Exposure (photography)

Exposure (photography)
A long exposure showing stars rotating around the southern and northern celestial poles. Credit: European Southern Observatory
A photograph of the sea after sunset with an exposure time of 15 seconds. The swell from the waves appears as fog.

In photography, exposure is the total density of light allowed to fall on the photographic medium (photographic film or image sensor) during the process of taking a photograph. Exposure is measured in lux seconds, and can be computed from exposure value (EV) and scene luminance over a specified area.

In photographic jargon, an exposure generally refers to a single shutter cycle. For example: a long exposure refers to a single, protracted shutter cycle to capture enough low-intensity light, whereas a multiple exposure involves a series of relatively brief shutter cycles; effectively layering a series of photographs in one image. For the same film speed, the accumulated photometric exposure (Hv) should be similar in both cases.

Contents

Photometric and radiometric exposure

Photometric or luminous exposure[1] Hv is the accumulated physical quantity of visible light energy (weighted by the luminosity function) applied to a surface during a given exposure time. It is defined as:[2]

H_\mathrm{v} = E_\mathrm{v} \cdot t

where

  • Hv is the luminous exposure (usually in lux seconds)
  • Ev is the image-plane illuminance (usually in lux)
  • t is the exposure time (in seconds)

The radiometric quantity radiant exposure[3] He is sometimes used instead; it is the product of image-plane irradiance Ee and time, the accumulated amount of incident "light" energy per area:[4]

H_\mathrm{e} = E_\mathrm{e} \cdot t

where

If the measurement is adjusted to account only for light that reacts with the photo-sensitive surface, that is, weighted by the appropriate spectral sensitivity, the exposure is still measured in radiometric units (joules per square meter), rather than photometric units (weighted by the nominal sensitivity of the human eye).[5] Only in this appropriately weighted case does the H measure the effective amount of light falling on the film, such that the characteristic curve will be correct independent of the spectrum of the light.

Many photographic materials are also sensitive to "invisible" light, which can be a nuisance (see UV filter and IR filter), or a benefit (see infrared photography and full-spectrum photography). The use of radiometric units is appropriate to characterize such sensitivity to invisible light.

In sensitometric data, such as characteristic curves, the log exposure[2] is conventionally expressed as log10(H). Photographers more familiar with base-2 logarithmic scales (such as exposure values) can convert using log2(H) ≈ 3.32 log10(H).

Table 1. SI photometry unitsv · d · e
Quantity Symbol[nb 1] SI unit Symbol Dimension Notes
Luminous energy Qv [nb 2] lumen second lm⋅s T⋅J units are sometimes called talbots
Luminous flux Φv [nb 2] lumen (= cd⋅sr) lm J also called luminous power
Luminous intensity Iv candela (= lm/sr) cd [nb 3] an SI base unit, luminous flux per unit solid angle
Luminance Lv candela per square metre cd/m2 L−2⋅J units are sometimes called nits
Illuminance Ev lux (= lm/m2) lx L−2⋅J used for light incident on a surface
Luminous emittance Mv lux (= lm/m2) lx L−2⋅J used for light emitted from a surface
Luminous exposure Hv lux second lx⋅s L−2⋅T⋅J
Luminous energy density ωv lumen second per metre3 lm⋅sm−3 L−3⋅T⋅J
Luminous efficacy η [nb 2] lumen per watt lm/W M−1⋅L−2⋅T3⋅J ratio of luminous flux to radiant flux
Luminous efficiency V 1 also called luminous coefficient
See also: SI · Photometry · Radiometry · (Compare)

Table 2. SI radiometry unitsv · d · e
Quantity Symbol[nb 4] SI unit Symbol Dimension Notes
Radiant energy Qe[nb 5] joule J M⋅L2⋅T−2 energy
Radiant flux Φe[nb 5] watt W M⋅L2⋅T−3 radiant energy per unit time, also called radiant power.
Spectral power Φ[nb 5][nb 6] watt per metre W⋅m−1 M⋅L⋅T−3 radiant power per wavelength.
Radiant intensity Ie watt per steradian W⋅sr−1 M⋅L2⋅T−3 power per unit solid angle.
Spectral intensity I[nb 6] watt per steradian per metre W⋅sr−1⋅m−1 M⋅L⋅T−3 radiant intensity per wavelength.
Radiance Le watt per steradian per square metre W⋅sr−1m−2 M⋅T−3 power per unit solid angle per unit projected source area.

confusingly called "intensity" in some other fields of study.

Spectral radiance L[nb 6]
or
L[nb 7]
watt per steradian per metre3
or

watt per steradian per square
metre per hertz

W⋅sr−1m−3
or
W⋅sr−1⋅m−2Hz−1
M⋅L−1⋅T−3
or
M⋅T−2
commonly measured in W⋅sr−1⋅m−2⋅nm−1 with surface area and either wavelength or frequency.


Irradiance Ee[nb 5] watt per square metre W⋅m−2 M⋅T−3 power incident on a surface, also called radiant flux density.

sometimes confusingly called "intensity" as well.

Spectral irradiance E[nb 6]
or
E[nb 7]
watt per metre3
or
watt per square metre per hertz
W⋅m−3
or
W⋅m−2⋅Hz−1
M⋅L−1⋅T−3
or
M⋅T−2
commonly measured in W⋅m−2nm−1
or 10−22W⋅m−2⋅Hz−1, known as solar flux unit.[nb 8]


Radiant exitance /
Radiant emittance
Me[nb 5] watt per square metre W⋅m−2 M⋅T−3 power emitted from a surface.
Spectral radiant exitance /
Spectral radiant emittance
M[nb 6]
or
M[nb 7]
watt per metre3
or

watt per square
metre per hertz

W⋅m−3
or
W⋅m−2⋅Hz−1
M⋅L−1⋅T−3
or
M⋅T−2
power emitted from a surface per wavelength or frequency.


Radiosity Je or J[nb 6] watt per square metre W⋅m−2 M⋅T−3 emitted plus reflected power leaving a surface.
Radiant exposure He joule per square metre J⋅m−2 M⋅T−2
Radiant energy density ωe joule per metre3 J⋅m−3 M⋅L−1⋅T−2
See also: SI · Radiometry · Photometry · (Compare)

Optimum exposure

"Correct" exposure may be defined as an exposure that achieves the effect the photographer intended.[6]

A more technical approach recognises that a photographic film (or sensor) has a physically limited useful exposure range,[7] sometimes called its dynamic range.[8] If, for any part of the photograph, the actual exposure is outside this range, the film cannot record it accurately. In a very simple model, for example, out-of-range values would be recorded as "black" (underexposed) or "white" (overexposed) rather than the precisely graduated shades of colour and tone required to describe "detail". Therefore, the purpose of exposure adjustment (and/or lighting adjustment) is to control the physical amount of light from the subject that is allowed to fall on the film, so that 'significant' areas of shadow and highlight detail do not exceed the film's useful exposure range. This ensures that no 'significant' information is lost during capture.

It is worth noting that the photographer may carefully overexpose or underexpose the photograph to eliminate 'insignificant' or 'unwanted' detail; to make, for example, a white altar cloth appear immaculately clean, or to emulate the heavy, pitiless shadows of film noir. However, it is technically much easier to discard recorded information during post processing than to try to 're-create' unrecorded information.

In a scene with strong or harsh lighting, the ratio between highlight and shadow luminance values may well be larger than the ratio between the film's maximum and minimum useful exposure values. In this case, adjusting the camera's exposure settings (which only applies changes to the whole image, not selectively to parts of the image) only allows the photographer to choose between underexposed shadows or overexposed highlights; it cannot bring both into the useful exposure range at the same time. Methods for dealing with this situation include: using some kind of fill lighting to gently increase the illumination in shadow areas; using a graduated ND filter or gobo to reduce the amount of light coming from the highlight areas; or varying the exposure between multiple, otherwise identical, photographs (exposure bracketing) and then combining them afterwards in some kind of HDRI process.

Overexposure and underexposure

White chair: Deliberate use of overexposure for aesthetic purposes.

A photograph may be described as overexposed when it has a loss of highlight detail, that is, when important bright parts of an image are "washed out" or effectively all white, known as "blown out highlights" or "clipped whites".[9] A photograph may be described as underexposed when it has a loss of shadow detail, that is, when important dark areas are "muddy" or indistinguishable from black,[10] known as "blocked up shadows" (or sometimes "crushed shadows," "crushed blacks," or "clipped blacks," especially in video).[11][12][13] As the image to the right shows, these terms are technical ones rather than artistic judgments; an overexposed or underexposed image may be "correct", in that it provides the effect that the photographer intended. Intentionally over- or under- exposing (relative to a standard or the camera's automatic exposure) is casually referred to as "shooting to the right" or "shooting to the left", respectively, as these shift the histogram of the image to the right or left.

Exposure settings

Manual exposure

A longer exposure
A shorter exposure

In manual mode, the photographer adjusts the lens aperture and/or shutter speed to achieve the desired exposure. Many photographers choose to control aperture and shutter independently because opening up the aperture increases exposure, but also decreases the depth of field, and a slower shutter increases exposure but also increases the opportunity for motion blur.

'Manual' exposure calculations may be based on some method of light metering with a working knowledge of exposure values, the APEX system and/or the Zone System.

Automatic exposure

A camera in automatic exposure (abbreviation: AE) mode automatically calculates and adjusts exposure settings to match (as closely as possible) the subject's mid-tone to the mid-tone of the photograph. For most cameras this means using an on-board TTL exposure meter.

Aperture priority mode (commonly abbreviated to Av) gives the photographer manual control of the aperture, whilst the camera automatically adjusts the shutter speed to achieve the exposure specified by the TTL meter. Shutter priority mode (commonly abbreviated to Tv) gives manual shutter control, with automatic aperture compensation. In each case, the actual exposure level is still determined by the camera's exposure meter.

Exposure compensation

The purpose of an exposure meter is to estimate the subject's mid-tone luminance and indicate the camera exposure settings required to record this as a mid-tone. In order to do this it has to make a number of assumptions which, under certain circumstances, will be wrong. If the exposure setting indicated by an exposure meter is taken as the "reference" exposure, the photographer may wish to deliberately overexpose or underexpose in order to compensate for known or anticipated metering inaccuracies.

Cameras with any kind of internal exposure meter usually feature an exposure compensation setting which is intended to allow the photographer to simply offset the exposure level from the internal meter's estimate of appropriate exposure. Frequently calibrated in stops,[14] also known as EV units,[15] a "+1" exposure compensation setting indicates one stop more (twice as much) exposure and "–1" means one stop less (half as much) exposure.[16][17]

Exposure compensation is particularly useful in combination with auto-exposure mode, as it allows the photographer to bias the exposure level without resorting to full manual exposure and losing the flexibility of auto exposure. On low-end video camcorders, exposure compensation may be the only manual exposure control available.

Exposure control

A 1/30s exposure showing motion blur on fountain at Royal Botanic Gardens, Kew
A 1/320s exposure showing individual drops on fountain at Royal Botanic Gardens, Kew

An appropriate exposure for a photograph is determined by the sensitivity of the medium used. For photographic film, sensitivity is referred to as film speed and is measured on a scale published by the International Organization for Standardization (ISO). Faster film, that is, film with a higher ISO rating, requires less exposure to make a good image. Digital cameras usually have variable ISO settings that provide additional flexibility. Exposure is a combination of the length of time and the illuminance at the photosensitive material. Exposure time is controlled in a camera by shutter speed and the illuminance by the lens aperture and the scene luminance. Slower shutter speeds (exposing the medium for a longer period of time), and greater lens apertures (admitting more light), and higher-luminance scenes produce greater exposures.

An approximately correct exposure will be obtained on a sunny day using ISO 100 film, an aperture of f/16 and a shutter speed of 1/100 of a second. This is called the sunny 16 rule: at an aperture of f/16 on a sunny day, a suitable shutter speed will be one over the film speed (or closest equivalent).

A scene can be exposed in many ways, depending on the desired effect a photographer wishes to convey.

Reciprocity

An important principle of exposure is reciprocity. If one exposes the film or sensor for a longer period, a reciprocally smaller aperture is required to reduce the amount of light hitting the film to obtain the same exposure. For example, the photographer may prefer to make his sunny-16 shot at an aperture of f/5.6 (to obtain a shallow depth of field). As f/5.6 is 3 stops "faster" than f/16, with each stop meaning double the amount of light, a new shutter speed of (1/125)/(2·2·2) = 1/1000 is needed. Once the photographer has determined the exposure, aperture stops can be traded for halvings or doublings of speed, within limits.

A demonstration of the effect of exposure in night photography. Longer shutter speeds result in increased exposure.

The true characteristic of most photographic emulsions is not actually linear, (see sensitometry) but it is close enough over the exposure range of about one second to 1/1000 of a second. Outside of this range, it becomes necessary to increase the exposure from the calculated value to account for this characteristic of the emulsion. This characteristic is known as reciprocity failure. The film manufacturer's data sheets should be consulted to arrive at the correction required as different emulsions have different characteristics.

Digital camera image sensors can also be subject to a form of reciprocity failure.[18]

Determining exposure

A fair ride taken with a 2/5 second exposure.

The Zone System is another method of determining exposure and development combinations to achieve a greater tonality range over conventional methods by varying the contrast of the 'film' to fit the print contrast capability. Digital cameras can achieve similar results (high dynamic range) by combining several different exposures (varying only the shutter speeds) made in quick succession.

Today, most cameras automatically determine the correct exposure at the time of taking a photograph by using a built-in light meter, or multiple point meters interpreted by a built-in computer, see metering mode.

Negative/Print film tends to bias for exposing for the shadow areas (film dislikes being starved of light), with digital favouring exposure for highlights. See latitude below.

Latitude

Latitude is the degree by which one can over, or under expose an image, and still recover an acceptable level of quality from an exposure. Typically negative film has a better ability to record a range of brightness than slide/transparency film or digital. Digital should be considered to be the reverse of print film, with a good latitude in the shadow range, and a narrow one in the highlight area; in contrast to film's large highlight latitude, and narrow shadow latitude. Slide/Transparency film has a narrow latitude in both highlight and shadow areas, requiring greater exposure accuracy.

Negative film's latitude increases somewhat with high ISO material, in contrast digital tends to narrow on latitude with high ISO settings.

Highlights

Example image exhibiting blown-out highlights. Top: original image, bottom: blown-out areas marked red

Areas of a photo where information is lost due to extreme brightness are described as having "blown-out highlights" or "flared highlights".

In digital images this information loss is often irreversible, though small problems can be made less noticeable using photo manipulation software. Recording to RAW format can ameliorate this problem to some degree, as can using a digital camera with a better sensor.

Film can often have areas of extreme overexposure but still record detail in those areas. This information is usually somewhat recoverable when printing or transferring to digital.

A loss of highlights in a photograph is usually undesirable, but in some cases can be considered to "enhance" appeal. Examples include black-and-white photography and portraits with an out-of-focus background.

Blacks

Areas of a photo where information is lost due to extreme darkness are described as "crushed blacks". Digital capture tends to be more tolerant of underexposure, allowing better recovery of shadow detail, than same-ISO negative print film.

Crushed blacks cause loss of detail, but can be used for artistic effect.

See also

Notes

  1. ^ Standards organizations recommend that photometric quantities be denoted with a suffix "v" (for "visual") to avoid confusion with radiometric or photon quantities.
  2. ^ a b c Alternative symbols sometimes seen: W for luminous energy, P or F for luminous flux, and ρ or K for luminous efficacy.
  3. ^ "J" is the recommended symbol for the dimension of luminous intensity in the International System of Units.
  4. ^ Standards organizations recommend that radiometric quantities should be denoted with a suffix "e" (for "energetic") to avoid confusion with photometric or photon quantities.
  5. ^ a b c d e Alternative symbols sometimes seen: W or E for radiant energy, P or F for radiant flux, I for irradiance, W for radiant emittance.
  6. ^ a b c d e f Spectral quantities given per unit wavelength are denoted with suffix "λ" (Greek) to indicate a spectral concentration. Spectral functions of wavelength are indicated by "(λ)" in parentheses instead, for example in spectral transmittance, reflectance and responsivity.
  7. ^ a b c Spectral quantities given per unit frequency are denoted with suffix "ν" (Greek)—not to be confused with the suffix "v" (for "visual") indicating a photometric quantity.
  8. ^ NOAA / Space Weather Prediction Center includes a definition of the solar flux unit (SFU).

References

  1. ^ National Institute of Standards and Technology [1]. Retrieved Feb 2009.
  2. ^ a b Geoffrey G. Attridge (2000). "Sensitometry". In Ralph E. Jacobson, Sidney F. Ray, Geoffrey G. Attridge, and Norman R. Axford. The Manual of Photography: Photographic and Digital Imaging (9th ed.). Oxford: Focal Press. pp. 218–223. ISBN 0-240-51574-9. http://books.google.com/books?id=MblHnLN2N2kC&pg=PA218&dq=intitle:manual+sensitometry+exposure+illuminance+time+lux. 
  3. ^ Hsien-Che Lee (2005). Introduction to Color Imaging Science. Cambridge University Press. p. 57. ISBN 9780521843881. http://books.google.com/books?id=CzAbJrLin_AC&pg=PA57&dq=luminous-exposure+radiant-exposure+photography. 
  4. ^ Hans I. Bjelkhagen (1995). Silver-halide Recording Materials. Springer. p. 15. ISBN 9783540586197. http://books.google.com/books?id=tiGP9MrVs90C&pg=PA15&dq=exposure+radiometric+photography. 
  5. ^ Gareth Rees (2001). Physical Principles of Remote Sensing. Cambridge University Press. p. 114. ISBN 9780521669481. http://books.google.com/books?id=u17Zv45DENoC&pg=PA114&dq=film+photometric+radiometric+spectral-sensitivity+exposure. 
  6. ^ Peterson, Bryan, "Understanding Exposure", 2004, ISBN 0-8174-6300-3 : p.14
  7. ^ Ray, S.F. et al. 2000 "The Manual of Photography" Focal Press, ISBN 0-240-51574-9, p.230
  8. ^ Ray, S.F. et al. 2000 "The Manual of Photography" Focal Press, ISBN 0-240-51574-9, p.121 and p.245
  9. ^ Ed van der walt. "Basic Photography - ISO and Film Speed". http://www.illustratedphotography.com/basic-photography/iso-and-film-speed. Retrieved 2 July 2011. 
  10. ^ Rob Sheppard (2010). Digital Photography: Top 100 Simplified Tips & Tricks (4th ed.). John Wiley and Sons. p. 40. ISBN 9780470597101. http://books.google.com/books?id=3M0CZb4dFSgC&pg=PA40. 
  11. ^ Barbara A. Lynch-Johnt and Michelle Perkins (2008). Illustrated Dictionary of Photography. Amherst Media. p. 15. ISBN 9781584282228. http://books.google.com/books?id=ERoH4jlrU5IC&pg=PA15&dq=blocked-up+shadows+crushed. 
  12. ^ Steve Hullfish and Jaime Fowler (2005). Color Correction for Digital Video. Focal Press. pp. 135–136. ISBN 9781578202010. http://books.google.com/books?id=s3rQjdG2pBUC&pg=PA135&dq=crushed+shadows+blocked-up+blacks#PPA135,M1. 
  13. ^ John Jackman (2004). Lighting for Digital Video & Television. Focal Press. p. 60. ISBN 9781578202515. http://books.google.com/books?id=u1C4aZmMeTUC&pg=PA60&dq=crushed-blacks+highlights. 
  14. ^ Chris George (2006). Total Digital Photography. Running Press. pp. 54–55. ISBN 9780762428083. http://books.google.com/books?id=Hr5BPp8Pf2EC&pg=PA54&dq=exposure-compensation+++stops#v=onepage&q=exposure-compensation%20%20%20stops&f=false. 
  15. ^ R E Jacobson (2000). The Manual of Photography. Focal Press. p. 318. ISBN 9780240515748. http://books.google.com/books?id=5YnWKdBWEd8C&lpg=PA318&dq=exposure-compensation%20exposure-value&pg=PA318#v=onepage&q=exposure-compensation%20exposure-value&f=false. 
  16. ^ John Child, Mark Galer (2005). Photographic Lighting : Essential Skills. Focal Press. p. 51. ISBN 9780240519647. http://books.google.com/books?id=ML3S7IuKaXUC&lpg=PP1&pg=PA51#v=onepage&q=exposure%20compensation&f=false. 
  17. ^ David D. Busch (2007). Nikon D80 Digital Field Guide. John Wiley and Sons. p. 11. ISBN 9780470120514. http://books.google.com/books?id=ejLbFj1PvzoC&pg=PA11&dq=exposure-compensation+twice+half#v=onepage&q=exposure-compensation%20twice%20half&f=false. 
  18. ^ David D. Busch (2003). Mastering Digital Photography: The Photographer's Guide to Professional-Quality Digital Photography. Thomson Course Technology. ISBN 1592001149. http://books.google.com/books?visbn=1592001149&id=axTBnNFD6y0C&pg=PA309&lpg=PA309&dq=digital-camera+sensor+%22reciprocity+failure%22#PPA78,M1. 

Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Long exposure photography — is a technique that requires a slow shutter speed to capture light and movement.TechniqueWhen an image is taken including stationary and moving subjects (for example, a fixed street and moving cars or a camera within a car showing a fixed dash… …   Wikipedia

  • Exposure — can refer toIn biology: * A condition of very poor health or death resulting from lack of protection over prolonged periods under weather, extreme temperatures or dangerous substances ( see also: hypothermia, hyperthermia, radioactive… …   Wikipedia

  • Photography — is the art, science and practice of creating durable images by recording light or other electromagnetic radiation, either electronically by means of an image sensor or chemically by means of a light sensitive material such as photographic… …   Wikipedia

  • Exposure compensation — is a technique for adjusting the exposure indicated by a photographic exposure meter, in consideration of factors that may cause the indicated exposure to result in aless than optimal image. Factors considered may include unusual lighting… …   Wikipedia

  • Exposure latitude — is the extent to which a light sensitive material can be over or underexposed and still achieve an acceptable result. Since the acceptability of the result is dependent on both personal aesthetics and artistic intentions, the measurement of… …   Wikipedia

  • photography, technology of — Introduction       equipment, techniques, and processes used in the production of photographs.  The most widely used photographic process is the black and white negative–positive system (Figure 1 >). In the camera the lens projects an image of… …   Universalium

  • photography, history of — Introduction       method of recording the image of an object through the action of light, or related radiation, on a light sensitive material. The word, derived from the Greek photos (“light”) and graphein (“to draw”), was first used in the… …   Universalium

  • Photography and the law — A No Photography sign, commonly placed in properties where the owner objects to or it is illegal to take photographs (though in some jurisdictions, this is not a legal requirement). Photography tends to be protected by the law through copyright… …   Wikipedia

  • Exposure value — In photography, exposure value (EV) denotes all combinations of camera shutter speed and relative aperture that give the same exposure. The concept was developed in Germany in the 1950s (Ray 2000),in an attempt to simplify choosing among… …   Wikipedia

  • photography — I (New American Roget s College Thesaurus) Picture taking Nouns 1. photography, picture taking; aerial, architectural, available light, candid, digital, fashion, fine art, infrared, laser, paper negative, print, product, scenic, still, stereo… …   English dictionary for students

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”