Crosshead

Crosshead
Crosshead bearing
Cylindrical trunk guide
Typical steam locomotive with two slide bars

A crosshead[1] is a mechanism used in large reciprocating engines to eliminate sideways pressure on the piston.

Usage

On smaller engines the connecting rod links the piston and the crankshaft directly, but this transmits transverse forces to the piston, since the crankpin (and thus the direction the force is applied) moves from side to side with the rotary motion of the crank. These transverse forces are tolerable in a smaller engine; a larger engine's much greater forces would cause an intolerable degree of wear on the piston and cylinder, as well as increasing overall friction in the engine.

A piston rod is attached to the piston and links it to the crosshead, which is a large casting sliding in crosshead guides (UK: slidebar), allowing it only to move in the same direction as the piston travel. The crosshead also houses the gudgeon pin on which the small end of the connecting rod pivots. In this way, the transverse forces are applied only to the crosshead and its bearings, not to the piston itself.

Internal combustion engines using crossheads make for easier maintenance of the top end of the engine, since the pistons can be easily removed. The piston rod is mounted on the underside of the piston and connected to the crosshead by a single nut in double acting engines.

Large diesel engines (such as those fitted to ships) are of this pattern; the vast majority of steam engines are also built this way.

In the case of the steam engine, a crosshead is essential if the engine is to be double acting - steam is applied to both sides of the piston, which requires a seal around the piston rod.

The same applies to double acting diesel engines (see also: H class battleship (1939): 12 MAN double-acting 2-stroke 9-cylinder diesels).

Crossheads in a steam locomotive can be mounted either to one guide mounted above the crosshead or to two, one above and one below (called an alligator crosshead since it has two "jaws"). The former was preferred in many modern locomotives.

Large diesels often have a plunger oilpump directly attached to the crosshead to supply oil under high pressure to the crosshead bearing.

In many 19th century marine steam engines, the crosshead was a strong metal bar attached to the piston rod and perpendicular to it, which was sometimes used to eliminate transverse forces, as in a steeple engine, and at other times used as a linkage—to side-rods in a side-lever engine or to connecting rods in a square engine.

References


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Crosshead — Cross head ( h?d), n. (Mach.) A beam or bar across the head or end of a rod, etc., or a block attached to it and carrying a knuckle pin; as the solid crosspiece running between parallel slides, which receives motion from the piston of a steam… …   The Collaborative International Dictionary of English

  • crosshead — [krôs′hed΄] n. a sliding bar or block joining a connecting rod and a piston rod: converts reciprocating motion into rotary motion, as in the steam engine …   English World dictionary

  • crosshead — noun Date: 1827 1. a metal block to which one end of a piston rod is secured 2. a heading centered usually between portions of text …   New Collegiate Dictionary

  • crosshead — /kraws hed , kros /, n. 1. Print. a title or heading filling a line or group of lines the full width of the column. 2. Mach. a sliding member of a reciprocating engine for keeping the motion of the joint between a piston rod and a connecting rod… …   Universalium

  • crosshead — noun A metal beam that connects a piston to a connecting rod in an engine …   Wiktionary

  • crosshead — Смотри Траверса …   Энциклопедический словарь по металлургии

  • crosshead — n. sliding metal beam which connects to a piston rod (Machinery); heading of a subsection centered between the body of text v. make the sign of the cross over …   English contemporary dictionary

  • crosshead — cross•head [[t]ˈkrɔsˌhɛd, ˈkrɒs [/t]] n. mac a sliding member of a reciprocating engine for keeping the motion of the joint between a piston rod and a connecting rod in a straight line • Etymology: 1835–45 …   From formal English to slang

  • crosshead — /ˈkrɒshɛd/ (say kroshed) noun 1. Printing a title or heading filling a line or group of lines the full width of the column. 2. the sliding and bearing member of a diesel, steam, or gas engine, between the piston rod and the connecting rod. 3. the …  

  • crosshead — noun 1. a heading of a subsection printed within the body of the text • Syn: ↑crossheading • Hypernyms: ↑heading, ↑header, ↑head 2. metal block that connects to a piston; it slides on parallel guides and moves a connecting rod back and forth • H …   Useful english dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”