Torsion beam suspension


Torsion beam suspension

A torsion bar suspension, also known as a torsion spring suspension or incorrectly torsion beam, is a general term for any vehicle suspension that uses a torsion bar as its main weight bearing spring. One end of a long metal bar is attached firmly to the vehicle chassis; the opposite end terminates in a lever, mounted perpendicular to the bar, that is attached to a suspension arm, spindle or the axle. Vertical motion of the wheel causes the bar to twist around its axis and is resisted by the bar's torsion resistance. The effective spring rate of the bar is determined by its length, diameter and material.

Torsion bar suspensions are currently used on trucks and SUV from Ford, Dodge, GM and Mitsubishi. Manufacturers change the torsion bar or key to adjust the ride height, usually to compensate for heavier or lighter engine packages. While the ride height may be adjusted by turning the adjuster bolts on the stock torsion key, rotating the stock keys too far can bend the adjusting bolt and (more importantly) place the shock piston outside the standard travel. Over-rotating the torsion bars can also cause the suspension to hit the bump stop prematurely, causing a harsh ride. Aftermarket forged torsion key kits use re-clocked adjuster keys to prevent over-rotation, as well as shock brackets that keep the piston travel in the stock position.

The main advantages of torsion bar suspension are durability, easy adjustability of ride height, and small profile along the width of the vehicle. It takes up less of the vehicle's interior volume compared to coil springs. A major disadvantage is that torsion bars, unlike coil springs, usually cannot provide a progressive spring rate, forcing designers to compromise between ride quality and handling ability—progressive torsion bars are available, but at the expense of durability since they have a tendency to crack where the diameter of the bar changes. In most torsion bar systems, especially Chrysler's, ride height (and therefore many handling features) may be adjusted by bolts which connect the torsion bars to the steering knuckles and require nothing more than crawling under the car with a wrench in hand. In most cars which use this type of suspension, swapping torsion bars for those with a different spring rate is usually an extremely easy task.

Some vehicles use torsion bars to provide automatic leveling, using a motor to tighten the bars to provide greater resistance to load and, in some cases (depending on the speed with which the motors can act), to respond to changes in road conditions. Height adjustable suspension has been used to implement a wheel-change mode where the vehicle is raised on three wheels and the remaining wheel is lifted off the ground without the aid of a jack.

Before World War II, the front wheel drive Citroen Traction Avant (1934) had independent front torsion bar suspension and a trailing dead axle, also sprung by torsion bars. The Czechoslovakian Tatra cars designed by Professor Hans Ledwinka in the mid-1930s used all round independent torsion bar suspension, along with air cooled rear engines. Also in the 1930s, prototypes of the first Volkswagen Beetle incorporated torsion bars—especially its transverse mounting style. Ledwinka's concept had been copied by Ferdinand Porsche, whose successors later had to acknowledge the influence of Ledwinka's Tatra models on the Porsche-designed Kdf-Wagen of 1938 (later known as the VW Beetle), a post-war lawsuit resulting in a DM3,000,000 settlement paid by Volkswagen to Ringhoffer-Tatra in 1961.

The system was applied to many new armored fighting vehicle designs during the Second World War. It was used extensively in European cars Renault, Citroën and Volkswagen, as well as by Packard in the 1950s. The Packard used torsion bars at both front and rear, and interconnected the front and rear systems to improve ride quality. The most famous American passenger-car application was the Chrysler system used beginning with the 1957 model year, although Chrysler's "Torsion-Aire" suspension was only for the front; the same basic system (longitudinal mounting) was maintained until the 1981 introduction of the K-car. A reengineered torsion bar suspension, introduced with the 1976 Dodge Aspen, introduced transverse-mounted torsion bars (possibly based on the Volkswagen Type 3 passenger car) until production ended in 1989 (with Chrysler's M platform). Light-duty Dodge trucks however continue to use torsion bars on their front suspension.

General Motors has used torsion bars since 1966, starting with the E-platform vehicles (Oldsmobile Toronado, Cadillac Eldorado), 4 wheel drive S-10 pickups, and since 1988, full size trucks (GMT400, GMT800, and GMT900 series).

Some front-wheel drive automobiles use a related type of torsion beam suspension, usually called a twist-beam rear suspension, in which the rear wheels are carried on trailing arms connected by a laterally mounted torsion beam. The torsion beam functions both as wheel-locating arm and as an anti-roll bar to resist lateral motion of the wheels as the body leans in turns. Its advantages are that it is inexpensive to manufacture and install, and engages a minimum amount of interior volume, leaving more space for the carriage of passengers, cargo, and other components. Because the torsion beam acts in the lateral plane, not vertically, the twist-beam axle cannot provide ride-height adjustment, and it suffers, to some extent, similar car handling limitations as other beam axle suspensions. However these limitations may not be apparent on the road, because of the trend towards firmer, more sporty suspension setups with more limited wheel travel. Torsion-beam rear suspensions were pioneered on the Volkswagen GolfFact|date=February 2007 in the early 1970s, and remain common on compact cars and minivans.

External links

* [http://www.autozine.org/technical_school/suspension/tech_suspension21.htm#Torsion AutoZine Technical School site]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Suspension (vehicle) — Suspension is the term given to the system of springs, shock absorbers and linkages that connects a vehicle to its wheels. Suspension systems serve a dual purpose – contributing to the car s handling and braking for good active safety and driving …   Wikipedia

  • Torsion spring — A mousetrap powered by a helical torsion spring A torsion spring is a spring that works by torsion or twisting; that is, a flexible elastic object that stores mechanical energy when it is twisted. The amount of force (actually torque) it exerts… …   Wikipedia

  • suspension — [1] The assembly of springs, shock absorbers, torsion bars, joints, arms, etc., that cushions the shock of bumps on the road and serves to keep the wheels in constant contact with the road, thereby improving control and traction. [2] A mixture of …   Dictionary of automotive terms

  • Double wishbone suspension — Wishbones and upright painted yellow In automobiles, a double wishbone (or upper and lower A arm) suspension is an independent suspension design using two (occasionally parallel) wishbone shaped arms to locate the wheel. Each wishbone or arm has… …   Wikipedia

  • Horstmann suspension — is a type of tank and other tracked armoured fighting vehicle suspension devised by the British engineer Sidney Horstmann in 1922.The system uses coil springs and has the advantages of a relatively long travel and, consisting of a self contained… …   Wikipedia

  • List of structural engineering topics — This page aims to list all articles related to the specific discipline of structural engineering. For a broad overview of engineering, please see List of engineering topics. For biographies please see List of engineers.compactTOC NOTOC AA frame… …   Wikipedia

  • Sway bar — A sway bar (also stabilizer bar, anti sway bar, roll bar, or anti roll bar, ARB) is an automobile suspension device. It connects opposite (left/right) wheels together through short lever arms linked by a torsion spring. A sway bar increases the… …   Wikipedia

  • Eighth-generation Honda Civic — Infobox Automobile generation name=Eighth generation (FA/FG/FK/FN/FD) wheelbase=104.3 in (264 cm) (coupe) 106.3 in (270 cm) (sedan) 103.7 in (263.5 cm) (hatchback) length=174.8 in (441 cm) (2006 08 coupe) Auto in|175.5|0 (2009 coupe) 176.7 in… …   Wikipedia

  • Proton Saga — Infobox Automobile boxcolor = red name = Proton Saga manufacturer = Proton production = 1985 ndash;present class = Compact Subcompact platform = layout= FF layout body style = 4 door saloon 5 door hatchback engine = weight = predecessor =… …   Wikipedia

  • List of mechanical engineering topics — This page aims to list all articles related to the specific discipline of mechanical engineering. For a broad overview of engineering, please see List of engineering topics. For biographies please see List of engineers.compactTOC NOTOC… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.