Ethernet Powerlink

Ethernet Powerlink

Ethernet POWERLINK is a deterministic real-time protocol for standard Ethernet. It is an open protocol managed by the Ethernet POWERLINK Standardization Group (EPSG). It was introduced by Austrian automation company B&R in 2001.

This protocol has nothing to do with power distribution via Ethernet cabling or power over Ethernet (PoE), power line communication or Bang & Olufsens PowerLink cable.

Overview

Ethernet POWERLINK was created taking care of standard-compliance. It expands Ethernet with a mixed Polling- and Timeslicing mechanism. That brings:

* guaranteed transfer of time-critical data in very short isochronic cycles with configurable response time
* time-synchronisation of all nodes in the network with very high precision of sub-microseconds
* transmission of less timecritical data in a reserved asynchronous channel

Modern implementations reach cycle-times of under 200 µs and a time-precision (jitter) of less than 1 µs.

tandardization

POWERLINK is standardized by the opened user- and producer-group EPSG (Ethernet POWERLINK Standardization Group) as a public standard.EPSG has been founded in June 2003 as an independent association. Its focus is to leverage theadvantages of Ethernet for high performance Real-Time networkingsystems based on the Ethernet POWERLINK Real-Time protocol, introduced by B&R end of 2001.Various working groups are focusing on different tasks like safety, technology, marketing, certification and end users. The EPSG is cooperating with leading standardization bodies and associations, like the CAN in Automation (CiA) Group and the IEC.

Physical layer

The original physical layer specified was 100Base-X Fast Ethernet (IEEE 802.3). Since end of 2006 ETHERNET Powerlink with Gigabit Ethernet supporting a transmission rate ten times higher (1,000 Mbit/s) is in use. That offers a better performance for the future to extended systems withmajor production performance, a series of module control systems, numerous drives and completely integrated security equipment. Gigabit Ethernet­ is on the threshold of general dissemination in IT systems. There is no need for major change in system designs, components or cabling. Networked units that master this high transmission rate and a somewhat better cable (Cat6) must be used. The transition to higher speed Ethernet variants is always possible since ETHERNET Powerlink is also attached as a standard Ethernet design and can launch its applications with standard modules such as microcomputers and FPGA modules.Usage of repeating hubs instead of switches within the Real-time domain is recommended to minimise delay and jitter. ETHERNET Powerlink uses IAONA's Industrial Ethernet Planning and Installation Guide for clean cabling of industrial networks and both industrial Ethernet connectors 8P8C (RJ45) and M1 are accepted.

Data Link Layer

The Standard Ethernet Data Link Layer of ETHERNET Powerlink is extended by an additional bus scheduling mechanism which secures that at a time only one node is accessing the network. The schedule is divided into an isochronous phase and an asynchronous phase. During the isochronous phase, time-critical data is transferred, while the asynchronous phase provides bandwidth for the transmission of non time-critical data. The Managing Node (MN) grants access to the physical medium via dedicated poll request messages. As a result, only one single node (CN) has access to the network at a time, which avoids collisions, usually present on Standard Ethernet. The CSMA/CD mechanism of standard Ethernet, which causes non-deterministic Ethernet behaviour, is deactivated by the collision avoidance mechanism of the ETHERNET Powerlink scheduling mechanism.

Basic Cycle

After system start-up is finished, the Real-Time domain is operating under Real-Time conditions. The scheduling of the basic cycle is controlled by the Managing Node (MN). The overall cycle time depends on the amount of isochronous data, asynchronous data and the number of nodes to be polled during each cycle.

The basic cycle consists of the following phases:

* Start Phase: The Managing Node is sending out a synchronization message to all nodes. The frame is called SoC - Start of Cycle.
* Isochronous Phase: The Managing Node calls each node to transfer time-critical data for process or motion control by sending the Preq - Poll Request - frame. The addressed node answers with the Pres - Poll Response - frame. Since all other nodes are listening to all data during this phase, the communication system provides a producer-consumer relationship.The time frame which includes Preq-n and Pres-n is called time slot for the addressed node.
* Asynchronous Phase: The Managing Node grants the right to one particular node for sending ad-hoc data by sending out the SoA - Start of Asynchronous - frame. The addressed node will answer with ASnd. Standard IP-based protocols and addressing can be used during this phase.

The quality of the Real-Time behaviour depends on the precision of the overall basic cycle time. The length of individual phases can vary as long as the total of all phases remain within the basic cycle time boundaries. Adherence to the basic cycle time is monitored by the Managing Node. The duration of the isochronous and the asynchronous phase can be configured.

Picture 1: Frames above the time line are sent by the MN, below the time line by different CNs.

Picture 2: Time slots for nodes and the asynchronous time slot

Multiplex for Bandwidth Optimization

In addition to transferring isochronous data during each basic cycle, some nodes are also able to share transfer slots for better bandwidth utilization. For that reason, the isochronous phase can distinguish between transfer slots dedicated to particular nodes, which have to send their data in every basic cycle, and slots shared by nodes to transfer their data one after the other in different cycles. Therefore less important yet still time-critical data can be transferred in longer cycles than the basic cycle. Assigning the slots during each cycle is at the discretion of the Managing Node.

Picture 3: Time slots in EPL multiplexed mode.

ETHERNET Powerlink Safety

Today, machines, plants and safety systems are stuck in a rigid scheme made up of hardware-based safety functions. The consequences of this are cost-intensive cabling and limited diagnostic options. The solution is the integration of safety relevant application data into the standard serial control protocol. ETHERNET Powerlink Safety (EPLsafety). EPLsafety allows both publish/subscriber and client/server communication. Safety relevant data is transmitted via an embedded data frame inside of standard communication messages. Measures to avoid any undetected failures due to systematic or stochastic errors are an integral part of the safety protocol. EPLsafety is in conformance with IEC 61508. The protocol fulfils the requirements of SIL 3. Error detection techniques have no impact on existing transport layers.

External links

* [http://www.ethernet-powerlink.org/ Ethernet POWERLINK Standardization Group website]
*http://sourceforge.net/projects/openpowerlink Open Source Stack for LINUX


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Ethernet-Powerlink — (Offizielle Schreibweise: Ethernet POWERLINK) ist eine Protokollerweiterung zum Ethernet Standard nach IEEE 802.3, um Echtzeitdaten im Mikrosekundenbereich zu übertragen. Der Hauptanwendungszweck ist die Übertragung von Prozessdaten in der… …   Deutsch Wikipedia

  • Ethernet Powerlink — (Offizielle Schreibweise: Ethernet POWERLINK) ist eine Protokollerweiterung zum Ethernet Standard nach IEEE 802.3, um Echtzeitdaten im Mikrosekundenbereich zu übertragen. Der Hauptanwendungszweck ist die Übertragung von Prozessdaten in der… …   Deutsch Wikipedia

  • Ethernet POWERLINK — Saltar a navegación, búsqueda Ethernet POWERLINK (conocido también con el acrónimo EPL) es un protocolo de comunicación en tiempo real basado en hardware estándar Ethernet. Su principio de funcionamiento hace que el POWERLINK sea apto para… …   Wikipedia Español

  • Ethernet Powerlink — est un protocole temps réel et déterministe pour Ethernet standard. Ce protocole ouvert et exempt de licence est régi par l Ethernet Powerlink Standardization Group (EPSG). Il a été introduit pour la première fois sur le marché par la société B R …   Wikipédia en Français

  • Ethernet powerlink — является детерминированным в режиме реального времени протоколом для стандартного Ethernet. Это открытый управляемый протокол Ethernet POWERLINK Standardization Group (EPSG). Он был введен австрийской автоматизационной компанией B R в 2001 году.… …   Википедия

  • Powerlink — Ethernet Powerlink Ethernet Powerlink est un protocole temps réel et déterministe pour Ethernet standard. Ce protocole ouvert et exempt de licence est régi par l Ethernet Powerlink Standardization Group (EPSG). Il a été introduit pour la première …   Wikipédia en Français

  • POWERLINK — est un protocole temps réel et déterministe pour Ethernet standard. Ce protocole ouvert et exempt de licence est régi par l Ethernet Powerlink Standardization Group (EPSG). Il a été introduit pour la première fois sur le marché par la société B R …   Wikipédia en Français

  • Ethernet — im TCP/IP‑Protokollstapel: Anwendung HTTP IMAP SMTP DNS … Transport TCP UDP Internet …   Deutsch Wikipedia

  • Ethernet — Saltar a navegación, búsqueda Tarjeta de Red ISA de 10 Mbps …   Wikipedia Español

  • Industrial Ethernet — Иное название этого понятия  «IE»; см. также другие значения. Siemens ESM TP80 (6GK1105 3AB10) 8 портовый (RJ45) концентратор для технологии Industrial Ethernet …   Википедия

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”