Prepress proofing

Main article: Prepress

A Contract Proof^[1] usually serves as an agreement between customer and printer and as a color reference guide for adjusting the press before the final press run.^[2] Most contract proofs are a Prepress Proof.^[3]

The primary goal of 'proofing' is to serve as a tool for customer verification that the entire job is accurate. Prepress proofing (also known as off-press proofing^[4]) is a cost effective way of providing a visual copy without the expense of creating a Press Proof.^[5] If errors are found during the printing process on press it can prove very costly to one or both parties involved.

Press time is the most expensive part of print media. The main objective of proofing is to produce either a soft or hard copy of what the final product will look like on press. Hard copy proofing usually involves ink-jet printing or other technologies (i.e. Laminate Proof^[6]) to produce high-quality one-off copies of the production artwork. Soft proofing usually involves highly color accurate wide-gamut computer displays.

"The printed proof is a dispassionate simulation of the ultimate output - a CMYK press sheet. The mission of a proofing system is to create accurate predictions, not pretty pictures."^[7] In the best conditions the proofing process will actually try to emulate the effects of the printing press through color management and screening techniques, which can be quite challenging because proofing devices may behave and operate quite differently than press devices.

History

Since the first days of Johannes Gutenberg proofing has just been press proofs - you make a short run on press to verify what you are going to do on a production run. As technology evolved to lower the per-copy cost of a printing job, the cost of starting a production run continued to rise. Today it can be very costly to start up a production press, and cost prohibitive to run a press proof. While some people may think a press proof is the ultimate proof quality, this is not necessarily so, especially if the production run is done days or weeks later when press conditions may have changed, or the production run is done on a different press than the press proof.

In the late 1940s the first overlay^[8] systems were developed. These system produce each of the process colors on a separate sheet of clear film and then register them together to view the final proof.

The Ozalid division of General Aniline and Film Corporation created Ozachrome^[9] as the first commercial system used in proofing. Diazo (light sensitive dye) coatings on film were used for each of the process colors and the films were developed using ammonia vapor. Interestingly, the initial process colors used were red, yellow, blue and black, although other colors may have been used in subsequent years. A black separation was processed on a white paper, while the remaining separations were processed on clear cellulose acetate.

Around 1965 3M invented an overlay system called Color Key. Basically sheets of clear polyester were coated with UV sensitive pigmented emulsions in the four process colors, cyan, magenta, yellow and black. Later spot colors were created (Color Key Custom Colors). The sheets were exposed to the artwork via a carbon arc lamp, washed with water and process chemicals, then dried.

As of 2010 overlay proofs are still created, for example for small single drum presses where each color has to be a separate run. Such proofs are usually made using either inkjet printers or lamination devices.

Internal^[10] (single-sheet) or laminate systems attempt to overcome the problems with overlay systems by putting all process colors on a single sheet of media. After the end of World War II the first commercial system, called Watercote, was introduced by the Direct Reproduction Corporation.

By the 1970s 3M developed Transfer Key technology which used a cold lamination adhesive process. Successive layers of colored adhesive would be pressed on the substrate, exposed and washed away until all the colors existed on a single substrate. This later evolved into the Match Print product which used a thermal transfer lamination process. The Match Print trade mark has since been sold to Kodak which uses it today in its MATCHPRINT InkJet and MATCHPRINT Virtual products. Both Color Key^[11] and Match Print^[12] have also become generic names for types of prepress proofs. Later other similar water process products such as DuPont Waterproof came on the market.

In the early 1960's, several attempts were made to develop electrophotographic proofing processes based on the electrofax principle, using paper coated with zinc oxide in a resistive binder as a photoconductor and toners consisting of ink pigments dispersed in liquid Isopar. The electrofax principle was introduced in the United States by RCA. and the use of liquid toners was developed in Australia by Ralph Metcalf and Robert Wright of the Australian government. Other groups worked on similar processes, but never got to market.^[10]

Later in the 1970s toner based solutions such as Dupont Cromalin were developed.

By the 1980s custom colors, including while and metallics such as gold and silver were becoming common place.

By 1987 the first Iris printer was commercialized. This was a continuous stream inkjet printer that was later followed by the Veris printer in 2004. Initially these printers had unparalleled quality in inkjet printing, but steady advances in drop-on-demand printers has made their quality acceptable to more and more prepress shops. As of 2010 both Iris and Veris devices are still in use.

In the early 1990s Dye Sublimation was introduced with products like 3M Rainbow and Kodak DCP9000 and DCP9500.

Also in the early 1990s Laser Sublimation systems were introduced. Products such as the Fuji FINALPROOF, and Kodak Approval are still in use today.

In the late 1990s laser thermal transfer was developed. These systems are still in use such as the Creo (now Kodak) Spectrum. The Spectrum was notable in that the same platesetter device used to make plates was also used to make proofs, resulting in proofs with identical screening as the press.

By 2005 the first spectrophotometers were integrated with inkjet printers, such as the Creo Veris and HP 2100. By 2009 Epson released a printer with an integrated spectrophotometer. This eliminates much of the labor involved in calibrating the proofing system and validating the proofs by automating the measurement process. However, it slows down overall throughput of the proofing device, so more proofing devices are needed to maintain throughput.

By 2003 soft proofing emerged using well calibrated and profiled computer displays under highly controlled viewing conditions. This approach continues to gain in popularity due to the much lower cost and lesser production time than producing a hard copy proof.

As of 2010 the majority of hard copy contract proofing is done on inkjet and laminate devices, and soft proofing continues to gain in popularity.

Since the late 1990s a number of software proofing solutions developed where the vendors relied upon 3rd party output devices such as Canon, Epson, HP, etc. inkjet printers. Companies include EFI, GMG, Creo (now Kodak), CGS, Serendipity Software, etc. Previously proofing systems were typically a complete solution from one vendor, but as software has become the dominate enabling technology in proofing, customers enjoy the benefits of being able to use commodity print devices over special proofing devices.

Proofing methods

Depending on the quality needed and the use of product there are two major types of proof:

• soft proof;
• hard proof;

Soft proof

Soft proof describes the simulation of the print result on a monitor.^[13] This is the cheapest solution for proofing since no additional equipment, except a monitor, is needed.

Usually soft proof is done in software applications in combination with color management systems. The monitor used for soft proofing has to be calibrated, so that the image on the screen looks like the image on the paper. The major problem is the difference of color spaces (RGB in monitor and CMYK in print) and it is solved by using ICC profiles for input and output devices. Moreover, colors on a monitor depend not only on its properties, but also on lighting conditions in a room where the image is viewed. Usually lighting is standardized and is close to a daylight (D50).

Soft proofing can be used unlimited number of times and is most useful when editing images and designing layout, but is normally not used as a contract proof.

Hard proof

Hard proof is an actual printed sample of a printed product. It is further divided into five general classifications ^[13]

Blueprint (originated from conventional platemaking) is a copy printed in one color and used for checking and correcting mistakes in contents, imposition layout and completeness of data.

Imposition proof (Layout proof) is similar to blueprint but the copy is printed in color. Imposition proof is usually done with a large-format color inkjet printer.

Color proof provides the color-reliable/color-true reproduction of the contents of the file intended for printing. Color proof is made with inkjet printers or thermal sublimation printers in combination with powerful color management systems. Proofing is performed in full-size format while in some cases small page format is also acceptable. Color proof serves as a guideline for a printing press operator and usually stands for a contract proof.

Screen Proof (True Proof) is a method of proofing used for simulating a raster structure of the printed image. Performing this proof makes it possible to recognize different raster-dependent effects such as smoothness, grade and range of tonal gradations, and moiré or rosette patterns.

Several vendors offer special proof systems for creating a screen proof. The proof is produced via color donors and thermal transfer (ablation) onto intermediate carriers or onto the substrate used for the print run. Both systems are imagesetter-like devices with which the image motifs can be reproduced in every detail including their color, screen definition, and screen angles. The true proof systems use color foils that are to be processed in separate units (laminators), transferred from intermediate carriers onto production paper and/or laminated, either to protect the proof or to give it the appearance of the surface structure of production paper.^[13]

Press proof is a test print of the data directly in a printing press. This can be the press for the production run or a comparable press (using the same print technology) prepared especially for proof purposes. Short runs of 50 or 100 copies can be produced more cost-effectively than with other color proof processes. The individual proof is, however, hardly economically justifiable.^[13]

Issues

Proofing can either be viewed subjectively as an art based on training, experience, talent and judgment; or objectively as a science based on measurement, algorithms, and analysis; but in practice it is somewhere in between. Increasingly, however, printers rely on scientific methods as it is often more cost effective to buy the necessary technology than to acquire, train and retain skilled artisans.

In many cases it makes sense to align the proof with the press, but in other cases it makes sense to align the press with the proof.^[14] Typically you would align the press with the proof when you are trying to achieve a particular industry specification (i.e. Fogra,^[15] GRACoL,^[16] SWOP,^[17] etc.). In situations where you are trying to achieve the best possible color on a particular press, typically to distinguish yourself as a printer, you would define a custom color standard for the press and align your proof with the press.

Process Control

A central aspect of scientific proofing is process control, which consists of baselining, characterizing and calibrating the proofing process.

A baseline is representation of the output device settings (i.e. paper feed, head alignment, etc.) and associated conditions (i.e. media, ink, screening, etc.). A baseline is created by adjusting device settings under a given set of conditions and running test samples, measuring the samples, readjusting the settings, until the output process is brought to an optimal state. Once optimized, a final set of measurements are made of output samples and this data becomes part of the baseline information.

The baseline is then characterized by outputting ECI^[18] or IT8.7/4^[19] test charts (samples of color patches), then the charts are scanned with a spectrophotometer to finally produce a color profile of the baseline.

Over time specific device performance (and other conditions) may vary. Certainly different devices of the same device type will also vary with respect to the baseline data. However it is essential that the proofing system always perform as closely as possible to the original color profile. Calibration is a process of outputting more color charts, measuring them and adjusting the color mapping until system performance is as close as possible to the original baseline and color profile. During calibration device settings may also be changed to achieve an optimal output process and subsequent color match.

In ideal circumstances the printing press will also be characterized and calibrated using similar techniques. When there exists a color profile of the press device and a color profile of proofing device, the best emulation of the press on the proofing device is possible. Doing this accurately requires well controlled and repeatable processes (including calibration) to ensure that the color profiles continue to represent the devices involved.

Proof Validation is another aspect of process control. While calibration only ensures that the proofing system is producing output as close to the baseline as possible, proof validation embeds color charts in the artwork itself to ensure that at the artwork matches an industry color standard or a custom color standard (i.e. a specific press that has been characterized). In short it validates that the proofing system emulates the desired press results accurately.

Proofing for Packaging

Producing proofs for packaging faces a number of challenges beyond those for conventional offset press.

Often customers want 3 dimensional mock-ups of the actual package. This could be cardboard, metal (i.e. aluminum pop can), glass, plastic, etc. This can be very difficult, or impossible to do effectively using inkjet printers so typically laminate processes such as Kodak APPROVAL or Fuji FINALPROOF are needed so that the proof can be transferred to the preferred packaging materials.

In the case of cardboard cartons an automated cutting & creasing table is useful. Typically Computer Aided Design (CAD) software is used to define the cuts and creases based on the proof geometry and this is fed into the cutting & creasing table software.

Most packaging is printed using Flexography because it is more versatile over the range of materials used in packaging. However the image quality of flexographic prints is often inferior to offset press, and it is important to simulate the characteristics of the press in the proofs so that customers have realistic expectations for the final packaging. Similarly certain materials, such as corrugated cardboard, add their own characteristics to the image, and these too need to be simulated.

References

1. ^ Contract Proof
2. ^ theprintspace (2010), CMYK Proof, theprintspace, retrieved on 10 March 2010
3. ^ Prepress Proof
4. ^ Frank J. Romano, "Pocket Guide to Digital Prepress", © 1996, Delmar Publishers, page 109, ISBN 0-8273-7198-5
5. ^ Press Proof
6. ^ Laminate Proof
7. ^ Rick McCleary, "CMYK 2.0, A Cooperative Workflow for Photographers, Designers, and Printers", © 2009, Peachpit Press, page 70, ISBN 978-0-321-57346-9
8. ^ Overlay Proof
9. ^ Louis Walton Sipley, "A Half Century of Color", The Macmillan Company, © 1951, page 207
10. ^ ^{a b} Frank J. Romano, "Pocket Guide to Digital Prepress", © 1996, Delmar Publishers, page 111, ISBN 0-8273-7198-5
11. ^ Color Key
12. ^ Match Print
13. ^ ^{a b c d} Helmut Kipphan (2001), Handbook of Print Media, Berlin: Heidelberg
14. ^ Press and proof alignment strategies
15. ^ Fogra
16. ^ GRACoL
17. ^ SWOP
18. ^ European Color Initiative
19. ^ ANSI IT8.7/4-2005 Graphic technology - Input data for characterization of 4-color process printing - Expanded data set

See also

• Online artwork proofing, feedback, review and approval tool
• Online proofing
• Press check (printing)