Design and manufacturing of gears

Design and manufacturing of gears

Gear design is the process of designing a gear. Designing is done prior to manufacturing and includes calculation of the gear geometry, taking into account gear strength, wear characteristic of the gear teeth, material selection, gear alignment and provision for lubrication of gear.

Contents

Gear

A gear is a rotating machine part which has cut teeth, that mesh with another toothed part in order to transmit torque. The cut teeth are also called 'cogs'. Gears are one of the most important parts of any machine or a mechanism. Some of the sectors in which gears play a vital role are:

  • Turbine plant
  • Hot and Cold Rolling
  • Construction machinery
  • Elevator industry

Gear tooth terminology

Gear tooth terminology

Standard system of Gear Teeth

In a gear drive, two types of curves, the cycloidal and the involute, are generally used. In a gear drive, the shape of the tooth depends upon the pressure angle. Gears of involute profile with 14.5°,20° full-depth and 20° stub pressure angles are most commonly used in industries. A 20° pressure angle full-depth involute gear tooth has various advantages over the other pressure angles. BIS has recommended the use of 20° pressure angle full depth involute gear tooth.

Design Considerations[1]

The accuracy of the output of a gear depends on the accuracy of its design and manufacturing.The correct manufacturing of a gear requires a number of prerequisite calculations and design considerations.The design considerations taken into account before manufacturing of gears are:

  • Strength of the gear in order to avoid failure at staring torques or under dynamic loading during running conditions.
  • Gear teeth must have good wear characteristics.
  • Selection of material combination.
  • Proper alignment and compactness of drive
  • Provision of adequate and proper lubrication arrangement.

Selection of Materials

The gear material should have the following properties:

  • High tensile strength to prevent failure against static loads
  • High endurance strength to withstand dynamic loads
  • Low coefficient of friction
  • Good manufacturability

Generally cast iron,steel,brass and bronze are preferred for manufacturing metallic gears with cut teeth.Where smooth action is not important,cast iron gears with cut teeth may be employed.Commercially cut gears have a pitch line velocity of about 5 metre/second.For velocities larger than this,gear sets with non metallic pinions as one member are used to eliminate vibration and noise.Non-metallic materials are made of various materials such as treated cotton pressed and and moulded at high pressure,synthetic resins of the phenol type and raw hide.Moisture affects raw hide pinions.gears made of phenolic resins are self supporting on the other hand other two types are supported by metal side plates at both ends of the plate.Large wheels are made with fretting rings to save alloy steels.Wheel centre is commonly cast from cast iron.The ring is forged or roll expanded from steel of the respective grade specified by the tooth design.

Gear wheel proportions

A gear has three important parts

  • Hub
  • Web or arms
  • Rim

Hub of gears are of two types,solid or split.The advantage of split hub is that it reduces the cooling stresses in the gear and facilitates the mounting of the gear on the shaft.The solid hub gear is to be mounted overhung on the shaft.The key is placed under the arm in case of solid hub while in case of split hub,the key is placed at right angles to the hub joint. Small gears up to 250 mm pitch circle diameter are built with a web,which joins the hub and the rim.The thickness of the web of the gear should be such that it is capable of transmitting the torque without shearing off at the hub where it joins.The gear is designed such that the thickness of its web is equal to half the circular pitch.Gear of larger diameter are provided with arms.The number of arms depends on the pitch circle diameter of the gear.Following are the prevailing practices of the number of arms and gear diameters

Gear diameter(mm) Arms
300-500 4-5
500-1500 6
1500-2400 8
>2400 10-12


While calculating the dimensions of the arms it is assumed that they transmit the stalling torque safely.Elliptical cross sections are preferred for lighter loads while remaining cross sections are used for large and heavy gears.The following aspects are considered while determining cross sectional diameter of the arm.

Cross section area of arm.png

Empirical formulas are used to determine the rim thickness.

Rim  thickness = Module \sqrt{\frac{N}{2N_A}},

where N is the number of teeth and NA are the number of arms.
A good design is a one in which the rim has a central rib of thickness equal to half the circular pitch.
If the lay out of the shaft is known,the diameter of the gear shaft can be calculated.Toothed wheels fixed on the shaft are fitted by interference-for example,press or light press fit.For impact load or speeds above 2000 r.p.m. press fit is employed.If the wheel is to be removed from the shaft medium fit are used.

The following types of gears are most commonly used in industry for power transmission purposes:

  • Spur gears
  • Helical gears
  • Bevel gears
  • Worm and worm gears

Spur Gear[2]

Representation of spur gear

A gear having straight teeth along the axis is called a spur gear.They are used to transmit power between two parallel shafts as shown in the adjacent figure.A rack is a straight tooth gear which can be thought of as a segment of spur gear of infinite diameter.

Design of spur gear

The prime requirement of a gear drive is to transmit power at a particular velocity ratio for certain working condition,such as,operating time,nature of load,etc.The following points must be considered while designing a gear drive:

  • Highest static load acting on the gear tooth due to high starting torque
  • Dynamic load at normal running conditions due to profile error on the tooth.
  • Wear characteristics of the tooth for increasing its life

Besides the above basic requirements,the following aspects are also considered:

  • Lubrication of teeth
  • alignment of gears
  • Stress concentration at the root of the teeth
  • Deflection of gear teeth and shaft should be specified

Force Analysis

In a gear drive,power is transmitted by means of a force exerted by the tooth of the driving gear on the mating tooth of the driven gear.The law of gearing states that,the exerted force Fn is always normal to the tooth surface and acts along the pressure angle line.
Force on a gear tooth
The normal force Fn as shown in the above figure,acting along the pressure line,can be resolved into two components,tangential force Ft and radial force Fr.Thus,

Ft=Fncosα and Fr=Fnsinα=Ft,tanα where α is the pressure angle.

Ft is responsible for transmitting torque and hence the power while the Fr is called the separating force,which always acts towards the centre of the gear.
In the force analysis of a gear drive,an assumption is made that the tangential force remains constant in magnitude as the contact between two teeth moves from top of the tooth to its bottom.The torque transmitted by Ft with respect to the centre of the gear is

T = {\frac{F_td_1}{2}},

Also by using the relation P = Ft×v, the tangential force responsible for transmitting power can be obtained,where

P, is the power(kW)
v, is the pitch line velocity(m/s)
Ft, is tangential force(kN).

Beam strength of spur gear tooth

Force acting on a gear tooth

The continuous change in the point of application of load on the tooth profile and the change in magnitude and direction of the applied load make accurate stress analysis of a gear tooth a complicated problem.In 1892,Wilfred Lewis published a paper titled,"The investigation of the strength of gear tooth",in which he derived an equation for determining the approximate stress in a gear tooth by treating it as a cantilever beam of uniform strength.
The following assumptions are made for the beam strength calculation:

  • The tangential component,Ft,is uniformly distributed across the face width.But practically the distribution is non- uniform.This assumption is valid for small face widthsb,i.e.

9.5m≤b≤12.5m, where m is the module of the gear.

  • The effect of the radial componentFr,which produces direct compressive strength ,is neglected.
  • The maximum stress is assumed to occur when the entire load is at the tip of the tooth.
  • The tooth is assumed to be a simple cantilever beam.
  • The effect of stress concentration and manufacturing error are neglected.

References

  1. ^ Pandya, N.C. (1981). Elements of Machine Design. India: Charotar Publishing House. pp. 713–735. 
  2. ^ Sharma, C.S. (2010). Design of Machine Elements. India: PHI Learning Private Limited. pp. 399–426. ISBN 978-81-203-1955-4. 

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Business and Industry Review — ▪ 1999 Introduction Overview        Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… …   Universalium

  • clothing and footwear industry — Introduction also called  apparel and allied industries,  garment industries,  or  soft goods industries,         factories and mills producing outerwear, underwear, headwear, footwear, belts, purses, luggage, gloves, scarfs, ties, and household… …   Universalium

  • Wind turbine design — An example of a wind turbine, this 3 bladed turbine is the classic design of modern wind turbines Wind turbines History Design …   Wikipedia

  • Lenses for SLR and DSLR cameras — This article is about photographic lenses for single lens reflex film cameras (SLRs) and digital single lens reflex cameras (DSLRs). Furthermore, the emphasis is on modern lenses for 35 mm film SLRs and for DSLRs with sensor sizes less than or… …   Wikipedia

  • Technical and Further Education — or TAFE (pronounced [tæɪf] ) institutions provide a wide range of predominantly vocational tertiary education courses in Australia. Fields covered include hospitality, tourism, construction, engineering, secretarial skills, visual arts, computer… …   Wikipedia

  • Derailleur gears — Transmission types Manual Sequential manual Non synchronous Preselector Automatic Manumatic Semi automatic Electrohydraulic Dual …   Wikipedia

  • Science and inventions of Leonardo da Vinci — Infobox Artist name = Leonardo da Vinci imagesize = 200px caption = The Vitruvian Man by Leonardo is possibly the best known drawing in the world. birthname = Leonardo di Ser Piero birthdate = birth date|1452|4|15|mf=y flagicon|ITA Anchiano,… …   Wikipedia

  • List of fictional elements, materials, isotopes and atomic particles — This list contains chemical elements, materials, isotopes or (sub)atomic particle that exist primarily in works of fiction (usually fantasy or science fiction). No actual periodic elements end in ite , though many minerals have names with this… …   Wikipedia

  • Wedding of Prince William and Catherine Middleton — Duke and Duchess of Cambridge waving to the crowd at the Mall sh …   Wikipedia

  • Centre for Fire, Explosive and Environment Safety — Infobox Laboratory name = Centre for Fire, Explosive and Environment Safety motto = logo = established = 1992 city = Delhi, India research field = type = director = J.C.Kapoor staff = budget = operating agency = DRDO affiliations = address = Brig …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”