- Four-stroke engine
A four-stroke engine, also known as four-cycle, is an internal combustion engine in which the piston completes four separate strokes—intake, compression, power, and exhaust—during two separate revolutions of the engine's crankshaft, and one single thermodynamic cycle.
There are two common types of engines, which are closely related to each other but have major differences in their design and behavior. The earliest of these to be developed is the Otto cycle engine which was developed in 1876 by Nikolaus August Otto in Cologne, Germany, after the operation principle described by Alphonse_Beau_de_Rochas in 1861. This engine is most often referred to as a petrol engine or gasoline engine, after the fuel that powers it. The second type of four-cycle engine is the Diesel engine developed in 1893 by Rudolph Diesel, also of Germany. Diesel created his engine to maximize efficiency which was lacking in the Otto engine. There are several major differences between the Otto cycle engine and the four cycle diesel engine. The diesel engine is made in both a two-cycle and a four-cycle version. Ironically Otto's company Deutz AG produces primarily diesel engines in the modern era.
The Otto cycle is named after the 1876 engine of Nikolaus A. Otto, who built a successful four-cycle engine which was based on the work of Jean Joseph Etienne Lenoir. It was the third engine type that Otto developed. It used a sliding flame gateway for ignition of its fuel which was a mixture of illuminating gas and air. After 1884 Otto also developed the magneto allowing the use of an electrical spark for ignition, which had been unreliable on the Lenoir engine.
Today, the internal combustion engine (ICE) is used in motorcycles, automobiles, boats, trucks, aircraft, ships, heavy duty machinery, and in its original intended use as stationary power both for kinetic and electrical power generation. Diesel engines are found in virtually all heavy duty applications such as trucks, ships, locomotives, power generation, and stationary power. Many of these diesel engine are two cycle with power ratings up to 105,000 hp (78,000 kW).
The four cycles refer to intake, compression, combustion (power), and exhaust cycles that occur during two crankshaft rotations per power cycle of the four cycle engines. The cycle begins at Top Dead Centre (TDC), when the piston is farthest away from the axis of the crankshaft. A cycle refers to the full travel of the piston from Top Dead Centre (TDC) to Bottom Dead Centre (BDC). (See Dead centre.)
- INTAKE stroke: on the intake or induction stroke of the piston, the piston descends from the top of the cylinder to the bottom of the cylinder, reducing the pressure inside the cylinder. A mixture of fuel and air, or just air in a diesel engine, is forced by atmospheric (or greater) pressure into the cylinder through the intake port. The intake valve(s) then close. The volume of air/fuel mixture that is drawn into the cylinder, relative to the volume of the cylinder is called, the volumetric efficiency of the engine.
- COMPRESSION stroke: with both intake and exhaust valves closed, the piston returns to the top of the cylinder compressing the air, or fuel-air mixture into the combustion chamber of the cylinder head.
- POWER stroke: this is the start of the second revolution of the engine. While the piston is close to Top Dead Center, the compressed air–fuel mixture in a gasoline engine is ignited, usually by a spark plug, or fuel is injected into the diesel engine, which ignites due to the heat generated in the air during the compression stroke. The resulting massive pressure from the combustion of the compressed fuel-air mixture forces the piston back down toward bottom dead centre.
- EXHAUST stroke: during the exhaust stroke, the piston once again returns to top dead center while the exhaust valve is open. This action evacuates the burnt products of combustion from the cylinder by expelling the spent fuel-air mixture out through the exhaust valve(s).
- 1 History
- 2 Thermodynamic Analysis
- 3 Octane Requirements
- 4 Design and engineering principles
- 5 See also
- 6 References
- 7 General sources
- 8 External links
The Otto cycle
Nikolaus August Otto as a young man was a traveling salesman for a grocery concern. In his travels he encountered the internal combustion engine built in Paris by Belgian expatriate Jean Joseph Etienne Lenoir. In 1860 Lenoir succeeded in creating a double acting engine which ran on illuminating gas at 4% efficiency. The 18 liter Lenoir Engine was able to produce only 2 horsepower. The Lenoir engine ran on the illuminating gas that was made from coal which had been developed in Paris by Philip Lebon.
In testing a replica of the Lenoir engine in 1861 Otto became aware of the effects of compression on the fuel charge. In 1862 Otto attempted to produce an engine to improve on the poor efficiency and reliability of the Lenoir engine. He tried to create an engine which would compress the fuel mixture prior to ignition, but failed as that engine would run no more than a few minutes prior to its destruction. Many engineers were also trying to solve the problem with no success.
In 1864 Otto and Eugen Langen founded the first internal combustion engine production company NA Otto and Cie (NA Otto and Company). Otto and Cie succeeded in creating a successful atmospheric engine that same year.
The factory ran out of space and was moved to the town of Deutz, Germany in 1869 where the company was renamed to Deutz Gasmotorenfabrik AG (The Deutz Gas Engine Manufacturing Company). In 1872 Gottlieb Daimler was technical director and Wilhelm Maybach was the head of engine design. Daimler was a gunsmith who had also worked on the Lenoir engine previously.
By 1876 Otto and Langen succeeded in creating the first internal combustion engine that compressed the fuel mixture prior to combustion for far higher efficiency than any engine created to this time.
Gottlieb Daimler and Wilhelm Maybach left their employ at Otto and Cie and developed the first high speed Otto engine in 1883. In 1885 they produced the first automobile to be equipped with an Otto engine. The Petroleum Reitwagen used a hot tube ignition system and the fuel known as Ligroin to become the worlds first internal combustion engine power vehicle using a four cycle engine based on Nikolaus Otto's design. The following year Karl Benz produced a four cycle engined automobile which is called the world's first car by some.
In 1884 Otto's company, now known as Gasmotorenfabrik Deutz (GFD) developed electric ignition and the carburetor.
In 1890 Daimler and Maybach formed a company known as Daimler Motoren Gesellschaft. Today that company is known as Daimler-Benz.
See Otto engine for more detail.
The Diesel cycle
The Diesel Engine (see this page) is a technical refinement of the 1876 Otto Cycle engine. Where Otto had realized in 1861 that the efficiency of the engine could be increased by first compressing the fuel mixture prior to its ignition, Rudolph Diesel wanted to develop a more efficient type of engine that could run on much heavier fuel. The Lenoir, Otto Atmospheric, and Otto Compression engines (both 1861 and 1876) were designed to run on Illuminating Gas (coal gas). With the same motivation as Otto, Diesel wanted to create an engine that would give small industrial concerns their own power source to enable them to compete against larger companies, and like Otto to get away from the requirement to be tied to a municipal fuel supply. Like Otto, it took more than a decade to produce the high compression engine which would self ignite its fuel when that fuel sprayed into the cylinder. Diesel used an air spray combined with fuel in his first engine.
During initial development, one of the engines burst nearly killing Diesel. He persisted and finally created an engine in 1893. The high compression engine which ignites its fuel by the heat of compression is now called the Diesel engine whether it is a four cycle or two cycle design.
The four-cycle diesel engine has been used in the majority of heavy duty applications for many decades. Chief among the reasons for this is that it uses a heavy fuel which contains more energy, requires less refinement, and is cheaper to make (although in some areas of the world Diesel Fuel costs more than Gasoline). The most efficient Otto Cycle engines run near 30% efficiency. The Volkswagen Jetta TDI 1.9 Liter engine achieves 46%. It uses an advanced design with turbocharging and direct fuel injection. Some BMW Ship Diesels with ceramic insulation have exceeded 60% efficiency.
Both Audi and Peugeot compete in the endurance races of the Le Mans Series with Diesel Engined race cars. These are four cycle, four valve, high revving, turbocharged diesels which dominate largely due to fuel economy and having to make fewer stops.
The thermodynamic analysis of the actual four-stroke or two-stroke cycles is not a simple task. However, the analysis can be simplified significantly if air standard assumptions are utilized. The resulting cycle, which closely resembles the actual operating conditions, is the Otto cycle.
Fuel octane rating
During the compression cycle of a compressed charge internal combustion engine the temperature of the fuel air mixture rises as described by Charles Law solely due to the compression of the gases. The temperature rise is several hundreds of degrees.
The fuel used in four cycle engines are most typically fractions of crude oil, coal tar, oil shale, or sands which are produced in a process called Petroleum Cracking. The ignition temperature of the fuel that is refracted is related to its weight. It is separated by being heating and is extracted at different heights in the refractory tower. The higher the fuel vapor rises in the tower the lower its weight and the less energy it contains. In refracting petroleum, there is a standard weight of fuels and products that is withdraw and which is associated with a specific extracted material. Gasoline is a light refractory product and is called a light fraction. As a light fraction it has a relatively low flash point (that is the temperature at which it starts to burn when mixed with an oxidizer).
A fuel with a low flash point may self ignite during compression, and can also be ignited by carbon deposits left in the cylinder or head of a dirty engine. In an internal combustion engine self ignition can occur at unexpected times. During the normal operation of the engine as the fuel mixture is being compressed an electric arc is created to ignite the fuel. At low rpm this occurs close to TDC (Top Dead Center). As engine rpm rises the spark point is moved forward so that the fuel charge can be ignited at a more efficient point in fuel charge compression to allow the fuel to start burning even while it is still being compressed. This produces more effective power based on the rising molecular density of the working medium, since this is the essence of efficiency in the compressed charge IE engine. A more dense working medium (the air fuel mixture) will experience a greater heat, and therefore pressure, rise on less few when its molecules are more densely packed together.
We can see this in two of the designs of the Otto engines. The non-compression engine operated at a 12% efficiency. The compressed charge engine had an operating efficiency of 30%. A Diesel engine can reach as high as 70% (Diesel's lab engine tested at 75.6% efficiency, VW TDI is at 46%).
The problem with compressed charge engines is that the temperature rise of the compressed charge can cause pre-ignition. If this occurs at the wrong time and is too energetic, it can destroy the engine. Fractions of petroleum have widely varying flash points (the temperature at which the fuel may self ignite). This must be taken into account in engine and fuel design.
In engines, the spark is retarded when the engine is being started, and progresses only to an appropriate amount based on engine rpm. This is determined by laboratory research. As the engine revolves faster it can accept earlier ignition since the moving flame front will not have time to be destructive.
In fuel, the tendency for the compressed fuel mixture to ignite early is limited by the chemical composition of the fuel. There are several grades of fuel to accommodate differing performance levels of engines. The fuel is altered to change its self ignition temperature. There are several ways to do this. As engines are designed with higher compression ratios the result is that pre-ignition is much more likely to occur since the fuel mixture will be compressed to a higher temperature prior to deliberate ignition. The higher temperature will more effectively evaporate fuels such as gasoline and is factor in a higher compression engine being higher efficiency. Higher Compression ratios also mean that the distance that the piston can push to produce power is greater (which is called the Expansion ratio).
So there must be a standardized test and a standard reference system to describe how likely a fuel is to self ignite. The octane rating is a measure of the fuel's resistance to self-ignition. A fuel with a higher numerical octane rating allows for a much higher compression ratio, which extracts more energy from the fuel and more effectively converts that energy into useful work while at the same time preventing engine damage from pre-ignition. High Octane fuel is also more expensive.
Diesel engines by their nature do not have concerns with pre-ignition. They have a concern with whether or not combustion can be started. The description of how likely Diesel fuel is to ignite is called the Cetane rating. Because Diesel fuels are of low volatility, they can be very hard to start when cold. Various techniques are used to start a cold Diesel engine, the most common being the use of a glow plug.
In some applications, such as in burning used cooking oil, the fuel itself is solid and must be heated to liquify prior to use. A common complaint here is that the exhaust may have the odor of French Fries.
Design and engineering principles
Power output limitations
The maximum amount of power generated by an engine is determined by the maximum amount of air ingested. The amount of power generated by a piston engine is related to its size (cylinder volume), whether it is a two-stroke or four-stroke design, volumetric efficiency, losses, air-to-fuel ratio, the calorific value of the fuel, oxygen content of the air and speed (RPM). The speed is ultimately limited by material strength and lubrication. Valves, pistons and connecting rods suffer severe acceleration forces. At high engine speed, physical breakage and piston ring flutter can occur, resulting in power loss or even engine destruction. Piston ring flutter occurs when the rings oscillate vertically within the piston grooves they reside in. Ring flutter compromises the seal between the ring and the cylinder wall which results in a loss of cylinder pressure and power. If an engine spins too quickly, valve springs cannot act quickly enough to close the valves. This is commonly referred to as 'valve float', and it can result in piston to valve contact, severely damaging the engine. At high speeds the lubrication of piston cylinder wall interface tends to break down. This limits the piston speed for industrial engines to about 10 m/s.
Intake/exhaust port flow
The output power of an engine is dependent on the ability of intake (air–fuel mixture) and exhaust matter to move quickly through valve ports, typically located in the cylinder head. To increase an engine's output power, irregularities in the intake and exhaust paths, such as casting flaws, can be removed, and, with the aid of an air flow bench, the radii of valve port turns and valve seat configuration can be modified to reduce resistance. This process is called porting, and it can be done by hand or with a CNC machine.
One way to increase engine power is to force more air into the cylinder so that more power can be produced from each power stroke. This can be done using some type of air compression device known as a supercharger, which can be powered by the engine crankshaft.
Supercharging increases the power output limits of an internal combustion engine relative to its displacement. Most commonly, the supercharger is always running, but there have been designs that allow it to be cut out or run at varying speeds (relative to engine speed). Mechanically driven supercharging has the disadvantage that some of the output power is used to drive the supercharger, while power is wasted in the high pressure exhaust, as the air has been compressed twice and then gains more potential volume in the combustion but it is only expanded in one stage.
A turbocharger is a supercharger that is driven by the engine's exhaust gases, by means of a turbine. It consists of a two piece, high-speed turbine assembly with one side that compresses the intake air, and the other side that is powered by the exhaust gas outflow.
When idling, and at low-to-moderate speeds, the turbine produces little power from the small exhaust volume, the turbocharger has little effect and the engine operates nearly in a naturally aspirated manner. When much more power output is required, the engine speed and throttle opening are increased until the exhaust gases are sufficient to 'spin up' the turbocharger's turbine to start compressing much more air than normal into the intake manifold.
Turbocharging allows for more efficient engine operation because it is driven by exhaust pressure that would otherwise be (mostly) wasted, but there is a design limitation known as turbo lag. The increased engine power is not immediately available, due to the need to sharply increase engine RPM, to build up pressure and to spin up the turbo, before the turbo starts to do any useful air compression. The increased intake volume causes increased exhaust and spins the turbo faster, and so forth until steady high power operation is reached. Another difficulty is that the higher exhaust pressure causes the exhaust gas to transfer more of its heat to the mechanical parts of the engine.
Rod and piston-to-stroke ratio
The rod-to-stroke ratio is the ratio of the length of the connecting rod to the length of the piston stroke. A longer rod will reduce the sidewise pressure of the piston on the cylinder wall and the stress forces, hence increasing engine life. It also increases the cost and engine height and weight.
A "square engine" is an engine with a bore diameter equal to its stroke length. An engine where the bore diameter is larger than its stroke length is an oversquare engine, conversely, an engine with a bore diameter that is smaller than its stroke length is an undersquare engine.
The valves are typically operated by a camshaft rotating at half the speed of the crankshaft. It has a series of cams along its length, each designed to open a valve during the appropriate part of an intake or exhaust stroke. A tappet between valve and cam is a contact surface on which the cam slides to open the valve. Many engines use one or more camshafts “above” a row (or each row) of cylinders, as in the illustration, in which each cam directly actuates a valve through a flat tappet. In other engine designs the camshaft is in the crankcase, in which case each cam contacts a push rod, which contacts a rocker arm which opens a valve. The overhead cam design typically allows higher engine speeds because it provides the most direct path between cam and valve.
Valve clearance refers to the small gap between a valve lifter and a valve stem that ensures that the valve completely closes. On engines with mechanical valve adjustment excessive clearance will cause noise from the valve train. Typically the clearance has to be readjusted each 20,000 miles (32,000 km) with a feeler gauge.
Most modern production engines use hydraulic lifters to automatically compensate for valve train component wear. Dirty engine oil may cause lifter failure.
Otto engines are about 30% efficient; in other words, 30% of the energy generated by combustion is converted into useful rotational energy at the output shaft of the engine, while the remainder being losses due to friction, engine accessories, and waste heat. There are a number of ways to recover some of the energy lost to waste heat. The use of a Turbocharger in Diesel engines is very effective by boosting incoming air pressure and in effect provides the same increase in performance as having more displacement. The Mack Truck company decades ago developed a turbine system which converted waste heat into kinetic energy which was fed back into the engine's transmission. More recently BMW developed a two stage heat recovery system similar to the Mack system that recovers 80% of the energy in the exhaust gas and raised the efficiency of the Otto engines it is applied to by 15% putting the Otto engine on par with some Diesel engines.
By contrast, a six-stroke engine may convert more than 50% of the energy of combustion into useful rotational energy.
Modern engines are often intentionally built to be slightly less efficient than they could otherwise be. This is necessary for emission controls such as exhaust gas recirculation and catalytic converters that reduce smog and other atmospheric pollutants. Reductions in efficiency may be counteracted with an engine control unit using lean burn techniques.
In the United States, the Corporate Average Fuel Economy will mandate that vehicles must achieve an average of 35.5 miles per gallon (mpg) compared to the current standard of 25 mpg. As automakers look to meet these standards by 2016, new ways of engineering the traditional internal combustion engine (ICE) could have to be considered. Some potential solutions to increase fuel efficiency to meet new mandates include firing after the piston is farthest from the crankshaft, known as top dead centre, and applying the Miller cycle. Together, this redesign could significantly reduce fuel consumption and NOx emissions.
- ^ a b c d , Nikolaus August Otto: Inventor Of The Internal Combustion Engine.
- ^ Brittanica, Britannica Gasoline Engine.
- ^ a b c d , NA Otto Museum.
- ^ Best Place for Engineering and Technology, Air Standard Assumptions.
- ^ http://www.ecen.com/content/eee7/motoref.htm Otto Engine Efficiency], Efficiencies of Internal Combustion Engines.
- ^ BMW Turo Steamer, BMW Turbo Steamer Gets Hot and Goes.
- ^ Air pollution from motor vehicles By Asif Faiz, Christopher S. Weaver, Michael P. Walsh
- Hardenberg, Horst O. (1999). The Middle Ages of the Internal combustion Engine. Society of Automotive Engineers (SAE). ISBN 9780768003918.
- Cengel, Yunus A; Michael A Boles, Yaling He (2009). Thermodynamics An Engineering Approach. N.p.. The McGraw Hill Companies. ISBN 9787121084782.
- Benson, Tom (11 July 2008). "4 Stroke Internal Combustion Engine". http://www.grc.nasa.gov/WWW/K-12/airplane/engopt.html. Retrieved 5 May 2011.
- U.S. Patent 194,047
- Detailed Engine Animations
- How Car Engines Work
- Animated Engines, four stroke another explanation of the four-stroke engine
- CDX eTextbook – some videos of car components in action
- Video from inside a four-stroke engine cylinder.
Reciprocating engines and configurations Type Stroke cyclesTwo-stroke cycle · Four-stroke cycle · Six-stroke cycle Engine
configurationsI2 · I3 · I4 · I5 · I6 · I7 · I8 · I9 · I10 · I12 · I14F2 · F4 · F6 · F8 · F12 · F16Other inline
ComponentsEvans · Peaucellier–Lipkin · Sector straight-line · Watt's (parallel)Other Aircraft piston engine components, systems and terminology Piston engines
- Mechanical components
Camshaft · Connecting rod · Crankpin · Crankshaft · Cylinder · Cylinder head · Gudgeon pin · Hydraulic tappet · Main bearing · Obturator ring · Oil pump · Piston · Piston ring · Poppet valve · Pushrod · Rocker arm · Sleeve valve · Tappet
- Electrical components
Air-cooled · Bore · Compression ratio · Dead centre · Engine displacement · Four-stroke engine · Horsepower · Ignition timing · Manifold pressure · Mean effective pressure · Naturally-aspirated · Monosoupape · Overhead camshaft · Overhead valve · Rotary engine · Shock-cooling · Stroke · Time between overhaul · Two-stroke engine · Valve timing · Volumetric efficiency
Propellers Engine instruments Engine controls Fuel and induction system Other systems
Wikimedia Foundation. 2010.
Look at other dictionaries:
four-stroke engine — n an engine that works with two up and down movements of a ↑piston … Dictionary of contemporary English
four-stroke engine — keturtaktis variklis statusas T sritis Energetika apibrėžtis Stūmoklinis vidaus degimo variklis, kurio darbo ciklas vyksta per keturias stūmoklio eigas. atitikmenys: angl. four stroke engine vok. Viertaktmotor, m rus. четырехтактный двигатель, m… … Aiškinamasis šiluminės ir branduolinės technikos terminų žodynas
four stroke engine — four cylinder engine, internal combustion engine comprised of four pistons … English contemporary dictionary
four-stroke engine — noun an internal combustion engine in which an explosive mixture is drawn into the cylinder on the first stroke and is compressed and ignited on the second stroke; work is done on the third stroke and the products of combustion are exhausted on… … Useful english dictionary
four-stroke engine — noun An engine in which the pistons perform four strokes per engine cycle (i.e. intake, compression, power, exhaust). See Also: two stroke engine … Wiktionary
four cycle engine — See four stroke cycle engine … Dictionary of automotive terms
four-cycle engine — See four stroke cycle engine … Dictionary of automotive terms
Stroke (engine) — Reciprocating motion, used in reciprocating engines and other mechanisms, is back and forth motion. Each cycle of reciprocation consists of two opposite motions: there is a motion in one direction, and then a motion back in the opposite direction … Wikipedia
four-stroke internal-combustion engine — noun an internal combustion engine in which an explosive mixture is drawn into the cylinder on the first stroke and is compressed and ignited on the second stroke; work is done on the third stroke and the products of combustion are exhausted on… … Useful english dictionary
four-stroke — /ˈfɔ stroʊk/ (say faw strohk) adjective 1. denoting or relating to an internal combustion engine cycle in which one piston stroke out of every four is a power stroke. 2. powered by such an engine. –noun 3. a four stroke engine or vehicle. Compare … Australian English dictionary