Head gasket

Head gasket
Different kinds of gaskets, #4 indicating a V4 or boxer engine head gasket.
A replacement head gasket sitting loosely on top of a four-cylinder 1989 Vauxhall Astra engine block. Once positioned correctly the cylinder head will be bolted down on top of it, using a torque wrench.

A head gasket is a gasket that sits between the engine block and cylinder head in an internal combustion engine. Its purpose is to seal the cylinders to ensure maximum compression and avoid leakage of coolant or engine oil into the cylinders; as such, it is the most critical sealing application in any engine, and, as part of the combustion chamber, it shares the same strength requirements as other combustion chamber components.[1]

Contents

Types

  • MLS or Multiple Layers Steel – Most modern head engines are produced with MLS gaskets. These typically consist of three layers of steel. The contact faces are usually coated with a rubber-like coating such as Viton that adheres to the cylinder block and cylinder head while the thicker center layer is left bare.
  • Solid copper – a solid sheet of copper, and typically requires special machining called 'o-ringing' that places a piece of wire around the circumference of the cylinder to bite into the copper. When this is performed copper gaskets are extremely durable. Recently companies have started producing copper gaskets with integral sealing wires permitting their retrofit into engines without the removal of the engine block for machine work.
  • Composite – an older technology. Typically these are made from asbestos or graphite but are more prone to blowouts than newer gaskets. Asbestos gaskets are becoming increasingly rare due to health concerns.[2]
  • Elastomeric – a gasket type used by Rover on their K Series engines. It utilised a steel core plate with molded in place silicon rubber beads to seal oil and coolant passages. The bores were sealed by rolled steel fire rings in a more conventional manner. The idea behind the gasket design was to produce a production version of the technology used in F1 engines at the time. The original application of the gasket on the smaller versions of the K Series was very successful. However, an engine redesign resulted in persistent problems with the design – the joint interface became unstable and the gasket could not cope.

Gasket problems

Occasionally, the compression in the cylinder will cause a leak to form in the gasket and the gasket will have to be replaced, or severe damage can take place (a "blown" head gasket). This problem has been exacerbated by the use of aluminum rather than iron cylinder heads; while lighter than iron, aluminum has a much greater thermal expansion rate, which in turn causes a great deal more stress to be placed on the head gasket. Engine makers have responded to this by adding a non-stick coating such as Teflon to the surface of the head gasket.

If the gasket fails, a variety of problems can occur, from compression loss (leading to power reduction, or a rough engine), to exhaust gases being forced into the cooling system, leading to the engine overheating and increased engine wear due to the motor oil being mixed with antifreeze. Coolant can leak into the cylinders, causing the exhaust to issue steam[3] and the catalytic converter to be damaged. If a very large amount of coolant does this, hydrolock can occur, causing extensive engine damage. Sometimes, all that may happen when a head gasket is blown is excessive steam erupting from the tailpipe; yet the engine may act and drive like normal, until all the coolant is gone and the engine overheats. In other occurrences, compression leaks into small spaces between the gasket and either the cylinder head or engine block trap air that is then released when the engine is turned off, which then escape into the coolant and create air pockets. Sometimes, these air pockets can get trapped in the engines coolant thermostat, causing it to stay closed and further the overheating issue, thereby creating still more voids between the gasket and the engine. Air pockets can also cause the engine to expel coolant into the overflow or expansion tank, thereby reducing the amount of coolant the engine has available to stay cool.

A damaged head gasket can allow gases to leak between cylinders.

The condition of a head gasket is typically investigated by checking the compression pressure with a pressure gauge, or better, a leak-down test, and/or noting any indication of combustion gases in the cooling system on a water-cooled engine. Oil mixed with coolant and excessive coolant loss with no apparent cause, or presence of carbon monoxide or hydrocarbon gases in the expansion tank of the cooling system can also be signs of head gasket problems. A good sign of head gasket failure on water-cooled engines is the presence of a substance that resembles mayonnaise in the oil, often to be seen on the dipstick, or oil filler cap. However, the presence of this substance is not conclusive proof of head gasket failure, since oil could mix with the coolant via other routes.

A leaking head gasket can be classified as either external or internal. An external leak can be identified as oil and coolant accumulating underneath the engine. The presence of coolant can be detected by shining a black light on what appears to be an oil leak; the appearance of coolant will show up under the black light. External leaks can also appear as previously described in the oil. An internal leak can usually be diagnosed by excessive coolant accumulating in the expansion tank along with the presence of hydrocarbons in the form of foam.

Blue exhaust smoke may be indicative of oil burning. White exhaust smoke is an indicator of coolant burning, another sign of head gasket wear.

References

  1. ^ Bickford, John H. (1997). Gaskets and Gasketed Joints. CRC Press. p. 57. ISBN 0-824-798-775. 
  2. ^ Nunney, M. J. (1998). Light & Heavy Vehicle Technology. Elsevier. p. 23. ISBN 0-750-638-273. "Since exposure to asbestos is now recognized as being a health hazard [...] the manufacture of non-asbestos cylinder head gaskets has now become established." 
  3. ^ Nunney, p. 23.

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • head gasket — The gasket at the top of the cylinder and sits between the cylinder and the head. It keeps the coolant out of the cylinders and retains compression in the cylinder. Also called cylinder head gasket. Also see blown head gasket …   Dictionary of automotive terms

  • head gasket — noun a gasket to seal a cylinder head • Hypernyms: ↑gasket …   Useful english dictionary

  • head gasket — noun the gasket which fits between the cylinder head and the cylinders or cylinder block in an internal combustion engine …   English new terms dictionary

  • cylinder head gasket — See head gasket …   Dictionary of automotive terms

  • blown head gasket — A gasket that has a break between the opening for the cylinder and an opening for the coolant. The coolant will leak into the combustion chamber. This condition can be diagnosed by a loss in coolant and white smoke out the exhaust …   Dictionary of automotive terms

  • Gasket — [ thumb|sright|250px|Some seals and gaskets 1. o ring 2. fiber washer 3. paper gaskets 4. cylinder head gasket] A gasket is a mechanical seal that fills the space between two objects, generally to prevent leakage between the two objects while… …   Wikipedia

  • gasket — A material made of asbestos, cardboard, cork, paper, rubber, or soft metal placed between two metal parts to insure proper sealing. Also see base gasket blown head gasket cylinder head gasket head gasket liquid gasket oil pan gasket rocker cover… …   Dictionary of automotive terms

  • head — [1] The upper part of something. [2] A term used to express the increase of energy content in a fluid pumped, expressed in units of energy per unit of mass, usually simply ft (feet). [3] A part of the engine which covers the piston and creates… …   Dictionary of automotive terms

  • gasket — /ˈgæskət / (say gaskuht) noun 1. anything used as a packing or jointing material for making joints fluid tight. 2. a suitably punched asbestos sheet, usually sandwiched between thin sheets of copper, for making a gastight joint, especially… …  

  • top end gasket kit — The gaskets that apply to everything from the base gasket up (e.g., base gasket, head gasket, manifold gaskets, carburetor mounting gaskets) as well as all the O rings and replaceable spacers. Contrasts with the bottom end gasket kit …   Dictionary of automotive terms

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”