Miller theorem

Miller theorem

Miller theorem refers to the process of creating equivalent circuits. It asserts that a floating impedance element supplied by two voltage sources connected in series may be split into two grounded elements with corresponding impedances. There is also a dual Miller theorem with regards to impedance supplied by two current sources connected in parallel. The two versions are based on the two Kirchhoff's circuit laws.

Miller theorems are not only pure mathematical expressions. These arrangements explain important circuit phenomena about modifying impedance (Miller effect, virtual ground, bootstrapping, negative impedance, etc.) and help designing and understanding various commonplace circuits (feedback amplifiers, resistive and time-dependent converters, negative impedance converters, etc.) They are useful in the area of circuit analysis especially for analyzing circuits with feedback[1] and certain transistor amplifiers at high frequencies.[2]

There is a close relationship between Miller theorem and Miller effect: the theorem may be considered as a generalization of the effect and the effect may be thought as of a special case of the theorem.

Contents

Miller theorem (for voltages)

Definition

Miller theorem establishes that in a linear circuit, if there exists a branch with impedance Z, connecting two nodes with nodal voltages ­V1 and V2, we can replace this branch by two branches connecting the corresponding nodes to ground by impedances respectively Z/(1 − K) and KZ/(K − 1), where K = V2/V1. Miller theorem may be proved by using the equivalent two-port network technique to replace the two-port to its equivalent and by applying the source absorption theorem.[3] This version of Miller theorem is based on Kirchhoff's voltage law; for that reason, it is named also Miller theorem for voltages.

Explanation

Miller theorem implies that an impedance element is supplied by two arbitrary (not necessarily dependent) voltage sources that are connected in series through the common ground. In practice, one of them acts as a main (independent) voltage source with voltage V1 and the other – as an additional (linearly dependent) voltage source with voltage V2 = KV1. The idea of Miller theorem (modifying circuit impedances seen from the sides of the input and output sources) is revealed below by comparing the two situations – without and with connected an additional voltage source V2.

If V2 was zero (there was not a second voltage source or the right end of the element with impedance Z was just grounded), the input current flowing through the element would be determined, according to Ohm's law, only by V1

I_{in0} = \frac{V_1}{Z}

and the input impedance of the circuit would be

Z_{in0} = \frac{V_1}{I_{in0}} = Z.

As a second voltage source is included, the input current depends on both the voltages. According to its polarity, V2 is subtracted or added from/to V1; so, the input current decreases/increases

I_{in} = \frac{V_1 - V_2}{Z} = \frac{(1 - K)}{Z}{V_1} = {(1 - K)}{I_{in0}}

and the input impedance of the circuit seen from the side of the input source accordingly increases/decreases

Z_{in} = \frac{V_1}{I_{in}} = \frac{Z}{1-K}.

So, Miller theorem expresses the fact that connecting a second voltage source with proportional voltage V2 = KV1 in series with the input voltage source changes the effective voltage, the current and respectively, the circuit impedance seen from the side of the input source. Depending on the polarity, V2 acts as a supplemental voltage source helping or opposing the main voltage source to pass the current through the impedance.

Besides by presenting the combination of the two voltage sources as a new composed voltage source, the theorem may be explained by combining the actual element and the second voltage source into a new virtual element with dynamically modified impedance. From this viewpoint, V2 is an additional voltage that artificially increases/decreases the voltage drop Vz across the impedance Z thus decreasing/increasing the current. The proportion between the voltages determines the value of the obtained impedance (see the tables below) and gives in total six groups of typical applications.

Subtracting V2 from V1
V2 vs V1
V2 = 0
0 < V2 < V1
V2 = V1
V2 > V1
Impedance
normal
increased
infinite
negative with current inversion
Adding V2 to V1
V2 vs Vz
V2 = 0
0 < V2 < Vz
V2 = Vz
V2 > Vz
Impedance
normal
decreased
zero
negative with voltage inversion

The circuit impedance seen from the side of the output source may be defined by the same reasonings if the voltages V1 and V2 are swapped and the coefficient K is replaced by 1/K

Z_{in2} = \frac{{K}{Z}}{K-1}.

Implementation

A typical implementation of Miller theorem based on a single-ended voltage amplifier

Most frequently, Miller theorem may be observed in and implemented by an arrangement consisting of an element with impedance Z connected between the two terminals of a grounded general linear network.[2] Usually, a voltage amplifier with gain of AV = K serves as such a linear network but also other devices can play this role: a man and a potentiometer in a potentiometric null-balance meter, an electromechanical integrator (servomechanisms using potentiometric feedback sensors), etc. In the amplifier implementation, the input voltage Vi serves as V1 and the output voltage Vo – as V2. In many cases, the input voltage source has some internal impedance Zint or an additional input impedance is connected that, in combination with Z, introduces a feedback. Depending on the kind of the amplifier (non-inverting, inverting or differential), the feedback can be positive, negative or mixed.

The Miller amplifier arrangement has two aspects:

  • the amplifier may be thought as an additional voltage source converting the actual impedance into a virtual impedance (the amplifier modifies the impedance of the actual element)
  • the virtual impedance may be thought as an element connected in parallel to the amplifier input (the virtual impedance modifies the amplifier input impedance).

Applications

The introduction of an impedance that connects amplifier input and output ports adds a great deal of complexity in the analysis process. Miller theorem helps reducing the complexity in some circuits particularly with feedback[2] by converting them to simpler equivalent circuits. But Miller theorem is not only an effective tool for creating equivalent circuits; it is also a powerful tool for designing and understanding circuits based on modifying impedance by additional voltage. Depending on the polarity of the output voltage versus the input voltage and the proportion between their magnitudes, there are six groups of typical situations. In some of them, Miller phenomenon appears as desired (bootstrapping) or undesired (Miller effect) unintentional effects; in other cases it is intentionally introduced.

Applications based on subtracting V2 from V1

In these applications, the output voltage Vo is inserted with an opposite polarity in respect to the input voltage Vi travelling along the loop (but in respect to ground, the polarities are the same). As a result, the effective voltage across and the current through the impedance decrease; the input impedance increases.

Increased impedance is implemented by a non-inverting amplifier with gain of 0 < Av < 1. The (magnitude of) output voltage is less than the input voltage Vi and partially neutralizes it. Examples are imperfect voltage followers (emitter, source, cathode follower, etc.) and amplifiers with series negative feedback (emitter degeneration), whose input impedance is moderately increased.

The op-amp non-inverting amplifier is a typical circuit with series negative feedback based on Miller theorem where the op-amp differential input impedance is apparently increased up to infinite

Infinite impedance uses a non-inverting amplifier with Av = 1. The output voltage is equal to the input voltage Vi and completely neutralizes it. Examples are potentiometric null-balance meters and op-amp followers and amplifiers with series negative feedback (op-amp follower and non-inverting amplifier) where the circuit input impedance is enormously increased. This technique is referred to as bootstrapping and is intentionally used in biasing circuits, input guarding circuits,[4] etc.

Negative impedance obtained by current inversion is implemented by a non-inverting amplifier with Av > 1. The current changes its direction as the output voltage is higher than the input voltage. If the input voltage source has some internal impedance Zint or if it is connected through another impedance element, a positive feedback appears. A typical application is the negative impedance converter with current inversion (INIC) that uses both negative and positive feedback (the negative feedback is used to realize a non-inverting amplifier and the positive feedback – to modify the impedance).

Applications based on adding V2 to V1

In these applications, the output voltage Vo is inserted with the same polarity in respect to the input voltage Vi travelling along the loop (but in respect to ground, the polarities are opposite). As a result, the effective voltage across and the current through the impedance increase; the input impedance decreases.

Decreased impedance is implemented by an inverting amplifier having some moderate gain, usually 10 < Av < 1000. It may be observed as an undesired Miller effect in common-emitter, common-source and common-cathode amplifying stages where effective input capacitance is increased. Frequency compensation for general purpose operational amplifiers and transistor Miller integrator are examples of useful usage of Miller effect.

The op-amp inverting amplifier is a typical circuit with parallel negative feedback based on Miller theorem where the op-amp differential input impedance is apparently decreased up to zero

Zeroed impedance uses an inverting (usually op-amp) amplifier with enormously high gain Av → ∞. The output voltage is almost equal to the voltage drop VZ across the impedance and completely neutralizes it. The circuit behaves as a short connection and a virtual ground appears at the input; so, it should not be driven by a constant voltage source. For this purpose, some circuits are driven by a constant current source or by a real voltage source with internal impedance: current-to-voltage converter (transimpedance amplifier), capacitive integrator (named also current integrator or charge amplifier), resistance-to-voltage converter (a resistive sensor connected in the place of the impedance Z). The rest of them have additional impedance connected in series to the input: voltage-to-current converter (transconductance amplifier), inverting amplifier, summing amplifier, inductive integrator, capacitive differentiator, resistive-capacitive integrator, capacitive-resistive differentiator, inductive-resistive differentiator, etc. The inverting integrators from this list are examples of useful and desired applications of Miller effect in its extreme manifestation.

In all these op-amp inverting circuits with parallel negative feedback, the input current is increased to its maximum. It is determined only by the input voltage and the input impedance according to Ohm's law; it does not depend on the impedance Z.

Negative impedance with voltage inversion is implemented by applying both negative and positive feedback to an op-amp amplifier with a differential input. The input voltage source has to have internal impedance Zint > 0 or it has to be connected through another impedance element to the input. Under these conditions, the input voltage Vi of the circuit changes its polarity as the output voltage exceeds the voltage drop VZ across the impedance (Vi = Vz – Vo < 0). A typical application is a negative impedance converter with voltage inversion (VNIC).[5] It is interesting that the circuit input voltage has the same polarity as the output voltage although it is applied to the inverting op-amp input; the input source has an opposite polarity to both the circuit input and output voltages.

Generalization of Miller arrangement

The original Miller effect is implemented by capacitive impedance connected between the two nodes. Miller theorem generalizes Miller effect as it implies arbitrary impedance Z connected between the nodes. It is supposed also a constant coefficient K; then the expressions above are valid. But modifying properties of Miller theorem exist even when these requirements are violated and this arrangement can be generalized further by dynamizing the impedance and the coefficient.

Non-linear element. Besides impedance, Miller arrangement can modify the IV characteristic of an arbitrary element. The circuit of a diode log converter is an example of a non-linear virtually zeroed resistance where the logarithmic forward IV curve of a diode is transformed to a vertical straight line overlapping the Y axis.

Not constant coefficient. If the coefficient K varies, some exotic virtual elements can be obtained. A gyrator circuit is an example of such a virtual element where the resistance RL is modified so that to mimic inductance, capacitance or inversed resistance.

Dual Miller theorem (for currents)

Definition

There is also a dual version of Miller theorem that is based on Kirchhoff's current law (Miller theorem for currents): if there is a branch in a circuit with impedance Z connecting a node, where two currents I1 and I2 converge to ground, we can replace this branch by two conducting the referred currents, with impedances respectively equal to (1 + α)Z and (1 + α)Z/α, where α = I2/I1. The dual theorem may be proved by replacing the two-port network by its equivalent and by applying the source absorption theorem.[3]

Explanation

Dual Miller theorem actually expresses the fact that connecting a second current source producing proportional current I2 = KI1 in parallel with the main input source and the impedance element changes the current flowing through it, the voltage and accordingly, the circuit impedance seen from the side of the input source. Depending on the direction, I2 acts as a supplemental current source helping or opposing the main current source I1 to create voltage across the impedance. The combination of the actual element and the second current source may be thought as of a new virtual element with dynamically modified impedance.

Implementation

Dual Miller theorem is usually implemented by an arrangement consisting of two voltage sources supplying the grounded impedance Z through floating impedances (see Fig. 3). The combinations of the voltage sources and belonging impedances form the two current sources – the main and the auxiliary one. As in the case of the main Miller theorem, the second voltage is usually produced by a voltage amplifier. Depending on the kind of the amplifier (inverting, non-inverting or differential) and the gain, the circuit input impedance may be virtually increased, infinite, decreased, zero or negative.

Applications

As the main Miller theorem, besides helping circuit analysis process, the dual version is a powerful tool for designing and understanding circuits based on modifying impedance by additional current. Typical applications are some exotic circuits with negative impedance as load cancellers,[6] capacitance neutralizers,[7] Howland current source and its derivative Deboo integrator.[8] In the last example (see Fig. 1 there), the Howland current source consists of an input voltage source VIN, a positive resistor R, a load (the capacitor C acting as impedance Z) and a negative impedance converter INIC (R1 = R2 = R3 = R and the op-amp). The input voltage source and the resistor R constitute an imperfect current source passing current IR through the load (see Fig. 3 in the source). The INIC acts as a second current source passing "helping" current I-R through the load. As a result, the total current flowing through the load is constant and the circuit impedance seen by the input source is increased. As a comparison, in a load canceller, the INIC passes all the required current through the load; the circuit impedance seen from the side of the input source (the load impedance) is almost infinite.

List of specific applications based on Miller theorems

Below is a list of circuit solutions, phenomena and techniques based on the two Miller theorems.

See also

References

  1. ^ Miscellaneous network theorems
  2. ^ a b c EEE 194RF: Miller's theorem
  3. ^ a b Miller's theorem
  4. ^ Working with High Impedance Op Amps AN-241
  5. ^ Nonlinear Circuit Analysis – An Introduction
  6. ^ Negative-resistance load canceller helps drive heavy loads
  7. ^ Impedance and admittance transformations using operational amplifiers by D. H. Sheingold
  8. ^ Consider the "Deboo" Single-Supply Integrator

External links

Further reading

Fundamentals of Microelectronics by Behzad Razavi
Microelectronic Circuits by Adel Sedra and Kenneth Smith
Fundamentals of RF Circuit Design by Jeremy Everard


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Miller-Theorem — Das Millertheorem behandelt die Verlegung von Impedanzen in elektrischen Netzen. Gibt es zwei Netze, die über eine Impedanz Z verbunden sind, so kann diese Impedanz so verlegt werden, dass beide Netze getrennt werden. Die Verlegung in Z1 und Z2… …   Deutsch Wikipedia

  • Miller Theorem — Das Millertheorem behandelt die Verlegung von Impedanzen in elektrischen Netzen. Gibt es zwei Netze, die über eine Impedanz Z verbunden sind, so kann diese Impedanz so verlegt werden, dass beide Netze getrennt werden. Die Verlegung in Z1 und Z2… …   Deutsch Wikipedia

  • Modigliani–Miller theorem — The Modigliani–Miller theorem (of Franco Modigliani, Merton Miller) forms the basis for modern thinking on capital structure. The basic theorem states that, under a certain market price process (the classical random walk), in the absence of taxes …   Wikipedia

  • Modigliani-Miller theorem — The Modigliani Miller theorem (of Franco Modigliani, Merton Miller) forms the basis for modern thinking on capital structure. The basic theorem states that, in the absence of taxes, bankruptcy costs, and asymmetric information, and in an… …   Wikipedia

  • Modigliani-Miller-Theorem — Die Modigliani Miller Theoreme wurden von Franco Modigliani und Merton Miller 1958 in ihrem Aufsatz The Cost of Capital, Corporation Finance and the Theory of Investment vorgestellt. Sie behandeln den Einfluss des Verschuldungsgrades eines… …   Deutsch Wikipedia

  • Modigliani-Miller-Theorem — 1. Begriff: 1958 von ⇡ Modigliani und ⇡ Miller aufgestellte Theoreme über die Zusammenhänge zwischen Marktwert, Kapitalstruktur und Kapitalkosten. Theorem I: Der Gesamtwert eines Unternehmens in einer bestimmten Risikoklasse ist bei gegebenem… …   Lexikon der Economics

  • Modigliani-Miller Theorem - M&M — A financial theory stating that the market value of a firm is determined by its earning power and the risk of its underlying assets, and is independent of the way it chooses to finance its investments or distribute dividends. Remember, a firm can …   Investment dictionary

  • Modigliani-Miller-Theorem — Modigliani Mịller Theorem   [mɔdɪl jɑːni ], von F. Modigliani und M. H. Miller (1958) entwickelter Ansatz der modernen Finanzierungstheorie, wonach auf vollkommenen Kapitalmärkten unter Berücksichtigung des Risikos die Verschuldung eines… …   Universal-Lexikon

  • Miller effect — In electronics, the Miller effect accounts for the increase in the equivalent input capacitance of an inverting voltage amplifier due to amplification of the effect of capacitance between the input and output terminals. The virtually increased… …   Wikipedia

  • Miller, Merton H. — ▪ American economist in full  Merton Howard Miller  born May 16, 1923, Boston, Massachusetts, U.S. died June 3, 2000, Chicago, Illinois       American economist who, with Harry M. Markowitz (Markowitz, Harry M.) and William F. Sharpe (Sharpe,… …   Universalium

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”