Regenerative brake

Regenerative brake

A regenerative brake is a mechanism that reduces vehicle speed by converting some of its kinetic energy into another useful form of energy. This captured energy is then stored for future use or fed back into a power system for use by other vehicles.

For example, electrical regenerative brakes in electric railway vehicles feed the generated electricity back into the supply system. In battery electric and hybrid electric vehicles, the energy is stored in a battery or bank of capacitors for later use. Other forms of energy storage which may be used include compressed air and flywheels.

Regenerative braking should not be confused with "dynamic braking", which dissipates the electrical energy as heat.

Limitations

Traditional friction-based braking is still used with electrical regenerative braking for the following reasons:
* The regenerative braking effect rapidly reduces at lower speeds, therefore the friction brake is still required in order to bring the vehicle to a complete halt.
* The friction brake is a necessary back-up in the event of failure of the regenerative brake.
* Most road vehicles with regenerative braking only have power on some wheels (as in a 2WD car) and regenerative braking power only applies to such wheels, so in order to provide controlled braking under difficult conditions (such as in wet roads) friction based braking is necessary on the other wheels.
* The amount of electrical energy capable of dissipation is limited by either the capacity of the supply system to absorb this energy or on the state of charge of the battery or capacitors. No regenerative braking effect can occur if another electrical component on the same supply system is not currently drawing power or if the battery or capacitors are already charged. For this reason, it is normal to also incorporate dynamic braking to absorb the excess energy.For these reasons there is typically the need to control the regenerative braking and match the friction and regenerative braking to produce the desired total braking output. The GM EV-1 was the first commercial car to do this. Engineers Abraham Farag and Loren Majersik were issued 2 patents for this 'Brake by Wire' technology. [GM patent [http://www.google.com/patents?id=VzshAAAAEBAJ&dq=5775467 5775467] – "Floating electromagnetic brake system".] [GM patent [http://www.google.com/patents?id=_A0kAAAAEBAJ&dq=5603217 5603217] – "Compliant master cylinder".]

The motor as a Generator

Regenerative braking utilizes the fact that an electric motor can also act as a generator. The vehicle's electric traction motor is operated as a generator during braking and its output is supplied to an electrical load. It is the transfer of energy to the load which provides the braking effect.

An early example of this system was the Energy Regeneration Brake, developed in 1967 for the Amitron. This was a completely battery powered urban concept car whose batteries were recharged by regenerative braking, thus increasing the range of the automobile. [ Time Magazine, Business Section, "Next: the Voltswagon?", December 22, 1967. ]

Electric railway vehicle operation

During braking, the traction motor connections are altered to turn them into electrical generators. The motor fields are connected across the main traction generator (MG) and the motor armatures are connected across the load. The MG now excites the motor fields. The rolling locomotive or multiple unit wheels turn the motor armatures, and the motors act as generators, either sending the generated current through onboard resistors (dynamic braking) or back into the supply (regenerative braking)
For a given direction of travel, current flow through the motor armatures during braking will be opposite to that during motoring. Therefore, the motor exerts torque in a direction that is opposite from the rolling direction.

Braking effort is proportional to the product of the magnetic strength of the field windings, times that of the armature windings.

Savings of 17% are claimed for Virgin Trains Pendolinos. [cite news | title=Regenerative braking boosts green credentials | url =http://www.railwaygazette.com/features_view/article/2007/07/7577/regenerative_braking_boosts_green_credentials.html | work =Railway Gazette International | date = July 2, 2007 |accessdate=2008-03-21 | author=Roger Ford] There is also less wear on friction braking components.

Comparison of dynamic and regenerative brakes

Dynamic brakes ("rheostatic brakes" in the UK), unlike regenerative brakes, dissipate the electric energy as heat by passing the current through large banks of variable resistors. Vehicles that use dynamic brakes include forklifts, Diesel-electric locomotives and streetcars. If designed appropriately, this heat can be used to warm the vehicle interior. If dissipated externally, large radiator-like cowls are employed to house the resistor banks.

The main disadvantage of regenerative brakes when compared with dynamic brakes is the need to closely match the generated current with the supply characteristics. With DC supplies, this requires that the voltage be closely controlled. Only with the development of power electronics has this been possible with AC supplies, where the supply frequency must also be matched (this mainly applies to locomotives where an AC supply is rectified for DC motors).

A small number of mountain railways have used 3-phase power supplies and 3-phase induction motors. This results in a near constant speed for all trains as the motors rotate with the supply frequency both when motoring and braking.

Use in motor sport

Max Mosley of the FIA has announced that all cars Fact|date=August 2008 will become hybrid by 2013, along with other changes to the vehicles. The governing body of international motor sport, the FIA, has allowed the use of 60 kW "Kinetic Energy Recovery Systems" (KERS), in the regulations for the 2009 Formula One season. [cite web | url =http://www.fia.com/resources/documents/1151088479__2009_F1_TECHNICAL_REGULATIONS.pdf |format=PDF | title =2009 Formula One Technical Regulations | publisher =FIA | date =December 22, 2006 | accessdate =2006-12-22 | language = ] [cite web |url=http://www.evworld.com/syndicated/evworld_article_1160.cfm |publisher=EVWorld |author=Chris Ellis |title=Formula One: 'Braking' New Ground |date=December 26, 2006 |accessdate=2008-03-21] BMW and Honda are testing it. [http://www.carmondo.de/blog/2008/07/03/honda-und-bmw-mit-formel-1-hybriden/ de]

The hybrid system that will be implemented in Formula 1 is known as KERS, which stands for Kinetic Energy Recovery System. The maximum power that can be released from such a system is restricted to 60 kW by the FIA. Energy can either be stored as mechanical energy (as in a flywheel) or can be stored as electrical energy (as in a battery or supercapacitor). [cite web |url=http://www.fia.com/resources/documents/1151088479__2009_F1_TECHNICAL_REGULATIONS.pdf|title=2009 FORMULA ONE TECHNICAL REGULATIONS|publisher=FIA| author= FIA management |date=December 22, 2006 |accessdate=2008-07-08]

The first of these systems to be revealed was the Flybrid [http://www.racecar-engineering.com/articles/f1/182017/f1-kers-flybrid.html] which appeared in an article in Racecar Engineering magazine.

The Flybrid F1 KERS System weighs 24 kg and has an energy capacity of 400 kJ after allowing for internal losses. A maximum power boost of 60 kW (81.6 PS) for 6.67 sec is available. The 20-cm diameter flywheel weighs 5.0 kg and revolves at up to 64,500 rpm. Maximum torque is 18 Nm. The system occupies a volume of 13 liters.

Two minor incidents involved testing the KERS system in F1|2008 have been reported. The first occurred when the Red Bull Racing team tested their KERS battery for the first time in July, it malfunctioned and caused a fire scare, resulting in the team's factory being evacuated. [cite news| title =KERS failure caused Red Bull fire scare | publisher =autosport.com| url =http://www.autosport.com/news/report.php/id/69199| date =2008-07-17| accessdate =2008-07-22] The second was less than a week later when a BMW Sauber mechanic was given an electric shock when he touched Christian Klien's KERS-equipped car during a test at the Jerez circuit. [cite news| title =BMW mechanic escapes KERS scare | publisher =autosport.com| url =http://www.autosport.com/news/report.php/id/69391| date =2008-07-22| accessdate =2008-07-22] Mclaren have recently begun testing of their KERS system at the Jerez test track in preparation for the 2009 F1 season, although it is not yet known if they will be operating an electrical or mechanical system. [ [http://www.racecar-engineering.com/news/people/274178/mclaren-on-track-with-kers.html] ]

Automobile Club de l'Ouest, the organizer behind the annual 24 Hours of Le Mans event and the Le Mans Series is currently "studying specific rules for LMP1 which will be equipped with a kinetic energy recovery system." [cite web | url =http://www.lemans.org/sport/sport/reglements/ressources/auto_2008/cdc_reglement_lmp_fr_gb_2008.pdf |format=PDF |title =ACO Technical Regulations 2008 for Prototype "LM"P1 and "LM"P2 classes, page 3| publisher =Automobile Club de l'Ouest (ACO) | date =2007-12-20 | accessdate =2008-01-20 ] Peugeot being the first manufacturer to unveil a fully functioning LMP-1 car in the form of the 908 HY at the 2008 Autosport 1000km race at Silverstone. [http://www.racecar-engineering.com/news/people/273697/peugeot-reveal-hybrid-racer-for-2009.html]

Toyota has used a supercapacitor for regeneration on Supra HV-R hybrid race car that won the 24 Hours of Tokachi race in July 2007. [ [http://www.greencarcongress.com/2007/07/toyota-hybrid-r.html Green Car Congress: Toyota Hybrid Race Car Wins Tokachi 24-Hour Race; In-Wheel Motors and Supercapacitors ] ]

Use in compressed air cars

Regenerative brakes are being used in compressed air cars to refuel the tank during braking.

See also

* Brake (railway)
* Electromagnetic brake
* Dynamic braking
* Regenerative shock absorber
* Supercapacitor

References


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Regenerative shock absorber — A regenerative shock absorber is a type of shock absorber that converts parasitic intermittent linear motion and vibration into useful energy, such as electricity. Conventional shock absorbers simply dissipate this energy as heat. When used in an …   Wikipedia

  • Brake — A brake is a device for slowing or stopping the motion of a machine or vehicle, or alternatively a device to restrain it from starting to move again. The kinetic energy lost by the moving part is usually translated to heat by friction.… …   Wikipedia

  • Drum brake — A drum brake with the drum removed as used on the rear wheel of a car or truck. Note that in this installation, a cable operated parking brake uses the service shoes …   Wikipedia

  • Railway brake — A traditional clasp brake: the brake shoe (brown) bears on the surface (tyre) of the wheel (red), and is operated by the levers (grey) on the left …   Wikipedia

  • Disc brake — Close up of a disc brake on a car On automobiles, disc brakes are often located with …   Wikipedia

  • Railway air brake — Piping diagram from 1920 of a Westinghouse E T Air Brake system on a locomotive …   Wikipedia

  • Emergency brake (train) — This article is about emergency brakes on trains. For emergency brakes in cars, see hand brake. Driver s brake handle in a UK Electric Multiple Unit On trains, the expression emergency brake has several meanings: The maximum brake force available …   Wikipedia

  • New York Air Brake — NYAB redirects here. For other uses, see NYAB (disambiguation). New York Air Brake Type Privately Held Company Founded 1890 Headquarters Watertown, New York USA …   Wikipedia

  • Energy Regeneration Brake — The Energy Regeneration Brake was the name for a system designed to automatically switch an electric motor into a generator as the vehicle slowed. Braking energy is captured so that batteries can be recharged, thus increasing the range of the… …   Wikipedia

  • Countersteam brake — A countersteam brake is a brake on a steam locomotive that uses the engine (specifically the cylinders) to help brake the locomotive. It uses the working principle of steam cylinders fitted with slide or piston valves such that, by changing the… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”