- Single-ended triode
single-endedtriode (SET) vacuum tube electronic amplifierthe entire audio signal waveform is amplified by the power triode, in contrast to push-pull amplifiers where two output tubes work together in phase opposition. Small-signal audio and radio frequency amplifiers are single-ended by default, with the exception of balanced amplifier stages. Thus, in practice, the term single-ended triode amplifier applies only to output stages of audio power amplifiers. The phrase directly heated triode single-ended triode amplifier (abbreviated to DHT SET) is used when directly heated triodes are used.
Audio power amplifiers
A typical circuit will have a driver that provides voltage gain, coupled to a triode (like
2A3and 300B), or even pentodes like EL34or the KT88in triodeconfiguration, connected to the loudspeakerthrough an audio transformer in a common cathodearrangement. Audio power triodeis biased to Class A operation by applying negative bias voltageto its input grid(see diagram), or by raising cathode potential with biassing components.
In traditional SET amp, the direct current of output triode (from 30 mA for triode-strapped
6V6to 250 mA for 6C33C) flows continuously through the primary windingof a transformer. This requires inserting gap in transformer core to prevent core saturation by DC current; gapping decreases primary inductanceand limits bass response. In practice, these limitations are handled by increasing transformer size.
An alternative schematic,
parafeed amplifier, solves bandwidth problem by blocking direct current from output transformer (which does not need to be gapped, thus improving its bass response). Power supply is reconfigured into a constant current source, usually with a massive, high-inductance anode choke (gapped inductor), so there is little, if any, gain in cost and weight of magnetic components.
Historically, negative feedback in SET amplifiers was quite common (notably, the Mullard 3-3 design built around
EL84). Today nfb is less popular with SET amplifiers, with many having no global feedback loop. Their frequency response, limited by transformerpassband, is then modulated by irregularities in loudspeaker impedance. This, and the very low attainable power levels (3 Watts for 2A3to 20 Watts for 6C33C), requires careful matching of amplifier to speakers; selection is usually limited to high-efficiency loudspeakers with a sensitivityexceeding 90 dB/ Watt.
Single-ended triode (SET) amplifiers are considered a classic design and have achieved a cult status among certain
audiophiles, because of their excellent midband performance (argued to be the most important part of the audio spectrum in music reproduction) and directness. This high sonic quality is mainly attributed to the simplicity and minimalistic approach of the circuits involved.
Critics of this design point to its electrical inefficiencies in that it consumes the same amount of electricity with no signal as it does when driven to full power. This is true because SET amps are necessarily configured to operate in class A. Push pull designs may be operated in class AB, which idle at lower power levels, at the cost of some distortion as they are driven out of class A into class B operation. Also, there are higher levels of distortion which are canceled out in push-pull designs. Fact|date=May 2008
Estimating power output for a Class A1 amplifier from valve specs
From the available data sheets, obtain the following parametrs, Pa (or P [a+g2] for pentodes) (in watts). Rp in triode (in ohms), and the desired load resistance (Rl) (in ohms) which may vary depending on the design.
Compute maximum theoretical power output by P [ot] = Pa / 2.
Reasoning: In class A, in order to produce a full sine wave, the tube must be exactly half-way on. Therefore the maximum current swing is +/- 50%. No actual amplifier will ever achieve this.
Next, compute P [o] = P [ot] * (1 - Rp/Rl) to obtain an estimate of the maximum obtainable output power.
reasoning: While the valve can be driven all the way to shut-off fairly easily, the maximum current will be limited by the internal resistance of the valve as the grid reaches the voltage of the cathode and is not impeding electron flow. For this reason, valves that have a low Rp can yield more power in class A1 than other valves with similar Pa ratings.
Finally, knock another 10% off to account for the relatively heavy distortion encountered as the valve approaches cut-off.
Class A2 amplifiers can overcome a high Rp by driving the grid positive with respect to the plate. Because this makes the grid a secondary anode, it too will draw current from the cathode while accelerating the remaining electrons towards the plate. Because these grid currents can place extreme demands on the driving circuitry, sometimes requiring as much as 8 watts for larger tubes such as the 211, Class A2 operation is not recommended for Hi-Fi reproduction. A hybrid design called the powerdrive circuit [ [http://www.tubelab.com/powerdrive.htm PowerDrive ] ] can be used to overcome this problem and achieve as much as 45% * Pa total output power.
The grid goes positive with respect to the cathode, to draw grid currant in class AB2, not the plate.
European triode festival
List of vacuum tubes
* [http://www.pmillett.com/ www.pmillett.com] A public domain depository for various audio designs and projects, including tubes and SET.
* [http://www.enjoythemusic.com/magazine/manufacture/0703/ www.enjoythemusic.com] Article titled "Why The SET And Efficient Loudspeaker Approach Works".
Wikimedia Foundation. 2010.
Look at other dictionaries:
Single-ended — is a method by which logic signals are transmitted over a cable.Single ended may also refer to: * Hi Fi amplification where a single triode or pendode is used running in Class A. * Single ended signalling, the simplest method of transmitting… … Wikipedia
European triode festival — Since 2000 each year the European Triode Festival (ETF) has been held in various venues in Europe (the first three events were called Aarhus Triode Festival aka ATF . The ETF focuses on do it yourself audio valve amplifiers using triode vacuum… … Wikipedia
Valve audio amplifier - technical — Circuitry and performance Characteristics of valves Valves are very high input impedance (near infinite in most circuits) and high output impedance devices. They are also high voltage / low current devices.While valves themselves are described… … Wikipedia
Tube sound — (or valve sound) is the characteristic sound associated with a vacuum tube based audio amplifiers. Some audiophiles prefer the sound that is produced by the distortion characteristics of tube based amplifiers. The audible significance of tube… … Wikipedia
Electronic amplifier — A practical amplifier circuit An electronic amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. In… … Wikipedia
Valve amplifier — A valve amplifier or tube amplifier is a type of electronic amplifier that make use of vacuum tubes instead of solid state semiconductor devices (such as transistors). As any other electronic amplifier they serve to increase the power and/or… … Wikipedia
Song Audio — Infobox Company company name = Song Audio Ltd. company company type = Limited Corporation foundation = October 2001 location = Toronto, Ontario, Canada flagicon|Canada key people = Song Kim (founder president) industry = hifi audio equipment… … Wikipedia
Valve RF amplifier — A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical , typically (but not exclusively) radio frequency signals.Low to medium power valve amplifiers for frequencies below… … Wikipedia
Valve audio amplifier — A valve (UK) audio amplifier or vacuum tube (US) audio amplifier is a valve amplifier used for sound recording, reinforcement, or reproduction. Until the invention of solid state devices such as the transistor, all electronic amplification was… … Wikipedia
300B — The 300B is a directly heated power triode using a four pin base, introduced by Western Electric in 1937 to amplify telephone signals. It measures 6.4 inches high and 2.4 inches wide. It has a 40 watt anode dissipation. In the 1980s the 300B was… … Wikipedia