Dock plate


Dock plate

In a loading dock, one problem to overcome is the problem of bridging the gap between a truck and the dock or warehouse floor.[1] Not all trucks are the same height, and the height of the trailer floor within a truck can vary according to how heavily the truck is laden. Thus there is not only a gap to bridge but a height difference to overcome. Various devices are employed in order to achieve this: dock plates, dock levellers, dock boards, and various forms of lift.[2][3] These devices vary in construction, suitability to dock conditions, cost of installation, and loading capacity.[1]

Dock levellers and lifts are generally permanent fixtures at each door of a dock. Dock plates and dock boards are generally, by contrast, portable, and not fixed either to dock or truck.[2]

Dock plates and dock boards are simply metal ramps, bridging the gaps between dock and truck.[4] Dock plates are generally made out of aluminium whilst dock boards are generally made out of steel. Aluminium dock plates are thus more suitable for lighter loads, such as handcarts and dollies, whereas steel dock boards are more suitable for heavier motorized equipment such as fork lift trucks and electric pallet trucks. Another difference between dock plates and dock boards, in addition to their load-bearing capabilities, is their construction. Dock plates are simple flat plates, whereas dock boards have curbs, bolted or welded to the edge of the board.[5] Run-off is prevented by a simple painted yellow strip along the edge of a dock plate, whereas it is the curbs (also generally painted yellow) that prevent run-off on dock boards.[3] Run-off is thus a significant risk on dock plates, since the yellow strip is not a particularly effective mechanism for preventing it.[1]

Both dock plates and dock boards have a diamond pattern embossed onto their upper surfaces, to prevent wheel slip as carts and vehicles travel up and down the incline. Similarly, they both have locking T-bar legs that extend down into the gap between truck and dock, to secure them. They are both portable. But dock boards are heavier than dock plates. The latter may be carried by hand, and are generally fitted with handles for doing so. The former usually require a fork lift in order to place and remove them, and are generally fitted with either loops or chains, used for attaching the dock board to the forks of the fork lift.[3][1]

This loading dock has a dock leveller below the door. In this picture it is in the stowed position.

Dock levellers are, as mentioned, fixed to the dock. They comprise a simple metal plate, called a lip, that is raised from a stowed position and then lowered onto the back of the truck. They are operated either manually, via a simple pull chain, or hydraulically, with an electric pump driving a piston to lift the plate.[4][3][6]

Dock levellers are more expensive devices than the comparatively light-weight dock plates and dock boards. The most common form of dock leveller is the recessed, or pit, dock leveller. As the name suggests, this type of leveller is contained in a recess, or pit, beneath the dock door and floor surface. Dock levellers are stronger than dock plates and dock boards, making them suitable not only for motorized fork lift trucks but also for master conveyors (for which neither dock plates or dock boards are suitable).[3]

Because they carry heavy motorized equipment, the grade of the incline has to be shallow. The greater the height differential between truck and dock that a dock leveller can compensate for, the longer the leveller itself has to be. Moreover, the grade of the incline must not be so great that the vehicles cannot climb it. A height differential of between 7 and 8 inches generally requires a 6-foot-long (1.8 m) leveller for an electric palette carrier. A height differential of between 17 and 18 inches generally requires a 12-foot-long (3.7 m) leveller for a petrol-engined fork lift truck.[1]

Dock levellers (and indeed dock plates and dock boards) are used where a building has a truck-level door, i.e. a door with a floor level roughly at the same height as the floor of the truck's trailer. Some buildings only have drive-in doors, i.e. doors at the same level as the ground outside of the building, suitable for driving directly into the building.[6]

For loading docks with drive-in doors, and also (albeit rarely) for loading docks with truck-level doors, a lift is sometimes employed.[6]

Other, less common, devices employed when bridging the gap between truck and dock are truck levellers. These are hydraulic lifts positioned beneath the rear wheels of the truck, that are used to raise and lower the truck so that it is level with the loading dock edge. The problems with truck levellers, that make them rarely employed, are twofold. First: They cause the truck interior to be at an incline, which causes loading and unloading difficulties. Second: They are expensive to maintain, since they require (being below ground level and open to the air) proper drainage and protection against the weather.[2]

Recessed dock levellers also have problems of exposure to the weather. However, because they are recessed into the dock, which is above ground level, they do not have as great a problem with drainage. Equally, because they are recessed into the dock, they extend partially back from the dock edge. A dock leveller can be installed so that it extends inside the loading dock door, and thus inside the building, protecting it from the weather.[7]

Major manufacturers & Distributors

  1. Dynamic Loading http://www.dynamicloading.com
  2. Butt http://www.butt.de
  3. Rite Hite Ramps http://www.ritehite.com
  4. Beacon Technology http://www.beacontechnology.com

References

  1. ^ a b c d e David E. Mulcahy (1994). "How to bridge the gap between dock edge and trailer bed". Warehouse distribution and operations handbook. McGraw-Hill Handbooks Series. McGraw-Hill Professional. pp. 4.28–4.41. ISBN 0070440026. 
  2. ^ a b c Ernst F. Bolten (1997). Managing time and space in the modern warehouse: with ready-to-use forms, checklist & documentation. AMACOM Div American Mgmt Assn. pp. 49–50. ISBN 0814479561. 
  3. ^ a b c d e David E. Mulcahy (2007). Eaches or pieces order fulfillment, design, and operations handbook. Series on resource management. CRC Press. pp. 83–87. ISBN 0849335221. 
  4. ^ a b Philip Obal (2006). Glossary of Supply Chain Terminology: A Dictionary on Technology, Logistics, Transportation, Warehousing, Manufacturing, Purchasing, and More! (4th ed.). Industrial Data & Information Inc.. pp. 167. ISBN 0966934539. 
  5. ^ Steven Di Pilla (2009). Slip, Trip, and Fall Prevention: A Practical Handbook (2nd ed.). CRC Press. pp. 373–374. ISBN 1420082345. 
  6. ^ a b c Pierre Boiron and Claude Boiron (2008). Commercial Real Estate Investing in Canada: The Complete Reference for Real Estate Professionals. John Wiley and Sons. pp. 346. ISBN 047083840X. 
  7. ^ Barry Lord (1999). The manual of museum planning. Professional museum and heritage series (2nd ed.). Rowman Altamira. pp. 211. ISBN 0742504069. 

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Dock Ellis — 200px Pitcher Born: March 11, 1945(1945 03 11) Los Angeles, California Died: December 19, 2008(2008 12 19) (a …   Wikipedia

  • Dock Museum — Coordinates: 54°06′44″N 3°14′24″W / 54.1121°N 3.2400°W / 54.1121; 3.2400 …   Wikipedia

  • Mort's Dock — Workers at Mort s Dock lay the keel plate for a new vessel shortly after HMAS Deloraine was launched in 1941. Mort s Dock is a former dry dock, slipway, and shipyard in Balmain, New South Wales, Australia. It was the first dry dock in Australia …   Wikipedia

  • Dry dock — Dry Dry (dr[imac]), a. [Compar. {Drier}; superl. {Driest}.] [OE. dru[yogh]e, druye, drie, AS. dryge; akin to LG. dr[ o]ge, D. droog, OHG. trucchan, G. trocken, Icel. draugr a dry log. Cf. {Drought}, {Drouth}, 3d {Drug}.] 1. Free from moisture;… …   The Collaborative International Dictionary of English

  • Dry plate — Dry Dry (dr[imac]), a. [Compar. {Drier}; superl. {Driest}.] [OE. dru[yogh]e, druye, drie, AS. dryge; akin to LG. dr[ o]ge, D. droog, OHG. trucchan, G. trocken, Icel. draugr a dry log. Cf. {Drought}, {Drouth}, 3d {Drug}.] 1. Free from moisture;… …   The Collaborative International Dictionary of English

  • Dry-plate process — Dry Dry (dr[imac]), a. [Compar. {Drier}; superl. {Driest}.] [OE. dru[yogh]e, druye, drie, AS. dryge; akin to LG. dr[ o]ge, D. droog, OHG. trucchan, G. trocken, Icel. draugr a dry log. Cf. {Drought}, {Drouth}, 3d {Drug}.] 1. Free from moisture;… …   The Collaborative International Dictionary of English

  • North Dock, Llanelli — North Dock is a former industrial dock in Llanelli, West Wales used mainly for exporting coal and tin plate from South Wales. It is also the name of the area immediately surrounding the dock. Llanelli Beach is also known locally as North Dock.… …   Wikipedia

  • Screw dock — Screw Screw (skr[udd]), n. [OE. scrue, OF. escroue, escroe, female screw, F. [ e]crou, L. scrobis a ditch, trench, in LL., the hole made by swine in rooting; cf. D. schroef a screw, G. schraube, Icel. skr[=u]fa.] 1. A cylinder, or a cylindrical… …   The Collaborative International Dictionary of English

  • Screw plate — Screw Screw (skr[udd]), n. [OE. scrue, OF. escroue, escroe, female screw, F. [ e]crou, L. scrobis a ditch, trench, in LL., the hole made by swine in rooting; cf. D. schroef a screw, G. schraube, Icel. skr[=u]fa.] 1. A cylinder, or a cylindrical… …   The Collaborative International Dictionary of English

  • Bridge the gap — is an idiom that means to make a connection (bridge) where there is a great difference (gap). Bridge the Gap may also refer to:Music * Bridging the Gap 2000 album by Black Eyed Peas * Bridging the Gap 2000 album by Charlie Wilson * Bridging the… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.