Automatic dependent surveillance-broadcast


Automatic dependent surveillance-broadcast

Automatic dependent surveillance-broadcast (ADS-B) is a cooperative surveillance technique for air traffic control and related applications. An ADS-B-out equipped aircraft determines its own position using a global navigation satellite system and periodically broadcasts this position and other relevant information to potential ground stations and other aircraft with ADS-B-in equipment.ADS-B can be used over several different data link technologies, including Mode-S Extended Squitter (1090 ES), VHF data link (VDL Mode 4), and Universal Access Transceivers (UAT).

ADS-B provides accurate information and frequent updates to airspace users and controllers, and hence supports improved use of airspace, reduced ceiling/visibility restrictions, improved surface surveillance, and enhanced safety, for example through conflict management.

Under ADS-B, a vehicle periodically broadcasts its own state vector and other information without knowing what other vehicles or entities might be receiving it, and without expectation of an acknowledgment or reply. ADS-B is "automatic" in the sense that no pilot or controller action is required for the information to be issued. It is "dependent surveillance" in the sense that the surveillance-type information so obtained depends on the suitable navigation and broadcast capability in the source vehicle.cite book | date=June 25 2002 | title=Minimum Aviation System Performance Standards for Automatic Dependent Surveillance-Broadcast (ADS-B) | publisher=RTCA, Inc| id=DO-242A ]

A similar solution is the Automatic Identification System (AIS), a system used by ships and Vessel Traffic Services.

Theory of operation

ADS-B consists of three components:
*A transmitting subsystem that includes message generation and transmission functions at the source, e.g. airplane.
*The transport protocol, e.g. VHF(VDL mode 2 or 4) or 1090ES.
*A receiving subsystem that includes message reception and report assembly functions at the receiving destination, e.g. other airplanes, vehicle or ground system.

The source of the state vector and other transmitted information as well as user applications are not considered to be part of the ADS-B system.

Relationship to surveillance radar

Radar directly measures the range and bearing of an aircraft. Bearing is measured by the position of the rotating radar antenna when it receives a response to its interrogation from the aircraft, and range is measured by the time it takes for the radar to receive the interrogation response.

The antenna beam becomes wider as the aircraft gets further away, making the position information less accurate. Additionally, detecting changes in aircraft velocity requires several radar sweeps that are spaced several seconds apart. In contrast, a system using ADS-B creates and listens for periodic position and intent reports from aircraft. These reports are generated based on e.g the global positioning system (GPS)and distributed via VHF radio or Mode S transponders, meaning integrity of the data is no longer susceptible to the position of the aircraft or the length of time between radar sweeps.cite press release
title=FAA Announces Automatic Dependent Surveillance-Broadcast Architecture
publisher=FAA Office of Public Affairs
date=July 1 2002
url=http://www.faa.gov/asd/ads-b/press.htm
ID=APA 27-02
accessdate = 2007-05-02
]

Primary Surveillance Radar does not require any cooperation from the aircraft. It is robust in the sense that surveillance outage failure modes are limited to those associated with the ground radar system. Secondary Surveillance Radar depends on active replies from the aircraft. Its failure modes include the transponder aboard the aircraft. Typical ADS-B aircraft installations use the output of the navigation unit for navigation and for cooperative surveillance, introducing a common failure mode that must be accommodated in air traffic surveillance systems.

Today's ATM systems does not rely on coverage by a single radar only. Instead a multiradar picture is presented via the ATM system's display to the controller ( ATCO). This improves the quality of the reported position of the airplane, provides a measure of redundancy, and makes it possible to verify the output of the different radars against others. This verification can also use sensor data from other technologies, such as ADS-B and multilateration.

Relationship to ADS-A/ADS-C

There are two commonly recognized types of ADS for aircraft applications:
*ADS-Addressed (ADS-A), also known as ADS-Contract (ADS-C), and
*ADS-Broadcast (ADS-B).

ADS-B is inherently different from ADS-A, in that ADS-A is based on a negotiated one-to-one peer relationship between an aircraft providing ADS information and a ground facility requiring receipt of ADS messages. For example, ADS-A reports are employed in the Future Air Navigation System (FANS) using the Aircraft Communication Addressing and Reporting System (ACARS) as the communication protocol. During flight over areas without radar coverage (e.g., oceanic, polar), reports are periodically sent by an aircraft to the controlling air traffic region.

The transmission delay caused by protocol, satellites, etc., is so long that it requires "huge" separation between airplanes. The cost using the satellite channel leads to less frequent updates. Another drawback is that no other aircraft can benefit from the transmitted information.

Relationship to other broadcast services

The ADS-B link can be used to provide other broadcast services, such as TIS-B and FIS-B (see below).

Another potential aircraft-based broadcast capability is to transmit aircraft measurements of meteorological data.

Benefits of ADS-B

ADS-B is intended to increase safety and efficiency. Safety benefits include:cite paper | author=Scardina, John | title=Overview of the FAA ADS-B Link Decision | publisher=Federal Aviation Administration | date=June 7 2002 | url=http://www.faa.gov/asd/ads-b/06-07-02_ADS-B-Overview.pdf]
*Improved visual acquisition especially for general aviation under visual flight rules (VFR).
*Reduced runway incursions of the airport surface.

ADS-B enables increased capacity and efficiency by supporting:
*Enhanced visual approaches
*Closely spaced parallel approaches
*Reduced spacing on final approach
*Reduced aircraft separations
*Enhanced operations in high altitude airspace for the incremental evolution of the "free flight" concept
*Surface operations in lower visibility conditions
*Near visual meteorological conditions (VMC) capacities throughout the airspace in most/all weather conditions
*Improved ATC services in non-radar airspace

However, although ADS-B is suitable for surveillance of remote areas where the siting of radars is difficult, some ATC providers are not yet convinced that it is currently suitable for use in high traffic volume areas, such as in UK and Northern European airspace. Changing from conventional SSR to ADS-B would also require investment in ATC infrastructure, something which many European providers may be unwilling to sanction. Furthermore, ADS-B provides no ground verification of the accuracy of the information provided by aircraft and this could have adverse security implications. [ [http://www.caa.co.uk/docs/7/DAP_SSM_Mode_S_SSR_Factsheet.pdf CAA Mode S Fact Sheet ] ]

Traffic information services-broadcast (TIS-B)

TIS-B supplements ADS-B air-to-air services to provide complete situational awareness in the cockpit of all traffic known to the ATC system. TIS-B is an important service for an ADS-B link in airspace where not all aircraft are transmitting ADS-B information. The ground TIS-B station transmits surveillance target information on the ADS-B data link for unequipped targets or targets transmitting only on another ADS-B link.

TIS-B uplinks are derived from the best available ground surveillance sources:
*ground radars for primary and secondary targets
*multi-lateration systems for targets on the airport surface
*ADS-B systems for targets equipped with a different ADS-B link

Multilink gateway service

The multilink gateway service is a companion to TIS-B for achieving interoperability in low altitude terminal airspace. In some airspaces, aircraft that primarily operate in high altitude airspace are equipped with 1090ES, and aircraft operating primarily in low altitude airspace are equipped with UAT. These aircraft cannot directly share air-to-air ADS-B data. In terminal areas, where both types of ADS-B link are in use, ADS-B/TIS-B ground stations use ground-to-air broadcasts to relay ADS-B reports received on one link to aircraft using the other link.

Flight information services-broadcast (FIS-B)

FIS-B provides weather text, weather graphics, NOTAMs, ATIS, and similar information. FIS-B is inherently different from ADS-B in that it requires sources of data external to the aircraft or broadcasting unit, and has different performance requirements such as periodicity of broadcast.

In the US, FIS-B services will be provided over the UAT link in areas that have a ground surveillance infrastructure.

ADS-B physical layer

Three link solutions are being proposed as the physical layer for relaying the ADS-B position reports:
*1090 MHz Mode S Extended Squitter (ES),
*Universal Access Transceiver (UAT) and
*VHF Digital Link (VDL) Mode 4.

A comparison of these link solutions was made in Gatwick/Heathrow in year 2002 for the Eurocontrol ADS programme. [cite web
title = ADS-B Surface Surveillance Trials 2002
url = http://www.gpc.se/vdlcompare1/heathrowrep.pdf
publisher = Eurocontrol/NATS
date = 2002
accessdate = 2008-09-10 |format=PDF
]

1090ES

In 2002, the FAA has announced a dual link decision using 1090 MHz ES and UAT as mediums for the ADS-B system in the United States. The 1090 MHz extended squitter ADS-B link for air carrier and private/commercial operators of high performance aircraft, and Universal Access Transceiver (UAT) ADS-B link for the typical general aviation user.

Europe has not officially chosen a physical layer for ADS-B. A number of technologies are in use. However, the influential Eurocontrol CASCADE program uses 1090ES exclusively. [cite web
title = CASCADE Frequently Asked Questions
url = http://www.eurocontrol.int/cascade/public/faq/faq.html#qa06
publisher = Eurocontrol
date = July 24 2006
accessdate = 2007-05-15
]

With 1090ES, the existing Mode S transponder (TSO C-112 or a stand alone 1090 MHz transmitter) supports a message type known as the extended squitter (ES) message. It is a periodic message that provides position, velocity, heading, time, and, in the future, intent. The basic ES does not offer intent since current flight management systems do not provide such data – called trajectory change points. To enable an aircraft to send an extended squitter message, the transponder is modified (TSO C-166A) and aircraft position and other status information is routed to the transponder. ATC ground stations and TCAS-equipped aircraft already have the necessary 1090 MHz (Mode S) receivers to receive these signals, and would only require enhancements to accept and process the additional Extended Squitter information. 1090ES does not support FIS-B service. Fact|date=May 2007

Universal access transceiver

The UAT system is specifically designed for ADS-B operation. UAT has lower cost and greater uplink capacity than 1090ES. Although 978 MHz resides in the TACAN assigned portion of the aeronautical spectrum, in the US 978 is used for transmission of airborne ADS-B reports and for broadcast of ground-based aeronautical information. UAT users have access to ground-based aeronautical data and can receive reports from proximate traffic (FIS-B and TIS-B). TIS-B provides reports for proximate aircraft through a multilink gateway service that provides ADS-B reports for 1090ES equipped aircraft and non-ADS-B equipped Radar traffic.

VDL mode 4

The VDL Mode 4 system could utilize one or more of the existing aeronautical VHF frequencies as the radio frequency physical layer for ADS-B transmissions.

VDL Mode 4 uses a protocol (STDMA, invented by Swedish Håkan Lans in 1988) that allows it to be self-organizing, meaning no master ground station is required.

In November 2001 this protocol was published by ICAO as a global standard.

This medium is best used for short message transmissions between a large number of users.

VDL Mode 4 systems required by airlines in Europe as a mean for more efficient ATC service [cite web
title = Airlines propose ADS-B implementation sites
url = http://www.eurocontrol.int/corporate/gallery/content/public/docs/pdf/pressreleases/2008/080221_ADS-B%20Deployment_Final.pdf
date = 2008-02-21
accessdate = 2009-09-10|format=PDF
] .

ADS-B supported applications

The ADS-B data link supports a number of airborne and ground applications. Each application has its own operational concepts, algorithms, procedures, standards, and user training.

Cockpit display of traffic information

A Cockpit Display of Traffic Information (CDTI) is a generic display that provides the flight crew with surveillance information about other aircraft, including their position. Traffic information for a CDTI may be obtained from one or multiple sources, including ADS-B, TCAS, and TIS-B. Direct air-to-air transmission of ADS-B messages supports display of proximate aircraft on a CDTI.

In addition to traffic based on ADS-B reports, a CDTI function might also display current weather conditions, terrain, airspace structure, obstructions, detailed airport maps, and other information relevant to the particular phase of flight.

Airborne collision avoidance

ADS-B is seen as a valuable technology to enhance ACAS operation. Incorporation of ADS-B can provide benefits such as:
*Decreasing the number of active interrogations required by ACAS, thus increasing effective range in high density airspace.
*Reducing unnecessary alarm rate by incorporating the ADS-B state vector, aircraft intent, and other information.
*Use of the ACAS display as a CDTI, providing positive identification of traffic.
*Extending collision avoidance below 1000 feet above ground level, and detecting runway incursions.

Eventually, the ACAS function may be provided based solely on ADS-B, without requiring active interrogations of other aircraft transponders.

Conflict management

ATS conformance monitoring

Other applications

Other applications that may benefit from ADS-B include:
*Improved search and rescue
*Enhanced flight following
*Lighting control and operation
*Airport ground vehicle and aircraft rescue and firefighting vehicle operational needs
*Altitude height keeping performance measurements
*General aviation operations control

U.S. implementation timetable

The U.S. FAA ADS-B implementation is broken into three segments each with a corresponding time line. Ground segment implementation and deployment is expected to begin in 2009 and be completed by 2013 throughout the National Airspace System. Airborne equipage is user driven and is expected to be completed both voluntarily based on perceived benefits and through regulatory actions (Rulemaking) by the FAA. The cost to equip with ADS-B Out capability is relatively small and would benefit the airspace with surveillance in areas not currently served by radar. The FAA intends to provide similar service within the NAS to what radar is currently providing (5NM en route and 3NM terminal radar standards) as a first step to implementation. However, ADS-B In capability is viewed as the most likely way to improve NAS throughput and enhance capacity.

FAA segment 1 (2006-2009)

ADS-B deployment and voluntary equipage, along with rule making activities. Pockets of development will exploit equipment deployment in the areas that will provide proof of concept for integration to ATC automation systems deployed in the NAS.cite web
url = http://www.faa.gov/about/office_org/headquarters_offices/ato/service_units/enroute/surveillance_broadcast/schedule/
title = Schedule
work = Surveillance and Broadcast Services
publisher = FAA
]

FAA segment 2 (2010-2014)

ADS-B ground stations will be deployed throughout the NAS, with an In-Service Decision due in the 2012-13 time frame. Completed deployment will occur in the 2013-2014 time frame. Equipage is expected to begin after the proposed rule is finalized in around 2010:

*Airport Situational Awareness – A combination of detailed airport maps, airport multilateration systems, ADS-B systems and enhanced aircraft displays have the potential to significantly improve Final Approach and Runway Occupancy Awareness (FAROA). Fact|date=May 2007
*Oceanic In-trail – ADS-B may provide enhanced situational awareness and safety for Oceanic In-trail maneuvers as additional aircraft become equipped. Fact|date=May 2007
*Gulf of Mexico – In the Gulf of Mexico, where ATC radar coverage is incomplete, the FAA is locating ADS-B (1090 MHz) receivers on oil rigs to relay information received from aircraft equipped with ADS-B extended squitters back to the Houston Center to expand and improve surveillance coverage. Fact|date=May 2007

FAA segment 3 (2015-2020)

ADS-B In equipage will be based on user perceived benefit, but is expected to be providing increased situational awareness and efficiency benefits within this segment. Those aircraft who choose to equip in advance of any mandate will see benefits associated with preferential routes and specific applications. Limited radar decommissioning will begin in the time frame with an ultimate goal of a 50% reduction in the Secondary Surveillance Radar infrastructure. Fact|date=May 2007

Non FAA implementations

*Use of ADS-B and CDTI may allow decreased approach spacing at certain airports to improve capacity during reduced-visibility operations when visual approach operations would normally be terminated (eg. ceilings less than MVA +500).
*United States
**Cargo Airline Association - Cargo carriers, notably United Parcel Service (UPS), operating at their hub airports operate largely at night. Much of the benefit to these carriers is envisioned through merging and spacing the arriving and departing traffic to a more manageable flow. More environmentally friendly and efficient area navigation (RNAV) descent profiles, combined with CDTI, may allow crews to eventually aid controllers with assisted visual acquisition of traffic and limited cockpit-based separation of aircraft. The benefits to the carrier are fuel and time efficiencies associated with idle descent and shorter traffic patterns than typical radar vectoring allows. Fact|date=May 2007
**Embry-Riddle Aeronautical University - ERAU has equipped their training aircraft at its two main campuses in Florida and Arizona with UAT ADS-B capability as a situational safety enhancement. The University has been doing this since May 2003, making it the first use in general aviation. [cite web
title = Embry-Riddle Becomes First in General Aviation to Use Revolutionary ADS-B System
url = http://www.erau.edu/er/newsmedia/newsreleases/2003/track.html
date = 2003-05-13
accessdate = 2007-07-27
] With the addition of the G1000 to their fleet in 2006, ERAU became the first fleet to combine a glass cockpit with ADS-B. [cite web
title = Embry-Riddle Fleet First to Combine Glass Cockpit and ADS-B
url = http://www.skycontrol.net/reports/embry-riddle-fleet-first-to-combine-glass-cockpit-and-ads-b/
date = 2006-02-03
accessdate = 2007-07-27
]
**University of North Dakota - UND has received an FAA grant to test ADS-B, and has begun to outfit their Piper Warrior fleet with an ADS-B package. [cite web
title = UND Aerospace Researcher Awarded $302,459 Grant To Study Safety-Enhancing Technology
url = http://www2.und.edu/our/news/story.php?id=1962
publisher = University of North Dakota
date = 2006-11-17
accessdate = 2007-05-03
]
*Australia
**Burnett Basin Operational Trial - Successfully concluded in June 2006, the trial installed a single ADS-B ground station near Bundaberg, equipped a number of aircraft with ADS-B avionics, and modified an operational air traffic management system to process and display ADS-B information. [cite web
title = Burnett Basin Operational Trial of ADSB
url = http://www.airservicesaustralia.com/pilotcentre/projects/adsb/burnettbasin.asp
publisher = Airservices Australia
date = August 1 2006
accessdate = 2007-05-02
]
**Upper Airspace Program - A program aimed at providing near-term safety and operational benefits in high level, non-radar airspace. Includes installation of approximately 28 ADS-B ground stations, strategically located across Australia to provide air traffic surveillance above 30,000 feet in continental airspace outside of radar coverage. All sites are expected to be installed and operating by mid 2007. [cite web
title = ADS-B Upper Airspace Program (UAP)
url = http://www.airservicesaustralia.com/pilotcentre/projects/adsb/adsbuap.asp
publisher = Airservices Australia
date = September 1 2006
accessdate = 2007-05-02
]
**Australian Transition to Satellite Technology - Now in initial planning and development, this is a major, longer term program designed to make ADS-B the primary means of ground to air and air to air surveillance in Australian enroute airspace. Includes installation of additional ADS-B ground stations to provide air traffic surveillance in airspace currently covered by enroute radar facilities. Intended to lead to the decommissioning of a number of radar sites. Mandatory aircraft ADS-B equipment requirements will apply – funding options to support general aviation operators will be explored. [cite web
title = Australian Transition to Satellite Technology (ATLAS)
url = http://www.airservicesaustralia.com/pilotcentre/projects/adsb/
publisher = Airservices Australia
date = August 7 2007
accessdate = 2007-08-24
]

*Canada - Canada is planning to use ADS-B to provide coverage of its northern airspace around Hudson Bay, most of which currently has no radar coverage. ADS-B will be initially deployed in the Hudson Bay Basin in 2007–2008 and the service is expected to be later extended to cover the rest of the Canadian Arctic and eventually to the rest of Canada.cite web | title=Aviation Safety Letter
work=
url=http://www.tc.gc.ca/CivilAviation/publications/tp185/1-07/Pre-flight.htm#NAVCanada
publisher=Transport Canada, Civil Aviation
month= January | year= 2007
accessdate = 2007-05-01
] cite press release
title = NAV CANADA announces the acquisition of new surveillance technology to improve air traffic safety and customer efficiency
publisher = NAV CANADA
date = February 12 2007
url = http://www.navcanada.ca/NavCanada.asp?Language=en&Content=ContentDefinitionFilesNewsroomNewsReleases2007 r0212.xml
accessdate = 2007-05-01
]

*Sweden - LFV Group in Sweden has implemented a nationwide ADS-B network with 12 ground stations. Installation commenced during spring 2006, and the network was fully (technically) operational in 2007. An ADS-B supported system is planned for operational usage in Kiruna during spring 2009. Based on the VDL Mode 4 standards, the network of ground stations can support services for ADS-B, TIS-B, FIS-B, GNS-B (DGNSS augmentation) and Point-to-Point communication, allowing aircraft equipped with VDL 4-compliant transceivers to lower fuel consumption and reduce flight times.Fact|date=May 2007

ystem design considerations of ADS-B

A concern for any ADS-B protocol is the capacity for carrying ADS-B messages from aircraft, as well as allowing the radio channel to continue to support any legacy services. For 1090ES, each ADS-B message is composed of a pair of data packets. The greater the number of packets transmitted from one aircraft, the lesser the number of aircraft that can participate in the system, due to the fixed and limited channel data bandwidth.

System capacity is defined by establishing a criterion for what the worst environment is likely to be, then making that a minimum requirement for system capacity. For 1090ES, both TCAS and ATCRBS/MSSR are existing users of the channel. 1090ES ADS-B must not reduce capacity of these existing systems.

The FAA national program office and other International aviation regulators are addressing concerns about ADS-B [http://www.airsport-corp.com/adsb2.htm non-secure nature of ADS-B] transmissions. ADS-B messages can be used to know the location of an aircraft, and there is no means to guarantee that this information is not used inappropriately. Additionally, there are some concerns about the integrity of ADS-B transmissions. ADS-B messages can be produced, with simple low cost measures, which spoof the locations of multiple phantom aircraft to disrupt safe air travel. There is no foolproof means to guarantee integrity, but there are means to monitor for this type of activity. This problem is however similar to the usage of ATCRBS/MSSR where false signals also are potentialy dangerous (uncorrelated secondary tracks).

There are some concerns about ADS-B dependence on other systems. This paper from 2001 mentions some of the potential riscs. [cite web
title = Vulnerability accessment of the transportation infrastructure relying on GPS
url = http://www.navcen.uscg.gov/gps/geninfo/Volpe%20Slides.ppt
date = 2001-10-05
accessdate = 2008-09-16
] The riscs mentioned can be mitigated by using other sources of information, e.g. GLONASS, Galileo or multilateration.

There are some General Aviation concerns that ADS-B removes anonymity of the VFR aircraft operations. Fact|date=May 2007 The ICAO 24-bit transponder code specifically assigned to each aircraft will allow monitoring of that aircraft when within the service volumes of the Mode-S/ADS-B system. Unlike the Mode A/C transponders, there is no code "1200"/"7000", which offers casual anonymity. Mode-S/ADS-B identifies the aircraft uniquely among all in the world, sort of a MAC number in an ethernet card or the IMEI (International Mobile Equipment Identity) of a GSM phone.

Public Access to ADS-B

Currently there are no laws preventing anyone from listening to and decoding ADS-B transmissions. Like Cellular Phone however, laws can easily be implemented to make reception a crime. The ongoing debate amongst hobbyists is to display real-time activity on personal screens and then delay five minutes on networked displays. Others feel that, like GPS data, it should be freely available.

Two receivers are currently popular, although both are at the expensive end for consumer devices. The first on the market was Kinetic Avionics with their SBS-1. The second was the AirNav RadarBox. Both of these devices are designed to be used for portable operation, although many have used them in base operation. They are both supplied with a short USB cable for interface to a Windows PC, and a short coax to a small omni antenna.

Both products have specialized single-use receivers in them. Unlike most radios there is no Intermediate Frequency (IF). The ADS-B data flows from the supplied antenna through an LNA pre-amp. It is bandwidth filtered, and then the pulses are extracted using a logarithmic amplifier chip. This chip can operate directly at the ADS-B frequency of 1090 MHz. These analog pulses are then applied to a high speed analog to digital (A/D) converter (40 MHz for Kinetic, 8 MHz for AirNav) and then on to the Field-Programmable Gate Array (FPGA), where the Mode-S frames are detected. The detected Mode-S packets are then sent to the PC via a USB interface.

ADS-B technical and regulatory documents

"MASPS = Minimum Aviation System Performance Standards"
"MOPS = Minimum Operational Performance Standards"

* DO-289 - Airborne Surveillance Applications (ASA) MOPS
** High level system architecture and sub-system descriptions.
* DO-242A - ADS-B MASPS
** Describes system-wide operational use of ADS-B.
* DO-286A - TIS-B MASPS
** Describes a surveillance service that derives traffic information from ground surveillance sources, broadcasts to ADS-B equipped aircraft or surface vehicles.
* DO-260A - 1090 MOPS for ADS-B and TIS-B
** Airborne equipment characteristics / requirements for 1090 MHz Mode-S extended squitter.
** Change 1-DO-260A–PMC consideration review/approval –June 27 2006
* DO-282A - UAT MOPS
** Airborne equipment characteristics / requirements utilizing the universal access transceiver.
* DO-XXX - STP MOPS (work in progress)
** Describes a function that processes information prior to the information being broadcast by the ADS-B transmit function.
* DO-XXX - ASAS MOPS (work in progress)
** Adds additional subsystems necessary to fully implement AirborneSurveillance Applications:
*** Airborne Surveillance and Separation Assurance Processing (ASSAP)
*** Cockpit Display of Traffic Information (CDTI)
* DO-259 - CDTI Application Description
** Provides initial CDTI applications descriptions.

ee also

*DO-212 Minimal Operational Performance Standards for Airborne Automatic Dependent Surveillance (ADS) Equipment
*NextGen (US)
*SESAR (Europe)
*TCAS
*FLARM
*PCAS
*ASDE-X
*Free flight

References

External links

* [http://www.adsb.gov Official FAA ADS-B Website]
* [http://www.airsport-corp.com/adsb2.htm ADS-B ... Terrorist's Dream, Security's Nightmare]
* [http://www.mitrecaasd.org/library/documents/atm2003_paper84.pdf Commercial Aviation Accidents Before and During the Alaska Capstone Implementation of ADS-B, FIS-B, Terrain Situational Awareness, and Expanded IFR Infrastructure]
* [http://www.flarm.com Flarm, a simple low-range ADS-B concept implementation]
* [http://www.nup.nu NUP II Project]
* [http://www.nup.nu/nup2plus/ NUP II Plus]
* [http://www.egoa.se Enhanced General Aviation by ADS-B]
* [http://www.adsmedup.it/ ADS-MEDUP Project]
* [http://www.eurocontrol.int/cascade/public/subsite_homepage/homepage.html Eurocontrol CASCADE Programme]
* [http://www.eurocae.org/ European Organisation for Civil Aviation Equipment]
*: A publicly accessible database of aircraft registrations, SELCAL codes and ICAO24 address codes. The database is not complete and rellies on user feedback to remain up to date.
* [http://www.kloth.net/radio/icao24alloc.php ICAO Annex 10 Volume III Chapter 9. Aircraft Addressing System]
* [http://www.bas.uk.net/data6.html Overview of collision avoidance systems]
* [http://www.jpdo.aero Joint Planning & Development Office]
* [http://www.adsb.gov Safe Flight 21 ADS-B Projects]
* [http://www.faa.gov/about/office_org/headquarters_offices/arc/programs/capstone/ Capstone ADS-B Project]
* [http://www.airservicesaustralia.com/pilotcentre/projects/adsb/ Airservices Australia ADS-B Programs]
* [http://www.aopa.org/whatsnew/newsitems/2007/070118ads-b.html AOPA News Archive]
* [http://www.kinetic-avionics.co.uk/sbs-1.php Kinetic Avionics SBS-1]
* [http://www.airnavsystems.com/RadarBox/index.html AirNav RadarBox]
* [http://www.faa.gov/about/office_org/headquarters_offices/arc/programs/capstone/media/GDL90_Public_ICD_RevA.PDF Capstone Public Interface for Garmin GDL-90]
* [http://www.airnavsystems.com/shiptrax/ AirNav Systems Ship Tracking Software]

Commercial implementations of ADS-B

* [http://www.l-3com.com/products-services/docoutput.aspx?id=543 ACSS' SafeRouteTM ADS-B Solutions for Approach and Taxi, used by UPS]
* [http://www.gtwn.net/~keith.peshak/AIS-P.htm AIS-P]
* [http://www.comsoft.de/html/atc/products/adsb/index.htm Quadrant ADS-B] Sensors


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Automatic dependent surveillance-broadcast — L Automatic dependent surveillance broadcast (ADS B) est un nouveau système de surveillance coopératif pour le contrôle du trafic aérien et d autres applications connexes. Un avion équipé de l ADS B détermine sa position par un système de… …   Wikipédia en Français

  • Automatic Dependent Surveillance - Broadcast — Automatic Dependent Surveillance (ADS), zu deutsch etwa Automatische bordabhängige Überwachung, ist ein System der Flugsicherung zur Anzeige der Flugbewegungen im Luftraum. Die Luftfahrzeuge bestimmen selbständig ihre Position, beispielsweise… …   Deutsch Wikipedia

  • ADS-B Automatic dependent surveillance-broadcast — Связать? ADS B (англ. Automatic dependent surveillance broadcast) Содержание 1 …   Википедия

  • Automatic Dependent Surveillance — Dieser Artikel wurde aufgrund von inhaltlichen oder formalen Mängeln auf der Qualitätssicherungsseite des Portals Luftfahrt eingetragen. Dies geschieht, um die Qualität der Artikel aus dem Themengebiet Luftfahrt auf ein akzeptables Niveau zu… …   Deutsch Wikipedia

  • Secondary Surveillance Radar — Sekundärradar der Deutschen Flugsicherung (DFS) mit LVA Antenne (bei Neubrandenburg/ Mecklenburg Vorpommern) …   Deutsch Wikipedia

  • Secondary surveillance radar — SSR antenna of Deutsche Flugsicherung at Neubrandenburg, in Mecklenburg/Western Pomerania Secondary surveillance radar (SSR)[1] is a radar system used in air traffic control (ATC), that not only detects an …   Wikipedia

  • ADS-B — Automatic dependent surveillance broadcast L Automatic dependent surveillance broadcast (ADS B) est un système de surveillance coopératif pour le contrôle du trafic aérien et d autres applications connexes. Un avion équipé de l ADS B détermine sa …   Wikipédia en Français

  • ADSB — Automatic dependent surveillance broadcast L Automatic dependent surveillance broadcast (ADS B) est un système de surveillance coopératif pour le contrôle du trafic aérien et d autres applications connexes. Un avion équipé de l ADS B détermine sa …   Wikipédia en Français

  • ADS-B — Automatic Dependent Surveillance Broadcast Contributor: CASI …   NASA Acronyms

  • DO-242A — Minimum Aviation System Performance Standards for Automatic Dependent Surveillance Broadcast (ADS B) Latest Revision June 25, 2002 Prepared by RTCA SC 186 DO 242A is an aviation system standard published by RTCA, Incorporated. It contains minimum …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.