Blanking and piercing

Blanking and piercing
Blanking versus piercing

Blanking and piercing are shearing processes in which a punch and die are used to modify webs. The tooling and processes are the same between the two, only the terminology is different: in blanking the punched out piece is used and called a blank; in piercing the punched out piece is scrap.[1]

Contents

Types

There are various types of blanking and piercing: lancing, perforating, notching, nibbling, shaving, cutoff, and dinking.

Lancing

Lancing is a piercing operation in which the workpiece is sheared and bent with one strike of the die. A key part of this process is that there is not reduction of material, only a modification in its geometry. This operation is used to make tabs, vents, and louvers.

The cut made in lancing is not a closed cut, like in perforation even though a similar machine is used, but a side is left connected to be bent sharply or in more of a rounded manner.

Lancing can be used to make partial contours and free up material for other operations further down the production line. Along with these reasons lancing is also used to make tabs (where the material is bent at a 90 degree angle to the material), vents (where the bend is around 45 degrees), and louvers (where the piece is rounded or cupped).

Normally lancing is done on a mechanical press, lancing requires the use of punches and dies to be used. The different punches and dies determine the shape and angle (or curvature) of the newly made section of the material. The dies and punches are needed to be made of tool steel to withstand the repetitious nature of the procedure.[2]

Perforating

Perforating is a piercing operation that involves punching a large number of closely spaced holes.[1]

Notching

Notching is a piercing operation that removes material from the edge of the workpiece.[3]

Nibbling

The nibbling process cuts a contour by producing a series of overlapping slits or notches. This allows for complex shapes to be formed in sheet metal up to 6 mm (0.25 in) thick using simple tools.[3] The nibbler is essentially a small punch and die that reciprocates quickly; around 300–900 times per minute. Punches are available in various shape and sizes; oblong and rectangular punches are common because they minimize waste and allow for greater distances between strokes, as compared to a round punch. Nibbling can occur on the exterior or interior of the material, however interior cuts require a hole to insert the tool.[4]

The process is often used on parts that do not have quantities that can justify a dedicated blanking die. The edge smoothness is determined by the shape of the cutting die and the amount the cuts overlap; naturally the more the cuts overlap the cleaner the edge. For added accuracy and smoothness most shapes created by nibbling undergo filing or grinding processes after completion.[3]

Shaving

The shaving process is a finishing operation where a small amount of metal is sheared away from an already blanked part. Its main purpose is to obtain better dimensional accuracy, but secondary purposes include squaring the edge and smoothing the edge. Blanked parts can be shaved to an accuracy of up to 0.025 mm (0.001 in).[3]

Trimming

The trimming operation is the last operation performed because it cuts away excess or unwanted irregular features from the workpiece.

Cutoff

The cutoff process is used to separate a stamping or other product from a strip or stock. This operation is very common with progressive die sequences. The cutoff operation often produces the periphery counter to the workpiece.[3]

Fine blanking

Typical fine blanking press cross section

Fine blanking is a specialized form of blanking where there is no fracture zone when shearing. This is achieved by compressing the whole part and then an upper and lower punch extract the blank.[5] This allows the process to hold very tight tolerances, and perhaps eliminate secondary operations.

Materials that can be fine blanked include aluminium, brass, copper, and carbon, alloy and stainless steels.

Fine blanking presses are similar to other metal stamping presses, but they have a few critical additional parts. A typical compound fine blanking press includes a hardened die punch (male), the hardened blanking die (female), and a guide plate of similar shape/size to the blanking die. The guide plate is the first applied to the material, impinging the material with a sharp protrusion or stinger around the perimeter of the die opening. Next a counter pressure is applied opposite the punch, and finally the die punch forces the material through the die opening. Since the guide plate holds the material so tightly, and since the counter pressure is applied, the material is cut in a manner more like extrusion than typical punching. Mechanical properties of the cut benefit similarly with a hardened layer at the cut edge from theof the part.[6] Because the material is so tightly held and controlled in this setup, part flatness remains very true, distortion is nearly eliminated, and edge burr is minimal. Clearances between the die and punch are generally around 1% of the cut material thickness, which typically varies between 0.5–13 mm (0.020–0.51 in).[7] Currently parts as thick as 19 mm (0.75 in) can be cut using fine blanking.[8] Tolerances between ±0.0003–0.002 in (0.0076–0.051 mm) are possible based on material thickness & tensile strength, and part layout.[9]

With standard compound fine blanking processes, multiple parts can often be completed in a single operation. Parts can be pierced, partially pierced, offset (up to 75°), embossed, or coined, often in a single operation.[10] Some combinations may require progressive fine blanking operations, in which multiple operations are performed at the same pressing station.

The advantages of fine blanking are:

  • excellent dimensional control, accuracy, and repeatability through a production run.
  • excellent part flatness is retained.
  • straight, superior finished edges to other metal stamping processes.
  • smaller holes possible relative to thickness of material.[11]
  • little need to machine details.
  • multiple features can be added simultaneously in 1 operation.[11]
  • more economical for large production runs than traditional operations when additional machining cost and time are factored in (1000–20000 parts minimum, depending on secondary machining operations)[12]

The disadvantages are:

  • slightly higher tooling cost when compared to traditional punching operations.
  • slightly slower than traditional punching operations.

Tooling

The amount of clearance between a punch and die for piercing is governed by the thickness and strength of the workpiece material being pierced. The punch-die clearance determines the load or pressure experienced at the cutting edge of the tool, commonly known as point pressure. Excessive point pressure can lead to accelerated wear and ultimately failure.

Burr height is typically used as an index to measure tool wear, because it is easy to measure during production.

A simple operation may only need a pancake die. While many dies perform complex procedures simultaneously, a pancake die may only perform one simple procedure with the finished product being removed by hand.

References

  1. ^ a b Degarmo, p. 427.
  2. ^ Todd (1994), Manufacturing Processes Reference Guide, New York: Industrial Press, pp. 84–85, ISBN 0831130490 
  3. ^ a b c d e Degarmo, p. 428.
  4. ^ Todd, pp. 97–98.
  5. ^ Degarmo, p. 425.
  6. ^ "Fineblanking 101". http://www.partechfineblanking.com/fineblanking101.htm. Retrieved 2008-11-05. 
  7. ^ Kalpakjian, Serope; Schmid, Steven R. (2006). Manufacturing Engineering and Technology (5th ed.). Upper Saddle River, NJ: Pearson Prentice Hall. p. 429. ISBN 0-13-148965-8. 
  8. ^ "Fine blanking history". http://www.fineblanking.org/overview/history.html. Retrieved 2008-11-05. 
  9. ^ MPI International, Inc. "Guidelines". http://www.mpi-int.com/guidelines.pdf. Retrieved 2008-11-05. 
  10. ^ Bralla, pp. 3.47–3.48.
  11. ^ a b "Fine blanking benefits". http://www.fineblanking.org/overview/benefits.html. Retrieved 2008-11-05. 
  12. ^ Bralla, pp. 3.49–3.50.

Bibliography


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Piercing (metalworking) — Piercing is a shearing process where a punch and die are used to create a hole in sheet metal or a plate. The process and machinery are usually the same as that used in blanking, except that the piece being punched out is scrap in the piercing… …   Wikipedia

  • Blanking (metalworking) — Blanking is a shearing process where a punch and die are used to create a blank from sheet metal or a plate. The process and machinery are usually the same as that used in piercing, except that the piece being punched out in the piercing process… …   Wikipedia

  • Die (manufacturing) — For the thread cutting tool, see Tap and die. A die is a specialized tool used in manufacturing industries to cut or shape material using a press. Like molds, dies are generally customized to the item they are used to create. Products made with… …   Wikipedia

  • Pancake die — A pancake die is a simple type of manufacturing die that performs blanking and/or piercing. Many dies perform complex procedures simultaneously (or progressively for progressive die) such as coining, piercing, forming, bending in addition to… …   Wikipedia

  • AMX-30 — French AMX 30B2 sporting a 105 rifled tank gun Type Main battle tank Place of origin …   Wikipedia

  • Stamping (metalworking) — Contents 1 Operations 2 Simulation 3 See also 4 References …   Wikipedia

  • Work hardening — Work hardening, also known as strain hardening or cold working, is the strengthening of a metal by plastic deformation. This strengthening occurs because of dislocation movements within the crystal structure of the material.[1] Any material with… …   Wikipedia

  • Shearing (manufacturing) — Shearing, also known as die cutting,[1] is a process which cuts stock without the formation of chips or the use of burning or melting. Strictly speaking, if the cutting blades are straight the process is called shearing; if the cutting blades are …   Wikipedia

  • Shearing (metalworking) — Shearing is a metalworking process which cuts stock without the formation of chips or the use of burning or melting. Strictly speaking, if the cutting blades are straight the process is called shearing; if the cutting blades are curved then they… …   Wikipedia

  • Taxonomy of manufacturing processes — This tree lists various manufacturing processes arranged by similarity of function.#Casting ##Sand casting ##Plastic mold ##Shell mold ##Investment casting (lost wax, precision) ##Permanent mold ##Centrifugal casting ##Die casting ##Slush or… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”