Digital Control Bus

DCB (Digital Control Bus, Digital Connection Bus^[1] or Digital Communication Bus^[2][3] in some sources) was a proprietary data interchange interface by Roland Corporation, developed in 1981^[3] and introduced in 1982 in their Roland Juno-60 and Roland Jupiter-8 products^[3]. DCB functions were basically the same as MIDI, but unlike MIDI (which is capable of transmitting a wide array of information), DCB could provide note on/off and program change only. Data was relayed using a thick cable that connected to a port vaguely resembling a parallel port. DCB-to-MIDI adapters were produced for a number of early Roland products. The DCB interface was made in 2 variants, earlier one used 14-pin sockets and cables, later switching to standard DIN 5-pin plugs — connectors that became MIDI standard^[3].

Supporting equipment

DCB was quickly replaced by MIDI in the early 1980s. The only DCB-equipped instruments produced were the Roland Jupiter-8 and Juno-60^[2]; Roland produced at least two DCB sequencers, the JSQ-60 and the MSQ-700. The latter was capable of saving eight sequences, or a total of 3000 notes, and was capable of transmitting and receiving data via MIDI (though it could not convert signals between DCB and MIDI, nor could it use both protocols simultaneously). Roland later released the MD-8, a rather large black box capable of converting MIDI signals to DCB and vice versa. While this allows note on/off to be sent to a Juno-60 by MIDI, the solution pales in comparison to the full MIDI implementation on the Juno-60's successor, the Roland Juno-106. A few companies offer similar conversion boxes to connect DCB instruments to regular MIDI systems for support of vintage synths in modern sound production environments.

Implementation

Following information comes from the Roland Juno 60 Service Notes, First Edition, page 17-19.

Physical connection

DCB uses a special 14-wire connection. The first 7 consist of 3 wires in each direction plus a shared ground. The signals are standard TTL 0-5V, except the Rx Busy output, which is an open collector pulldown.

1. Rx Busy 2. Rx Data 3. Rx Clock 4. Ground 5. Tx Busy 6. Tx Data 7. Tx Clock

The remaining 7 wires may be used for special purposes.

8. Unreg 9. VCA Lower 10. VCA Upper 11. VCF Lower 12. VCF upper 13. VCO-2 14. VCO-1

These are not used in the Juno 60.

Pinout

View from rear panel. Amphenol DDK connector.

7  6  5  4  3  2  1 

14 13 12 11 10 9 8

Serial data

The DCB is a standard asynchronous serial stream (using an 8251A IC in the Juno 60), LSB first, 8 data bits, 2 stop bits, odd parity, and a Baud rate of 31.25kHz.

Message (Block) Structure)

DCB data is sent in short blocks messages consisting of an identifier, one or more data codes, and an end mark. Blocks may be sent intermittently (JP-8, OP-8) or continuously (Juno 60), in which case end marks are not used.

Identifier/start	Data	Data	...	End
F1-FE	0-F0	0-F0	...	FF

Identifier is 1 byte using a value F1 through FE, which acts as both a start marker and a message type. Data which follows must not use these data bytes. In practice only FD (patch code) and FE (key code) are used.

Data codes are one or more sections or channels, each one byte. The number of bytes or channels depends on the transmitter's configuration, but doesn't change once communication has been started. All data values must be in the range 00-F0.

The end mark is an FF character. It is omitted if the message has a predefined length or the next message starts immediately after the data.

FD: Patch Code Block

This message identifies a patch, by a single byte. Juno 60 ignores this. It is sent once after a patch change, with the first key code by OP-8 and JP-8. It does not have an end mark.

FE: Key Code

This message identifies a key event. It contains one byte for each note channel the transmitter supports - so it is 8 bytes long for JP-8 and OP-8, or 6 bytes for Juno 60. Each channel byte defines a key number (bits 0-6) and whether the key is gated on (1) or off (bit 7). Keys are identified with 0-96 with zero meaning C0 (16.4Hz), up to 96 C8 (4205Hz). Channels are assigned in the order defined by the transmitter's key assign mode. For OP-8, this is Ch1 - Ch8. For JP-8 split mode, Upper 4 keys followed by Lower 4 keys. JP-8 dual mode, the data for the first 4 channels is duplicated to the second 4.

If the Juno-60 receives more channels than it physically has voices, the extra channels are "queued" and played later when possible. Whereas the JP-8 only acccepts 8 channels.

References

1. ^ Jenkins, Mark (2007). Analog Synthesizers: Understanding, Performing, Buying. Amsterdam; Boston; London: Elsevier/Focal Press. p. 91. ISBN 0240520726. 
2. ^ ^{a b} Russ, Martin (1996). Sound Synthesis and Sampling. Focal Press. p. 193. ISBN 9780240514291. 
3. ^ ^{a b c d} Kakehashi, Ikutarō; Olsen, Rober (2002). I Believe in Music: Life Experiences and Thoughts on the Future of Electronic Music by the Founder of the Roland Corporation. Hal Leonard Corporation. p. 197. ISBN 9780634037832. 

This sound technology article is a stub. You can help Wikipedia by expanding it.v · Categories: Electronic musical instruments Computer buses Sound technology stubs Wikimedia Foundation. 2010. Игры ⚽ Нужно сделать НИР? Stagecoach South East Maryland Route 313 Look at other dictionaries: Digital Control Bus — (parfois Digital Connection Bus[1] ou Digital Communication Bus[2]) est un type d interface utilisé sur certains instruments de musique électronique. C est une interface propriétaire développée par la société Roland Corporation en 1981[3]. Elle… …   Wikipédia en Français Direct digital control — (DDC) is the automated control of a condition or process by a digital device (computer).[1][2] A very early example of a DDC system meeting the above requirements was completed by the Australian business Midac in 1981 1982 using R Tec Australian… …   Wikipedia Direct Digital Control — (DDC) refers to the ability to control HVAC (Heating, Ventilating, and Air Conditioning) devices via microprocessors containing a software performing the control logic. DDC receive analog and digital inputs from the sensors and devices installed… …   Wikipedia Digital signage — Digital sign video clip, Dearborn, MI Digital signage as flight information display system at the Taiwan Taoyuan International Airport. Digital signage is …   Wikipedia Digital Signal Interface — (DSI) is a protocol for the controlling of lighting in buildings (initially electrical ballasts). It was created in 1991 by Austrian company Tridonic and is based on Manchester coded 8 bit protocol, data rate of 1200 baud, 1 start bit, 8 data… …   Wikipedia Digital model railway control systems — A number of control systems are available to operate locomotives on model railways. The earlier traditional analog systems where the speed and the direction of a train is controlled by adjusting the voltage on the track are still popular while… …   Wikipedia Bus (computing) — 4 PCI Express bus card slots (from top to bottom: x4, x16, x1 and x16), compared to a 32 bit conventional PCI bus card slot (very bottom) In computer architecture, a bus is a subsystem that transfers data between components inside a computer, or… …   Wikipedia Digital Living Network Alliance — Founded June 2003 (2003 06)[1] Headquarters 4000 Kruse Way Place, Bldg 2, Ste 250 La …   Wikipedia Digital Addressable Lighting Interface — (DALI) is a technical standard for network based systems that control lighting in buildings. It was established as a successor for 0 10 V lighting control systems, and as an open standard alternative to Digital Signal Interface (DSI), on… …   Wikipedia Digital security — gives individuals the freedom to embrace the digital lifestyle – to confidently engage in everyday interactions across all digital devices. Digital security affects all aspects of the digital lifestyle, which, among others, comprises computers… …   Wikipedia 18+ © Academic, 2000-2024 Contact us: Technical Support, Advertising Dictionaries export, created on PHP, Joomla, Drupal, WordPress, MODx. Mark and share Search through all dictionaries Translate… Search Internet Share the article and excerpts Direct link … Do a right-click on the link above and select “Copy Link”