
* Reasonable processor performance is required, typically the control algorithm has to be calculated at least every millisecond.

Although the vector control algorithm is more complicated than the Direct Torque Control (DTC), the algorithm is not needed to be calculated as frequently as the DTC algorithm. Also the current sensors need not be the best in the market. Thus the cost of the processor and other control hardware is lower making it suitable for applications where the ultimate performance of DTC is not required.

History

Vector control was patented by Felix Blaschke in US patent|3824437 filed originally on August 14, 1969 in Germany while he worked for Siemens.

Another important contemporary publication about the same topic was

* Karl Hasse: Zur Dynamik drehzahlgeregelter Antriebe mit stromrichtergespeisten Asynchron-Kurzschlußläufermotoren. Dissertation, TH Darmstadt, 1969.

In the Blaschke's patent the rotor flux linkage was calculated from the measured air-gap magnetic field. Thus this method is called direct rotor oriented vector control. However, in order to be able to use standard induction machines, method to estimate the rotor flux linkage from the measured stator currents, as proposed by Hasse, is more practical. Versions based on flux estimation instead of measuring are called indirect rotor oriented vector controls. An early review of the possible alternatives was published in the paper:

* Blaschke, F., Böhm, K.: Verfahren der Felderfassung bei der Regelung stromrichtergespeister Asynchronmaschinen. IFAC Symposium: Control in Power Electronics and Electrical Drives, Duesseldorf, October 7 – 9, 1974, Proceedings Vol I, pp. 635...649.

Vector control has later been dealt with in numerous publications. Several methods have been developed to make possible the operation without speed or position sensor. Also methods to estimate the rotor time constant and other parameters have been presented. One good book dealing with these issues is:

* Peter Vas: Sensorless Vector and Direct Torque Control, Oxford University Press, 1998, ISBN 0-19-856465-1

In addition to induction machines, the vector control has also been applied to synchronous machines and doubly fed machines.

After the major Siemens' patents expired in the end of 80's and beginning of 90's, many other manufacturers begin to use this method in their products making this the de facto standard in demanding motor control applications the only alternative being the Direct Torque Control (DTC) developed by ABB.

ee also


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Vector control — For vector control of induction motors, see Motor controller Vector control is any method to limit or eradicate the mammals, birds or arthropods, insects which transmit disease pathogens. The most frequent type of vector control is mosquito… …   Wikipedia

  • Motor controller — A motor controller is a device or group of devices that serves to govern in some predetermined manner the performance of an electric motor.[1] A motor controller might include a manual or automatic means for starting and stopping the motor,… …   Wikipedia

  • Motor soft starter — Examples of motor soft starters [1] A motor soft starter is a device used with AC electric motors to temporarily reduce the load and torque in the powertrain of the motor during startup. This reduces the mechanical stress on the motor and shaft,… …   Wikipedia

  • Direct torque control — (DTC) is one method used in variable frequency drives to control the torque (and thus finally the speed) of three phase AC electric motors. This involves calculating an estimate of the motor s magnetic flux and torque based on the measured… …   Wikipedia

  • Vector Motors — Infobox Company company name = Vector Motors Corporation company company type = Private foundation = 1971 location = Wilmington, California key people = Gerald Wiegert Chairman CEO industry = Automotive products = The Vector Vector W2 Vector W8… …   Wikipedia

  • Control vectorial — Este artículo o sección necesita referencias que aparezcan en una publicación acreditada, como revistas especializadas, monografías, prensa diaria o páginas de Internet fidedignas. Puedes añadirlas así o avisar …   Wikipedia Español

  • Control theory — For control theory in psychology and sociology, see control theory (sociology) and Perceptual Control Theory. The concept of the feedback loop to control the dynamic behavior of the system: this is negative feedback, because the sensed value is… …   Wikipedia

  • Control unit — A control unit in general is a central (or sometimes distributed but clearly distinguishable) part of the machinery that controls its operation, provided that a piece of machinery is complex and organized enough to contain any such unit. One… …   Wikipedia

  • Brushless DC electric motor — A microprocessor controlled BLDC motor powering a micro remote controlled airplane. This external rotor motor weighs 5 grams, consumes approximately 11 watts (15 millihorsepower) and produces thrust of more than twice the weight of the plane …   Wikipedia

  • Electric motor — For other kinds of motors, see motor (disambiguation). For a railroad electric engine, see electric locomotive. Various electric motors. A 9 volt PP3 transistor battery is in the center foreground for size comparison. An electric motor converts… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”