Current sense amplifier

Current sense amplifier

Current sense amplifiers (also called current shunt amplifiers) are special purpose amplifiers that output a voltage proportional to the current flowing in a power rail. They utilize a "current-sense resistor" to convert the load current in the power rail to a small voltage, which is then amplified by the current-sense amplifiers. The currents in the power rail can be in the range of 1 A to 20 A, as a result, the current-sense resistor is a very low ohmic value resistor (usually in the range of a 1 mΩ to 100 mΩ). These amplifiers are designed to amplify a very small "sense voltage"—in the order of 10 mV to 100 mV in the presence of very large common-mode voltages—in the order of 5 V to 30 V). DC precision (low input offset voltage) and high common-mode rejection ratio (CMRR) are distinguishing characteristics of these amplifiers. Current sense amplifiers can either measure current flowing in a single direction or bidirectional amplifiers can measure current flow in both directions through the sense resistor.[1]

Traditional differential amplifiers (same applies to operational amplifiers or op amps) powered between two power supply rails (say VCC and VEE) can only process/amplify signals that lie between these two power rails. If any voltage greater than these power supply rails are applied to their input pins, internal ESD protection diodes turn-on, causing large currents to flow and damage these parts

High-side current-sense amplifiers, by contrast, are amplifiers with a special architecture. Even when powered from a low-voltage power rail such as VCC = 5 V and VEE = 0 V, they can withstand pin voltages much higher than VCC and much lower than VEE. These amplifiers use specialized ESD structures that enable them to have this functionality. In addition, their input stages are designed such that when the input common-mode voltage is much higher than VCC (or conversely, much lower than VEE), the input amplifier stage powers itself from the input common-mode voltage instead of VCC (or VEE).[2]

Examples include LTC6101,MAX4080, AD8210 and INA193. In special cases, no VCC pin is required to accomplish current-sensing—such as MAX9938.

See also

References

  1. ^ Complete Solutions Guide For Current Sense ApplicationsPDF
  2. ^ Difference and Current sense AmplifiersPDF

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Current source — Figure 1: An ideal current source, I, driving a resistor, R, and creating a voltage V A current source is an electrical or electronic device that delivers or absorbs electric current. A current source is the dual of a voltage source. The term… …   Wikipedia

  • Operational amplifier — A Signetics μa741 operational amplifier, one of the most successful op amps. An operational amplifier ( op amp ) is a DC coupled high gain electronic voltage amplifier with a differential input and, usually, a single ended output.[1] An op amp… …   Wikipedia

  • Electronic amplifier — A practical amplifier circuit An electronic amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. In… …   Wikipedia

  • Valve audio amplifier - technical — Circuitry and performance Characteristics of valves Valves are very high input impedance (near infinite in most circuits) and high output impedance devices. They are also high voltage / low current devices.While valves themselves are described… …   Wikipedia

  • Residual-current device — A two pole residual current device A Residual Current Device is a generic term covering both RCCBs and RCBOs. A Residual Current Circuit Breaker (RCCB) is an electrical wiring device that disconnects a circuit whenever it detects that the… …   Wikipedia

  • Idling current — refers to the current trickling through a circuit (or more commonly through transistors) such as an amplifier when the system is on, but doing no useful work. This is also known as quiescent current.Many electrical appliances including computer… …   Wikipedia

  • Signal-flow graph — A signal flow graph (SFG) is a special type of block diagram[1] and directed graph consisting of nodes and branches. Its nodes are the variables of a set of linear algebraic relations. An SFG can only represent multiplications and additions.… …   Wikipedia

  • Dynamic random-access memory — DRAM redirects here. For other uses, see Dram (disambiguation). Computer memory types Volatile RAM DRAM (e.g., DDR SDRAM) SRAM In development T RAM Z RAM TTRAM Historical Delay line memory Selectron tube Williams tube …   Wikipedia

  • Minor loop feedback — is a classical method used to design stable robust linear Feedback control systems using feedback loops around sub systems within the over all feedback loop.[1] The method is sometimes called minor loop synthesis in college text books,[2][3] some …   Wikipedia

  • Dynamic random access memory — (DRAM) is a type of random access memory that stores each bit of data in a separate capacitor within an integrated circuit. Since real capacitors leak charge, the information eventually fades unless the capacitor charge is refreshed periodically …   Wikipedia

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”