Damp (structural)

Damp (structural)
Detail showing some of the causes of damp penetration

Structural dampness refers to the presence of unwanted moisture in the structure of a building, either the result of intrusion from outside or condensation from within the structure.

A high proportion of damp problems in buildings are caused by the "big three"; condensation, rain penetration, and rising damp,[1] although other causes of dampness such as pipe leakage and construction moisture should not be overlooked.

Contents

Symptoms

Dampness tends to cause secondary damage to a building. The unwanted moisture enables the growth of various fungi in wood, causing rot or mold health issues and may eventually lead to sick building syndrome. Plaster and paint deteriorate and wallpaper loosens. Stains, from the water, salts and from mold, mar surfaces. The highest airborne mold concentrations are found in buildings where significant mold infestation has occurred, usually as a result of severe water intrusion or flood damage.[Godish 1] Molds can grow on almost any surface and occurs where there is a lot of moisture from structural problems such as leaky roofs or high humidity levels.[Mold Effects 1] Airborne mold concentrations have the potential to be inhaled and cause serious health effects in humans.

Externally, mortar may crumble and salt stains may appear on the walls. Steel & iron fasteners rust. It may also cause a poor indoor air quality and respiratory illness in occupants.[2] In extreme cases, mortar or plaster may fall away from the affected wall.

Health Effects of Damp Structural

Asthma is one of the most common health effects associated with structural dampness. Asthma is heightened due to condensation, moisture, humidity, and water intrusion, which all contribute to indoor moisture. Mold infestation is a major trigger for asthma. Aside asthma, other health concerns of mold are infections, allergenic or immunological illness, and nonallergic illness.[Godish 1] Asthma is also triggered by the sensitization of dust mites accruing humid, wet regions of a structure.[Godish 1] Another health effect associated with structural dampness is the presence of bacteria in an indoor environment. Bacteria requires water to grow and multiply. Bacteria is a source for the transmission of diseases, therefore putting occupants’ health at risk by water intrusion into the indoor environment. Water removal and drying of wet building materials within 2 days will likely prevent mold and bacteria growth, therefore reducing occupants’ vulnerability to disease.[Mold Effects 2]

A 2009 World Health Organisation report entitled "Children Living in Homes With Problems of Damp" [3] stated that:

"Excess moisture leads – on almost all indoor materials – to growth of microbes such as moulds, fungi and bacteria, which subsequently emit spores, cells, fragments and volatile organic compounds into the indoor air. Moreover, dampness initiates chemical and/or biological degradation of materials, which also causes pollution of the indoor air. Exposure to microbial contaminants is clinically associated with respiratory symptoms, allergies, asthma and immunological reactions. Dampness has therefore been suggested to be a strong and consistent indicator of risk for asthma and respiratory symptoms such as cough and wheeze."

Identification

A wide range of instruments and techniques can be used to investigate the causes of moisture in building materials. When used correctly, they can provide a valuable aid to investigation.[4] The competence and experience of the person undertaking the damp investigations is of greater importance than the kit he or she carries.

Processes for diagnosing rising Damp in buildings is set out in BRE Digest 245.

All of the above should be considered during any assessment for damp related defects in buildings.

Prevention and treatment

Most forms of dampness can be prevented by thoughtful building design and careful construction. In the UK, well built modern houses include damp proofing in the form of a synthetic damp-proof course (DPC), about 15 cm above ground level, to act as a barrier through which water cannot pass. Slate or "engineering bricks" with a low porosity were often used for the first few courses above ground level, and these can in theory help minimise the problem.

There are many approaches to the treatment of dampness in existing buildings. Key to the selection of an appropriate treatment is a correct diagnosis of the types of dampness affecting a building. Details of possible treatments for specific types of dampness are covered in the sections below.

The cause of the dampness must first be eliminated, by providing better drainage or fixing leaking pipes. BRE Digest 245[5] describes several methods of treating rising damp, including the use of land-drains and the insertion of physical and chemical DPCs. Then, any affected plaster or mortar must be removed, and the wall treated, before replacing the plaster and repainting.

The major damp treatment authorities within the U.K. are The British Wood Preserving and Damp-proofing Association (BWPDA) and The Property Care Association.

Humidity

Humidity occurs in indoor environments due to building related causes. Porous walls, rising damp, and leaks in the building are determinants for structural dampness due to elevated humidity levels.[Godish 1] The construction of the building can also lead to humidity and unwanted moisture in the indoor environment.[Moisture Dynamics 1] Wet materials, such as lumber stored unprotected outdoors before construction, can lead to increased humidity indoors for up to the second year of occupancy in the building.[Moisture Dynamics 1] Most commonly in residences, elevated relative humidity is produced by poor drainage systems.[Godish 1] This leads to dampness in substructures such as crawlspaces and basements. The dampness results in vaporization where water vapor is transmitted into the building's interiors.[Godish 1] Water vapor may enter the building through supply air ducts in building slabs and circulated by warm forced air.[Godish 1] Water vapor can also enter a building through leaky return air ducts in homes with crawlspaces.[Godish 1]

Human occupancy adds a significant amount of humidity to the indoor environment. Personal activity as basic as breathing and perspiration add moisture to an indoor space. [Humidity Cooling 1] Cooking and showering raise humidity levels in the indoor environment, which directly affects the structural dampness of a home. Aspects of the home can also increase the humidity of a space. Items such as aquariums, indoor swimming pools, hot tubs, and even indoor plants add to the humidity of an indoor space. [Moisture Dynamics 1] All of these attributes can increase the humidity of a home beyond it’s recommended thirty to fifty percent. [Moisture Dynamics 1]

Humidity levels in an indoor environment need to be accounted for based upon season and temperature. If humidity levels do not agree with the time of the year and the temperature during seasons, mold infestation and deterioration of the building will occur due to moisture. An acceptable humidity level in indoor spaces ranges from twenty to sixty percent year round.[Air Quality 1] However, levels less than twenty percent in the winter and levels higher than sixty percent in the summer are deemed unacceptable for indoor air quality.[Air Quality 1] Structural dampness is likely to occur as well as an increase of health risks associated with moisture damage.

Prevention and Treatment

There are strategies to prevent water infiltration due to humidity into structures, as well as ways to treat human occupancy practices regarding humidity. Vapor retarders are materials that can be used to restrain uncontrolled airflow and water vapor into an indoor space.[Moisture Dynamics 1] Vapor retarders are used to decrease the rate and amount of water vapor diffusion through ceilings, walls, and floors caused by humidity.[Moisture Dynamics 1] It is made of thin, flexible materials and it’s coatings can be installed by trowels or brushes.[Moisture Dynamics 1] Utilizing vapor retarders in a building prevents structural dampness from occurring or continuing if it already exists. A strategy for reducing humidity levels in an indoor environment is by altering occupant activity and indoor mechanics. Kitchens and bathrooms need to have their own vents.[Moisture Dynamics 1] Additionally, washing machines need to be vented outdoors.[Moisture Dynamics 1] Both of these are important in order to decrease indoor moisture due to humidity caused by the activities occurring in these indoor spaces. Moisture sources, such as hot tubs or indoor swimming pools, should be covered by airtight lids when not in use, thus humidity levels stay low in the indoor environment. [Moisture Dynamics 1]

Condensation

Condensation comes from water vapour within the building. Common sources may include cooking, bathing etc. The moisture in the air condenses on cold surfaces. Buildings with poorly insulated walls are very prone to this problem. It often causes damage similar to damp in a building and often appears in similar places. This is because it occurs in the "dead air" pockets that accumulate in both horizontal and vertical corners (i.e. out of circulating air patterns).

Moisture condenses on the interiors of buildings due to specific interactions between the roof and wall. Leaks most commonly occur on flat-roofed buildings.[Godish 1] Certain building materials and mechanisms can be used to prevent condensation from occurring in these areas, therefore reducing structural dampness and potential mold infestation. In many cases, the insulation between the roof and wall is compressed, leading to a decrease in thermal resistance.[Moisture Dynamics 1] Due to the lack of thermal resistance, condensation occurs, which leads to water damage in the indoor environment. In most cases where moisture is not addressed quickly enough, mold and mildew develop. Another issue is that wind washing up into the crevice where the roof and wall intersect reduces the efficiency of the insulation.[Roof Surface 1] This results in condensation and risk for mold growth.

In the United Kingdom, condensation problems are particularly common between October and March - to the extent that this period is often referred to as the "condensation season."[6]

Identification of condensation

If it is suspected that the problem is condensation, then a room should be sealed off with a dehumidifier left running for the recommended time and then further instrument tests made. If the dampness has disappeared, then condensation is very likely the problem.

Alternatively Humiditect cards or dataloggers (measuring air humidity, air temperature, and surface temperature) can be used as tools for diagnosing a condensation problem.[7]

Treatment

Typical remedies for condensation include increasing background heat and ventilation,[8] improving the insulation of cold surfaces and reducing moisture generation (e.g. by avoiding the drying of clothes indoors).

Rain Penetration

Rain Penetration (also known as "penetrating damp") is a common form of dampness in buildings. It can occur through walls, roofs, or through openings (e.g. window reveals).[1]

Water will often penetrate the outer envelope of a building and appear inside. Common defects include.

  • Roof defects such as faulty flashing, cracked or missing slates or tiles.
  • Faults in the brickwork or masonry such as missing or cracked pointing. Porous bricks or stones.
  • Missing or defective mastic around windows and doors.
  • Blocked weep holes.
  • Missing or defective trays in cavity walls.

Walls

Rain penetration is most often associated with single-skin walls, but can also occur through cavity walls - e.g. by tracking across wall ties.[1]

Rising damp

Rising damp is the common term for the slow upward movement of water in the lower sections of walls and other ground-supported structures by capillary action. Although rising damp of up to 5 metres in height has been observed[9] the height of rise is typically much lower and is rarely above 1.5m. Rising damp has been a widely observed phenomenon for at least two hundred years. [10] There is also strong evidence to suggest that it was a problem understood by the Romans and Ancient Greeks.[11][12]

In simple terms rising damp occurs when ground water travels upwards through porous building materials such as brick, sandstone, or mortar, much in the same way that oil travels upwards through the wick of a lamp. The effect can easily be seen by simply placing a piece of porous brick, stone, or mortar in a shallow tray of water and observing how the water is absorbed into the porous material and is transported above the water line.

Rising damp can be identified by a characteristic "tide mark" on the lower section of affected walls. This tide mark is caused by soluble salts (particularly nitrates and chlorides) contained in the groundwater. Due to the effects of evaporation these salts accumulate at the "peak" of the rising damp.[13]

Historical Evidence of Rising Damp

The issue of rising damp has been a concern since ancient times.[11][14] The Roman Architect Vitruvius referred to the problem of dampness rising up walls and advised on how to construct buildings to avoid the problem.[15][16]

Rising damp is widely referred to in Victorian literature and the Public Heath Act of 1875 introduced the requirement for a damp-proof course in walls to prevent rising damp.[5] An entry in the British medical Journal from 1872 describes the phenomenon of rising damp as follows:

"Even if the rising damp be arrested by what is technically called an impervious damp-proof course, it will be frequently found that this is built in the wall too near the ground line, so that the heavy rain besplatters the ground and splashes above it. As time rolls on the surface of the ground also becomes elevated, and this damp course is soon lost to sight. Attempts have been made to remedy this evil of porous bricks by the substitution of the hard blue bricks of Staffordshire; and then it may often be noticed that the wet has only struck, sailor-like, across the mortar-joints and chequered the inside walls like a tartan plaid."[17]

The architect and social reformer, Thomas Worthington, described rising damp in his 1892 essay, "The Dwellings of the Poor: And Weekly Wage-Earners in and Around Towns":

"It should be borne in mind that damp walls absorb much more heat than dry ones and that they are frequent agents in causing rheumatism, kidney disease and colds. Rising damp from the ground may be prevented by most simple means. Six inches of good Portland cement concrete should cover the whole site of the dwelling, and concrete never less than nine inches thick should underlie all walls. A damp course should disconnect the whole of the foundations from the superstructure. This preventative may consist of a double layer of thick slates bedded in cement, or of patent perforated stone-ware blocks or of three-quarters of an inch of best asphalt."[18]

The Building Research establishment (BRE) in its review concludes that Rising Damp is a real problem.[1][5] [10] Indeed, Part C of the Building Regulations for England and Wales specifically calls for the inclusion of a damp-proof course in all new properties.[19]

The Case and Evidence Against Rising Damp

A number of people have expressed the view that rising damp is a myth. A former chairman of the construction arm of the Royal Institution of Chartered Surveyors (RICS), Stephen Boniface, has said that ‘true rising damp’ is a myth and chemically injected damp-proof courses (DPC) are ‘a complete waste of money’.[20]

Konrad Fisher's article "The Fraud of Rising Damp" points out that the historic city hall in Bamberg stands in the river Regnitz and its bridge remains dry without any chemical, mechanical or electronic damp-proof course.[21] However, evidence suggests that not all walls are capable of supporting rising damp, so merely observing that rising damp does not occur in a particular wall does not disprove its existence in other walls.[22][23][24]

In 1997 staff at Lewisham Council in South London were so convinced that rising damp is extremely rare or possibly a myth that they are offered a reward of £50 to anyone who could prove them wrong.[25]

How Rising Damp Occurs

According to Jurin's Law the maximum height of rise is inversely proportional to the capillary radius.[26] Taking a typical pore radius for building materials of 1 µm, Jurin's Law would give a maximum rise of about 15 m, however, due to the effects of evaporation, in practice the rise would be considerably lower.[26]

A "physical model" of rising damp was developed by Christopher Hall and William D Hoff in their paper "Rising damp: capillary rise dynamics in walls".[22] The analysis is based on experimentally well established properties of porous building materials and the physics of evaporation from building surfaces.[27] They state that model can be used to predict the height to which damp will rise in a wall, based on factors such as wall thickness, the sorptivity of the wall structure and the effect of evaporation. Further work has confirmed experimentally the importance of mortar properties in determining the height to which damp will rise in walls.[23] BRE Digest 245 lists several factors that can influence the height of the rise including rate of evaporation from the wall, pore sizes of the masonry, salt content of the materials and the soil, groundwater and degree of saturation, and use of heating within the property.[5] The effect of seasonal variations in evaporation rate on the height of moisture rise have been comprehensively described.[28]

A review of data and publications commissioned by the Property Care Association and carried out by the University of Portsmouth [10] concluded that "Rising damp is an age-old and ubiquitous problem." It also noted that "Records on observation and descriptions on this phenomenon date back to early times. It was identified as a public health issue in the second half of the 19th Century." The review looked at data and studies on rising damp from a number of countries including the United Kingdom, Portugal, Germany, Denmark, the Netherlands, Greece, Australia, and Malaysia.


Diagnosis of Rising Damp

The first step in assessing damp is to check for standing water. Removing water with good drainage will remove any form of dampness. Once done, and dampness remains, the next step is to look for the presence of a damp-proof course.[5] If a damp-proof course is present, it is likely to be functioning, as the materials from which damp proof courses are manufactured tend to have a long lifespan. However, it should be acknowledged that there are cases where existing damp proof courses fail for one reason or another.[5]

One method that is often used to determine if the source of dampness is rising damp (rather than other forms of dampness) is to look for the presence of salts - in particular a tell tale "salt band" or "tide mark" at the peak of the damp's rise. Although this is a useful indicator, it is not completely reliable as salts can enter the fabric of the wall in other ways - e.g. unwashed sea sand or gravel used in the construction of the wall.[1]

If there is no damp-proof course and rising damp is suspected (tide mark, moisture confined to lower section of wall etc...) then a number of diagnostic techniques can be used to determine the source of dampness. BRE Digest 245 states that the most satisfactory approach is to obtain samples of mortar in the affected wall using a drill and then analysing these samples do determine their moisture and salt content.[5] The fact that this technique is destructive to the wall finish often makes it unacceptable to homeowners. It is for this reason that electrical moisture meters are often used when surveying for rising damp. These instruments are unable to accurately measure the moisture content of masonry (they were developed for use on timber), however the patterns of readings that they provide can provide a useful indication of the source of dampness.[4]

Treatment of Rising Damp

In many cases, damp is caused by "bridging" of a damp-proof course that is otherwise working effectively. For example a flower bed next to an affected wall might result in soil being piled up against the wall above the level of the DPC. In this example, moisture from the ground would be able to ingress through the wall from the soil. Such a damp problem could be rectified by simply lowering the flower bed to below DPC level.

Where a rising damp problem is caused by a lack of a damp-proof course (common in buildings over approximately 100 years old) or by a failed damp-proof course (comparatively rare) there are a wide range of possible solutions available. These include:

  • Replacement physical damp proof course
  • Injection of a liquid or cream chemical damp proof course (DPC Injection)
  • Porous tubes
  • Electrical-osmotic systems
  • Land drainage

BRE Digest 245 suggests that with the exception of replacement physical DPCs, only methods of treatment with third party accreditation (E.g. British Board of Agreement Certificate) should be considered. It then goes on to state that the only method of currently satisfying this requirement is DPC injection and that "this is the only method which BRE considers suitable where insertion of a physical DPC is not possible."[5] The Royal Institute of Chartered Surveryors (RICS) publication "Remedying Damp" is more cautious about reliance on third party accredititation, casting doubt upon the validity of the test methods employed, arguing that trials are usually conducted using "specially built masonry panels - which do not match up in many respects to walls found in real properties," and that "if a DPC were proved to not work in a specially built masonry panel, this would be the more significant result."[29] The MOAT No 39 test[30] employed by the British Board of Agreement (BBA) in the UK is dismissed as "quite a clever test idea but in the author's opinion not actually replicating a real wall."[29] Furthermore, the point is made that "BBA testing is paid for by manufacturers, and the results are not thought to be publicly available."[31]

Replastering

Replastering will often be carried out as part of a rising damp treatment. Where plaster has become severely damaged by ground salts there is little argument about the need to replaster. However there is considerable debate about:

  1. The extent of replastering required
  2. The use of hard sand:cement renders to replaster as part of a rising damp treatment

BS6576:2005[32] states that "the function of the new plaster is to prevent hygroscopic salts that might be present in the wall from migrating through to its surface, while still allowing the wall to dry." However, writing in the RICS publication "Remedying Damp", Ralph Burkinshaw claims that, "the plaster is really there for two main reasons." He accepts the need for replastering when significant amounts of ground salts have built up in the existing plaster, however he then goes on to say that replastering is often carried out to make up for an unreliable chemical DPC. He also suggests that damp-proofers have an incentive to carry out more replastering than is strictly necessary as it allows them to finish the job without having to wait for walls to dry out, resulting in faster payment.[33]

Although the sand:cement renders typically installed as part of a rising damp treatment are very effective at holding back damp and ground salts, they have a number of disadvantages. These include an incompatibility with the soft bricks and mortars encountered in older buildings and a lack of insulation properties compared with more traditional plasters, resulting in an increased risk of condensation. Replastering is also one of the most expensive parts of a rising damp treatment.

Porous renders to German WTA specification 2-2-91 can be used as an alternative to dense sand-cement renders. These have a minimum porosity of 40% of total volume. Salts crystallise in these pores rather than on the plaster surface, avoiding decorative spoiling. Such plasters offer a better solution than dense sand-cement renders when used on moderately salt-contaminated walls as their porous nature gives them insulation properties, resulting in a warmer surface temperature and making condensation problems less likely to occur. However, when used on heavily salt contaminated walls they may need to be replaced frequently as they lose effectiveness once all the pores have become filled with crystallised salt.[34]

References

  1. ^ a b c d e Trotman, Peter; Chris Sanders and Harry Harrison. Understanding Dampness. BR466. Building Research Establishment. ISBN 1 86081 686 x. 
  2. ^ WHO guidelines for indoor air quality : dampness and mould. World Health Organisation. ISBN 9789289041683. 
  3. ^ Children Living in Homes With Problems of Damp. World Health Organisation. http://www.euro.who.int/__data/assets/pdf_file/0005/97007/enhis_factsheet09_3_5.pdf. 
  4. ^ a b "Use of electrical moisture meters". http://www.buildingpreservation.com/index.php?option=com_content&view=article&id=50&Itemid=26. 
  5. ^ a b c d e f g h Trotman, Peter. Rising damp in walls, diagnosis and treatment. BRE Digest 245. Building Research Establishment. ISBN 978-1-84806-012-8. 
  6. ^ The Condensation Season - October until March, Peter MacDonald - Condensation Explained.
  7. ^ How can I check for condensation?, Peter MacDonald - Condensation Explained.
  8. ^ Burkinshaw, Ralf. Remedying Damp. RICS Books. p. 151. ISBN 978-1-84219-305-1. 
  9. ^ Damp Buildings Old and New - G and I Massari - ISBN: 9290771119
  10. ^ a b c "A Review of Rising Damp in Masonry Buildings". http://www.property-care.org/images/stories/A_Review_of_Rising_Damp_in_Masonry_Buildings.pdf. 
  11. ^ a b "Roman Damp Proof Course". http://www.geolocation.ws/v/W/4d588b6c1d41c86ece058995/a-roman-damp-proof-course-at-hardknott/en. 
  12. ^ The Roman Villa (Villa Urbana) - Alfred Frazer - ISBN: 0924171596 - p. 36
  13. ^ Oliver, Alan. Dampness in Buildings. BSP Professional Books. ISBN 0-632-01932-8. 
  14. ^ The Roman Villa (Villa Urbana) - Alfred Frazer - ISBN: 0924171596 - p. 36
  15. ^ A History of Architectural Conservation - Jukka Jokilehto - ISBN: 0750637935 - p. 3
  16. ^ Roman Baths in Britain - Tony Rook - ISBN: 0747801576 - p. 14
  17. ^ "Damp Houses," British Medical Journal, May 25, 1872, p. 558
  18. ^ The Dwellings of the Poor: And Weekly Wage-Earners in and Around Towns - Thomas Locke Worthington - ISBN 978-0559706295, p. 105
  19. ^ "Building Regulations - Part C". http://www.planningportal.gov.uk/england/professionals/buildingregs/technicalguidance/bcresistancetocontaminantsand241/bcapproveddocuments1. 
  20. ^ "Rising damp is a myth, says former RICS chief". http://www.architectsjournal.co.uk/news/daily-news/-rising-damp-is-a-myth-says-former-rics-chief/5204095.article. 
  21. ^ "The Fraud of Rising Damp". http://www.konrad-fischer-info.de/2auffen.htm. 
  22. ^ a b "Proceedings of the Royal Society - Rising damp: capillary rise dynamics in walls - Christopher Hall and William D Hoff". http://rspa.royalsocietypublishing.org/content/463/2084/1871.full. 
  23. ^ a b "Construction and Building Materials - Rising Damp in Masonry Walls and the Importance of Mortar Properties - Eric Rirsch and Zhongyi Zhang". http://www.safeguardeurope.com/papers-articles/rising-damp-in-masonry-walls.php. 
  24. ^ "Construction and Building Materials - Evaluation of mortar samples obtained from UK houses treated for rising damp - Eric Rirsch, James MacMullen and Zhongyi Zhang". http://www.safeguardeurope.com/papers-articles/evaluation-mortar-samples-rising-damp.php. 
  25. ^ "Lewisham Council Article". http://www.independent.co.uk/news/business/property-rising-damp-no-such-thing-1295773.html. 
  26. ^ a b Alfano, G; C Chiancarella, E Cirillo, I Fato, F Martellotta (2006). "Long-term performance of chemical damp-proof courses: Twelve years of laboratory testing". Building and Environment 41 (8): 1060–1069. doi:10.1016/j.buildenv.2005.04.017. 
  27. ^ "Water Transport in Brick, Stone and Concrete - Christopher Hall and William D Hoff". http://www.taylorandfrancis.com/books/details/9780419228905/. 
  28. ^ "Proceedings of the Royal Society - Moisture dynamics in walls:". http://rspa.royalsocietypublishing.org/content/467/2125/194.full. 
  29. ^ a b Burkinshaw, Ralph. Remedying Damp. RICS Books. p. 85. ISBN 978-1-84219-305-1. 
  30. ^ The Assessment of Damp-proof Course Systems for Existing Buildings, MOAT No.39. British Board of Agrement. 
  31. ^ Burkinshaw, Ralf. Remedying Damp. RICS Books. p. 85. ISBN 978-1-84219-305-1. 
  32. ^ BS6576:2005, Code of practice for diagnosis of rising damp in walls of buildings and installation of chemical damp proof courses. BSI. p. 9. ISBN 0580468674. 
  33. ^ Burkinshaw, Ralf. Remedying Damp. RICS Books. p. 81. ISBN 978-1-84219-305-1. 
  34. ^ WTA Merkblatt 2-6-99/D. Endgültige Fassung Juli 2001 - ISBN 978-3-8167-6794-7
  1. ^ a b c d e f g h i Godish, Thad (2001). Indoor Environmental Quality. CRC Press. pp. 178. ISBN 1566704022. 
  1. ^ a b c d e f g h i j k Prowler, Don. "Mold and Moisture Dynamics". WBDG: Whole Building Design Guide. http://www.wbdg.org/resources/moisturedynamics.php. Retrieved 11/7/11. 
  1. ^ "Why Humidity Matters when Cooling". Nature's Cooling Solutions. http://naturescoolingsolutions.com/ecobreeze/?page_id=193. Retrieved 13 November 2011. 
  1. ^ "Mold". Office of Environmental Health, Safety, and Toxicology. Washington State Department of Health. http://www.doh.wa.gov/ehp/ts/iaq/got_mold.html. Retrieved 17 November 2011. 
  2. ^ "Mold and Water Intrusion". Department of Environmental Health and Safety. University of Colorado at Boulder. http://www.colorado.edu/ehs/pdf/ECIH.Mold%20and%20Water%20Intrusion.11_08.pdf. Retrieved 17 November 2011. 
  1. ^ "The Leaky Roof Surface". Living With My Home. Pillar To Post, Inc.. http://livingwithmyhome.com/201-home-tips/pillar-to-post-leaky-roof.aspx. Retrieved 20 November 2011. 
  1. ^ a b "Guidlines for Indoor Air Quality". Illinois Department of Public Health. http://www.idph.state.il.us/envhealth/factsheets/indoorairqualityguide_fs.htm. Retrieved 20 November 2011. 

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Rising damp (structural) — Rising damp is a condition caused by ground moisture rising up a masonry wall by capillary action. It occurs where there is no damp proof course (DPC) or where the DPC has been damaged or bridged. Where present, moisture can rise up the wall to a …   Wikipedia

  • Damp (disambiguation) — Damp is an alternate term for Moisture. Damp or DAMP may also refer to: Damp (structural) Damp, Germany, a municipality in Schleswig Holstein, Germany Damp (album), a compilation album by Foetus Damp (mining), a gaseous product formed in coal… …   Wikipedia

  • Death damp — Death Death (d[e^]th), n. [OE. deth, dea[eth], AS. de[ a][eth]; akin to OS. d[=o][eth], D. dood, G. tod, Icel. dau[eth]i, Sw. & Dan. d[ o]d, Goth. dau[thorn]us; from a verb meaning to die. See {Die}, v. i., and cf. {Dead}.] 1. The cessation of… …   The Collaborative International Dictionary of English

  • Moisture — Damp redirects here. For other uses, see Damp (disambiguation). Dew on a spider web Humidity is the amount of moisture the air can hold before it rains. Moisture refers to the presence of a liquid, especially water, often in trace amounts. Small… …   Wikipedia

  • Dry rot treatment — refers to the techniques used to eliminate dry rot fungus and alleviate the damage done by the fungus to human built wooden structures. The commonly held view of an outbreak of the dry rot fungus (Serpula lacrymans) within a building is that it… …   Wikipedia

  • damping — damp·ing (dămʹpĭng) n. The capacity built into a mechanical or electrical device to prevent excessive correction and the resulting instability or oscillatory conditions. * * * In physics, the restraint of vibratory motion, such as mechanical… …   Universalium

  • art conservation and restoration — Maintenance and preservation of works of art, their protection from future damage, deterioration, or neglect, and the repair or renovation of works that have deteriorated or been damaged. Research in art history has relied heavily on 20th and… …   Universalium

  • painting — /payn ting/, n. 1. a picture or design executed in paints. 2. the act, art, or work of a person who paints. 3. the works of art painted in a particular manner, place, or period: a book on Flemish painting. 4. an instance of covering a surface… …   Universalium

  • Basement — This article is about the section of a building. For other uses, see Basement (disambiguation). An unfinished basement used for storage and exercise equipment …   Wikipedia

  • fern — fernless, adj. fernlike, adj. /ferrn/, n. any seedless, nonflowering vascular plant of the class Filicinae, of tropical to temperate regions, characterized by true roots produced from a rhizome, triangular fronds that uncoil upward and have a… …   Universalium

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”