Slave clock

Slave clock

In telecommunication, a slave clock is a clock that is coordinated with a master clock. Slave clock coordination is usually achieved by phase-locking the slave clock signal to a signal received from the master clock. To adjust for the transit time of the signal from the master clock to the slave clock, the phase of the slave clock may be adjusted with respect to the signal from the master clock so that both clocks are in phase. Thus, the time markers of both clocks, at the output of the clocks, occur simultaneously.

In other areas, the term refers to satellite electrical clocks that operate remotely from an electrical pulse issued by a master clock. In the 19th and early 20th centuries, slave clocks were widely used throughout public buildings and business offices, and their remote operation was regulated by electrical signals sent by a centralized master clock.

Source: from Federal Standard 1037C

These older styles of slave clocks either keep time by themselves, and are corrected by the master clock, or require impulses from the master clock to advance. Many slave clocks of these types remain in operation, most commonly in schools.

IBM/Simplex Synchronous Correction cycle.

Synchronous Systems

This type system was developed by IBM in the late 1940s. IBM sold their time division to the Simplex Time Recorder Company in 1958. The methods & clock mechanisms have remained basically unchanged, other than appearance & style over the years. Today, this same protocol is used by several manufacturers, including Latham, Dukane, Cincinnati & Standard Electric Time. Digital master clocks have replaced older mechanical types.

All consist of a master clock & a number of secondary clocks in remote locations. These secondary clocks appear to run like an ordinary plug-in electric clock & run on their own synchronous electric motor and will maintain correct time unless there is an interruption in electric service, depending on the master clock only for the periodic synchronizing impulse. These clocks differ from the ‘impulse’ type, which are electrically advanced each minute by the master clock. Impulse type clocks are usually called ‘slave’ clocks since they cannot function at all without the master clock.

There are two basic variations in synchronous systems, ’wired’ & ‘electronic’.

In a wired system, the secondary clocks are ‘hard-wired’ to the master clock with their own network of wiring. This dedicated wiring consists of 3 wires & requires that all secondary clocks be connected to this network in order to receive corrections from the master clock. These systems are usually 110 volts but some are 24 volts. The master clock energizes the third wire to apply voltage to the correction solenoids(called ‘clutch magnets’ by the manufacturer) in the secondary clocks.

In an ‘electronic’ system, the correction impulse is applied to the normal building wiring, in the form of a high-frequency audio signal (typically 3510 Hz) applied to the normal 60 Hz frequency of the electrical system. Special receivers in the secondary clocks receive this impulse & apply voltage to the correction solenoid. In this type system, secondary clocks need no special wiring & may be plugged into any 110 volt outlet in the building.

The cycle can also be initiated manually for testing & adjustment as follows:With clock running, rotate 90 degrees to the right, so that the ‘9’ is at the top. Hold in this position approximately 8 seconds (you may hear a clicking sound during this time), then return the clock to it’s normal upright position. Within 60 seconds, the hands will slowly advance to the next hour as described below in the third paragraph ** under ‘Hourly Correction’.

The actual correction that follows is the same in both types of systems. The only difference (described above) is the method by which the correction solenoid is energized.

Hourly CorrectionThe correction impulse is issued by the system master clock at 57 minutes 54 seconds after each hour & lasts for 8 seconds (until 58 minutes 02 seconds). The correction solenoids in the secondary clocks are energized by this pulse. This causes the attached armature & cam to engage a gear & rotate upwards to lift a latch allowing the correction cycle to begin. This takes 6 seconds & causes the secondary clocks to begin their correction cycle at precisely 58 minutes 0 seconds.

The correction cycle lasts precisely 60 seconds, ending at 59 minutes 0 seconds at which time, all clocks in the system will display the same time as the master clock.

** The cycle causes an internal clock-wise sweep, beginning at the 59 minute position & takes 60 seconds, rotating around the dial, ending at the 59 minute position. During this sweep, if the minute hand is not in proper position, when the sweep rotation reaches it, the minute hand is slowly rotated at 1 rpm until it reaches the 59 minute mark. At this point it is now in sync with the master clock.

During the cycle, the red second hand continues its normal 1 rpm motion but is held in place when it reaches the 60 second mark. It is released when the cycle is complete (minute hand reaches 59 minutes) & now minutes & seconds are both in sync with the master clock.

12 Hour CorrectionThis impulse is issued by the system master clock at 5:57:54 AM & PM & is a longer version of the hourly correction impulse. Instead of lasting 8 seconds, this impulse is of 14 seconds duration, lasting until 58 minutes, 08 seconds. The cams in the secondary clocks are rotated further & lock the correction cycle latch open, causing the cycle to continue until the clocks reach 5:59:00. Depending on how many hours the secondary clocks were slow, they will now be several minutes slower than the master. This error is then corrected by the next normal hourly correction at 6:57:54.

source: National Association of Watch and Clock Collectors posting

Pictures

Mechanical slave clocks from the 1950s and 1960s era.


External links

* http://www.bmumford.com/clocks/driver/driver.html/ Slave Driver Company
* http://www.piexx.com/index.php?main_page=product_info&products_id=5/ Imp 2 Slave Driver
* http://homepage.ntlworld.com/follies/ All about electric master and slave clocks


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • slave clock — noun : the auxiliary apparatus of a precision astronomical clock that relieves the latter of nearly all the work and thus assures uniformity of performance …   Useful english dictionary

  • Clock — For other uses, see Clock (disambiguation). Timepiece redirects here. For the Kenny Rogers album, see Timepiece (album). Platform clock at King s Cross railway station, London …   Wikipedia

  • Slave (disambiguation) — A slave is a person whose labor is exploited through slaverySlave may also refer to: * Slave is African American slang for job . * Slave bell, a brass bell used to regulate slavery at the Cape Colony * The Slave craton, an Archaean land mass in… …   Wikipedia

  • clock — clock1 /klok/, n. 1. an instrument for measuring and recording time, esp. by mechanical means, usually with hands or changing numbers to indicate the hour and minute: not designed to be worn or carried about. 2. See time clock. 3. a meter or… …   Universalium

  • Clock network — A clock network or clock system is a set of clocks designed to always show exactly the same time by communicating with each other. Clock networks usually include a central master clock kept in sync with an official time source, and one or more… …   Wikipedia

  • Slave station — *Historically a slave station was the collection and transfer location utilized in the slave trade for handling human slaves. One famous slave station, on Goree Island, is now a museum in Senegal.*In telecommunications, the term slave station, or …   Wikipedia

  • Pendulum clock — A pendulum clock is a clock that uses a pendulum, a swinging weight, as its timekeeping element. From its invention in 1656 by Christiaan Huygens until the 1930s, the pendulum clock was the world s most accurate timekeeper, accounting for its… …   Wikipedia

  • Shepherd gate clock — The Shepherd Gate Clock is the clock mounted on the wall outside the gate of the Royal Greenwich Observatory building in Greenwich, London. The clock, an early example of an electric clock, was a slave mechanism controlled by electric pulses… …   Wikipedia

  • Reference clock — In telecommunication, the term reference clock has the following meanings: * A clock with which another clock is compared. * A clock, usually of high stability and accuracy, used to govern a network of mutually synchronized clocks of lower… …   Wikipedia

  • Master clock — (at left) driving several slave clocks. Note third one along at the top from the right is a radio controlled quartz for reference A master clock is a precision clock that provides timing signals to synchronize slave clocks as part of a clock… …   Wikipedia

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”