Output power of an analog TV transmitter

Output power of an analog TV transmitter

Output power of a TV transmitter is the electric power applied to antenna system. There are two definitions: nominal (or peak) and thermal.

Contents

Power defined in terms of voltage

The average power for a sinusoidal drive is [1]

 P = \frac{1}{T}\int_0^T i(t) \cdot e (t) dt\,\!.

For a system where the voltage and the current are in phase, the output power can be given as

 P = \frac{1}{T \cdot R}\int_0^T e(t)^2 dt\,\!.

In this equation R is the resistance and e(t) is the output voltage

Nominal power of a TV transmitter

Nominal power of a TV transmitter is given as the power during the sync interval. (For the sake of simplicity aural power is omitted) Since, the voltage during the sync interval is a fixed value,

 P_n = \frac{E_p^2}{2\cdot R}\,\!
 P_n = \frac{E^2}{R}\,\!

where E is the rms value of the output voltage.

To measure the nominal output power, measuring devices with time constants much greater than the line time are used. So the measuring equipments measure only the highest level (sync pulse) of a line waveform which is 100 %.

The thermal power

In analogue TV broadcasting, the video signal modulates a carrier by a kind of amplitude modulation (VSB modulation or C3F). The modulation polarity is negative . That means that the higher the level of the video signal the lower the power of the RF signal. The lowest possible modulating signal during the synchrone interval yields 100 % of the carrier. (The nominal power of the transmitter.) The blanking level (300 mV) yields 73 % (in an ideally linear transmitter)[2]. The highest modulating signal at white (1000 mV) yields only 10 % of the carrier. ( so called residual carrier)[3]. So the output power applied to the antenna system is considerably lower than the nominal power. The thermal power which can be measured by a microwave power meter depends on the program content as well as the residual carrier and sync depts.

Ratio of thermal power to nominal power

Since the program content is variable, the thermal power varies during the transmission. However, for testing purposes a standard line waveform can be applied to the transmitter. Usually line waveforms corresponding to 350 mV or 300 mV black image (and without field sync) are applied to the input of the transmitter.

For system B, the duration of the black level 300 mV (together with the front and back porches), is 59.3 μs and it corresponds to 73 % of maximum voltage level.The duration of the sync pulse is 4.7 μs. The total duration of the line is 64 μs.

 P_t = \frac{E^2}{64\cdot R}\cdot (4.7\cdot ( 100  %)^2 + 59.3\cdot ( 73  %)^2) \approx 57 % \cdot \frac{ E^2 }{R}\,\!.

So the maximum thermal power applied to the antenna system is 57 % of the nominal power, even in the black scene. In normal program content this ratio may be around 25 % or less.

References and notes

  1. ^ MIT lecture
  2. ^ Usually the figure 75 % is found to be acceptable.
  3. ^ Sometimes 12.5 % is used as the residual carrier

Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • NTSC — This article is about the television system. For the Indonesian government agency, see National Transportation Safety Committee. Television encoding systems by nation; countries using the NTSC system are shown in green. NTSC, named for the… …   Wikipedia

  • Antenna (radio) — Whip antenna on car …   Wikipedia

  • Low-power broadcasting — Contents 1 United States 1.1 FM radio 1.1.1 LPFM classes 1.1.2 …   Wikipedia

  • Color television — Title card for NBC, promoting their broadcast in RCA color . Color television is part of the history of television, the technology of television and practices associated with television s transmission of moving images in color video. In its most… …   Wikipedia

  • Distortion — This article is about technology, especially electrical engineering. For other uses, see Distortion (disambiguation). Distort redirects here. For other uses, see Distort (disambiguation). A distortion is the alteration of the original shape (or… …   Wikipedia

  • Composite video — Not to be confused with Component video. Composite video On consumer products a yellow RCA connector is typically used for composite video. Type Analog video connector …   Wikipedia

  • Frequency mixer — This article is about non linear mixing operating in the frequency domain. For other types of mixers, see electronic mixer. Frequency Mixer Symbol. In electronics a mixer or frequency mixer is a nonlinear electrical circuit that creates new… …   Wikipedia

  • 405-line television system — The 405 line monochrome analogue television broadcasting system was the first fully electronic television system to be used in regular broadcasting. It was introduced with the BBC Television Service in 1936, suspended for the duration of World… …   Wikipedia

  • SECAM — SECAM, also written SÉCAM (Séquentiel couleur à mémoire,[1] French for Sequential Color with Memory ), is an analog color television system first used in France. A team led by Henri de France working at Compagnie Française de Télévision (later… …   Wikipedia

  • Multichannel television sound — Multichannel television sound, better known as MTS (often still as BTSC, for the Broadcast Television Systems Committee that created it), is the method of encoding three additional channels of audio into an NTSC format audio carrier. Contents 1… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”