Heat pipe


Heat pipe

A heat pipe is a heat transfer mechanism that can transport large quantities of heat with a very small difference in temperature between the hotter and colder interfaces.

Inside a heat pipe, at the hot interface a fluid turns to vapour and the gas naturally flows and condenses on the cold interface. The liquid falls or is moved by capillary action back to the hot interface to evaporate again and repeat the cycle.

tructure, Design and Construction

A typical heat pipe consists of a sealed pipe or tube made of a material with high thermal conductivity such as copper or aluminium. A vacuum pump is used to exclude all fluids (both gases and liquids) from the empty heat pipe, and then the pipe is filled with a fraction of a percent by volume of "working fluid", (or coolant), chosen to match the operating temperature. Some example fluids are water, ethanol, acetone, sodium, or mercury. Due to the partial vacuum that is near or below the vapor pressure of the fluid, some of the fluid will be in the liquid phase and some will be in the gas phase.

Inside the pipe's walls, an optional wick structure exerts a capillary pressure on the liquid phase of the working fluid. This is typically a sintered metal powder or a series of grooves parallel to the pipe axis, but it may be any material capable of exerting capillary pressure on the condensed liquid to wick it back to the heated end. The heat pipe may not need a wick structure if gravity or some other source of acceleration is sufficient to overcome surface tension and cause the condensed liquid to flow back to the heated end.

A heat pipe is not a thermosiphon, because there is no siphon. Thermosiphons transfer heat by single-phase convection. (See also: Perkins Tube, after Jacob Perkins.)

Heat pipes contain no mechanical moving parts and typically require no maintenance, though non-condensing gases (that diffuse through the pipe's walls, result from breakdown of the working fluid, or exist as impurities in the materials) may eventually reduce the pipe's effectiveness at transferring heat. This is significant when the working fluid's vapour pressure is low.

The materials chosen depend on the temperature conditions in which the heat pipe must operate, with coolants ranging from liquid helium for extremely low temperature applications (2–4 K) to mercury (523–923 K) & sodium (873–1473 K) and even indium (2000–3000 K) for extremely high temperatures. The vast majority of heat pipes for low temperature applications use some combination of ammonia (213–373 K), alcohol (methanol (283–403 K) or ethanol (273–403 K)) or water (303–473 K) as working fluid.

The advantage of heat pipes is their great efficiency in transferring heat. They are a much better heat conductor than an equivalent cross-section of solid copper. A heat flux of more than 230 MW/m² has been recorded (nearly four times the heat flux at the surface of the sun). [Jim Danneskiold, [http://www.lanl.gov/news/releases/archive/00-064.shtml Los Alamos-developed heat pipes ease space flight] . Los Alamos News Release, April 26, 2000.]

Heating a volatile liquid at a fixed volume can be dangerous, since the pressure can exceed the strength of the container (see pressure vessel). The pipe must safely withstand the pressure that occurs when all of the fluid is in the vapor phase at high temperature. Most importantly, the maximum pressure in the heat pipe must be limited by carefully restricting the total mass of working fluid.

Active control of heat flux can be effected by adding a variable volume liquid reservoir to the evaporator section. Variable conductance heat pipes employ a large reservoir of inert immiscible gas attached to the condensing section. Varying the gas reservoir pressure changes the volume of gas charged to the condenser which in turn limits the area available for vapor condensation. Thus a wider range of heat fluxes and temperature gradients can be accommodated with a single design.

A modified heat pipe with a reservoir having no capillary connection to the heat pipe wick at the evaporator end can also be used as a thermal diode. This heat pipe will transfer heat in one direction, acting as an insulator in the other.

Flat heat pipes

Thin planar heat pipes (heat spreaders) have the same primary components as tubular heat pipes. These components are a hermetically sealed hollow vessel, a working fluid, and a closed-loop capillary recirculation system.

Compared to a one-dimensional tubular heat pipe, the width of a two-dimensional heat pipe allows an adequate cross section for heat flow even with a very thin device. These thin planar heat pipes are finding their way into “height sensitive” applications, such as notebook computers, and surface mount circuit board cores. It is possible to produce flat heat pipes as thin as 0.5 mm (thinner than a credit card).

Heat transfer

Heat pipes employ evaporative cooling to transfer thermal energy from one point to another by the evaporation and condensation of a working fluid or coolant. Heat pipes rely on a temperature difference between the ends of the pipe, and cannot lower temperatures at either end beyond the ambient temperature (hence they tend to equalise the temperature within the pipe).

When one end of the heat pipe is heated the working fluid inside the pipe at that end evaporates and increases the vapour pressure inside the cavity of the heat pipe. The latent heat of evaporation absorbed by the vaporisation of the working fluid reduces the temperature at the hot end of the pipe.

The vapour pressure over the hot liquid working fluid at the hot end of the pipe is higher than the equilibrium vapour pressure over condensing working fluid at the cooler end of the pipe, and this pressure difference drives a rapid mass transfer to the condensing end where the excess vapour condenses, releases its latent heat, and warms the cool end of the pipe. Non-condensing gases (caused by contamination for instance) in the vapour impede the gas flow and reduce the effectiveness of the heat pipe, particularly at low temperatures, where vapour pressures are low. The velocity of molecules in a gas is approximately the speed of sound and in the absence of non condensing gases, this is the upper velocity with which they could travel in the heat pipe. In practice, the speed of the vapour through the heat pipe is dependent on the rate of condensation at the cold end.

The condensed working fluid then flows back to the hot end of the pipe. In the case of vertically-oriented heat pipes the fluid may be moved by the force of gravity. In the case of heat pipes containing wicks, the fluid is returned by capillary action.

When making heat pipes, there is no need to create a vacuum in the pipe. One simply boils the working fluid in the heat pipe until the resulting vapour has purged the non condensing gases from the pipe and then seals the end.

An interesting property of heat pipes is the temperature over which they are effective. Initially, it might be suspected that a water charged heat pipe would only work when the hot end reached the boiling point (100 °C) and steam was transferred to the cold end. However, the boiling point of water is dependent on absolute pressure inside the pipe. In an evacuated pipe, water will boil just slightly above its melting point (0 °C). The heat pipe will operate, therefore, when the hot end is just slightly warmer than the melting point of the working fluid. Similarly, a heat pipe with water as a working fluid can work well above the boiling point (100 °C), if the cold end is low enough in temperature to condense the fluid.

The main reason for the effectiveness of heat pipes is the evaporation and condensation of the working fluid. The heat of vaporization greatly exceeds the sensible heat capacity. Using water as an example, the energy needed to evaporate one gram of water is equivalent to the amount of energy needed to raise the temperature of that same gram of water by 540 °C (hypothetically, if the water was under extremely high pressure so it didn't vaporize or freeze over this temperature range). Almost all of that energy is rapidly transferred to the "cold" end when the fluid condenses there, making a very effective heat transfer system with no moving parts.

Origins and research in the United States

The general principle of heat pipes using gravity (commonly classified as two phase thermosiphons) dates back to the steam age. The modern concept for a capillary driven heat pipe was first suggested by R.S. Gaugler of General Motors in 1942 who patented the idea. [Citation
first = Richard
last = Gaugler
assignee = General Motors Corporation
title = Heat Transfer Devices
year = 1944
pages = 4
place = Dayton, Ohio
publisher = U.S. Patent Office
id = 2350348
] The benefits of employing capillary action were independently developed and first demonstrated by George Grover at Los Alamos National Laboratory in 1963 and subsequently published in the Journal of Applied Physics in 1964. [cite journal
author = Grover, G.M., T. P. Cotter, and G. F. Erickson
year = 1964
title = Structures of Very High Thermal Conductance
journal = Journal of Applied Physics
volume = 35
issue = 6
pages = 1990–1991.
doi = 10.1063/1.1713792
] Grover noted in his notebook: [ [http://www.lanl.gov/orgs/esa/epe/Heat_Pipe_Site/ancient.shtml Heat Pipe research at LANL] ]

"Heat transfer via capillary movement of fluids. The "pumping" action of surface tension forces may be sufficient to move liquids from a cold temperature zone to a high temperature zone (with subsequent return in vapor form using as the driving force, the difference in vapor pressure at the two temperatures) to be of interest in transferring heat from the hot to the cold zone. Such a closed system, requiring no external pumps, may be of particular interest in space reactors in moving heat from the reactor core to a radiating system. In the absence of gravity, the forces must only be such as to overcome the capillary and the drag of the returning vapor through its channels."

Between 1964 and 1966, RCA was the first corporation to undertake research and development of heat pipes for commercial applications (though their work was mostly funded by the US government). During the late 1960s NASA played a large role in heat pipe development by funding a significant amount of research on their applications and reliability in space flight following from Grover's suggestion. NASA’s attraction to heat pipe cooling systems was understandable given their low weight, high heat flux, and zero power draw. Their primary interest however was based on the fact that the system wouldn’t be adversely affected by operating in a zero gravity environment. The first application of heat pipes in the space program was in thermal equilibration of satellite transponders. As satellites orbit one side is exposed to the direct radiation of the sun while the opposite side is completely dark and exposed to the deep cold of outer space. This causes severe discrepancies in the temperature (and thus reliability and accuracy) of the transponders. The heat pipe cooling system designed for this purpose managed the high heat fluxes and demonstrated flawless operation with and without the influence of gravity. The developed cooling system was the first description and usage of variable conductance heat pipes to actively regulate heat flow or evaporator temperature.

Corporate R&D

Publications in 1967 and 1968 by Feldman, Eastman, & Katzoff first discussed applications of heat pipes to areas outside of government concern and that did not fall under the high temperature classification such as; air conditioning, engine cooling, and electronics cooling. These papers also made the first mentions of flexible, arterial, and flat plate heat pipes. 1969 publications introduced the concepts of the rotational heat pipe with its applications to turbine blade cooling and the first discussions of heat pipe applications to cryogenic processes.

Starting in the 1980s Sony began incorporating heat pipes into the cooling schemes for some of its commercial electronic products in place of both forced convection and passive finned heat sinks. Initially they were used in tuners & amplifiers, soon spreading to other high heat flux electronics applications. During the late 1990s increasingly hot microcomputer CPUs spurred a threefold increase in the number of U.S. heat pipe patent applications. As heat pipes transferred from a specialized industrial heat transfer component to a consumer commodity most development and production moved from the U.S. to Asia. Modern CPU heat pipes are typically made from copper and use water as the working fluid.

Applications

Grover and his colleagues were working on cooling systems for nuclear power cells for space craft, where extreme thermal conditions are found. Heat pipes have since been used extensively in spacecraft as a means for managing internal temperature conditions.

Heat pipes are extensively used in many modern computer systems, where increased power requirements and subsequent increases in heat emission have resulted in greater demands on cooling systems. Heat pipes are typically used to move heat away from components such as CPUs and GPUs to heat sinks where thermal energy may be dissipated into the environment.

olar Thermal

Heat pipes are also being widely used in solar thermal water heating applications in combination with evacuated tube solar collector arrays. In these applications, distilled water is commonly used as the heat transfer fluid inside a sealed length of copper tubing that is located within an evacuated glass tube and oriented towards the sun.

In solar thermal water heating applications, an evacuated tube collector can deliver up to 40% more efficiency compared to more traditional "flat plate" solar water heaters. Evacuated tube collectors eliminate the need for anti-freeze additives to be added as the vacuum helps prevent heat loss. These types of solar thermal water heaters are frost protected down to more than -3 °C and are being used in Antarctica to heat water.

Pipelines over permafrost

Heat pipes are used to dissipate heat on the Trans-Alaska Pipeline System. Heat produced by friction and turbulence in the moving oil would conduct down the pipe's support legs and melt the permafrost which anchors them. Heat pipes with radiators at the top are used on each leg to keep them cold so they won't melt the permafrost and let the pipeline collapse.

Limitations

Heat pipes must be tuned to particular cooling conditions. The choice of pipe material, size and coolant all have an effect on the optimal temperatures in which heat pipes work.

When heated above a certain temperature, all of the working fluid in the heat pipe will vaporize and the condensation process will cease to occur; in such conditions, the heat pipe's thermal conductivity is effectively reduced to the heat conduction properties of its solid metal casing alone. As most heat pipes are constructed of copper (a metal with high heat conductivity), an overheated heatpipe will generally continue to conduct heat at around 1/80 of the original conductivity.

In addition, below a certain temperature, the working fluid will not undergo phase change, and the thermal conductivity will be reduced to that of the solid metal casing. One of the key criteria for the selection of a working fluid is the desired operational temperature range of the application. The lower temperature limit typically occurs a few degrees above the freezing point of the working fluid.

References

Heat Pipe Science and Technology, Amir Faghri, Taylor and Francis 1995.

ee also

*Thermosiphon: A similar mechanism in which thermal energy is transferred by fluid buoyancy rather than evaporation and condensation.
*Vapor-compression refrigeration
*Evaporative cooling
*Heat sink
*CPU cooling
*Aircooling
*Watercooling
*Peltier or thermoelectric cooling
*Loop heat pipe

External links

* [http://architecture.mit.edu/house_n/web/resources/tutorials/House_N%20Tutorial%20Heat%20Pipes.htm House_N Research (mit.edu)]
* [http://www.cheresources.com/htpipes.shtml What is a Heat Pipe?]
* [http://www.enertron-inc.com/enertron-resources/PDF/How-to-select-a-heat-pipe.pdf Heat pipe selection guide (pdf)]
* [http://www.metal-process.fr/fonctionnement_e.html Mechanism]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Heat pipe — Saltar a navegación, búsqueda Disipador de aluminio con una heat pipe pichar. Heat pipe (literalmente en español tubería de calor, aunque el término no suele traducirse), es un tubo con alta conductividad usado como disipador de calor. Consiste… …   Wikipedia Español

  • heat pipe — n. a thin, sealed metal tube that efficiently transfers heat without a pump, using a fluid that vaporizes at the hot end, condenses as it reaches the cooler end, and returns to the hot end by capillary action through a wick or along tiny grooves… …   Universalium

  • heat pipe — n. a thin, sealed metal tube that efficiently transfers heat without a pump, using a fluid that vaporizes at the hot end, condenses as it reaches the cooler end, and returns to the hot end by capillary action through a wick or along tiny grooves… …   English World dictionary

  • Heat-Pipe — Ein Wärmerohr ist ein Wärmeüberträger, der unter Nutzung von Verdampfungswärme eines Stoffes eine hohe Wärmestromdichte erlaubt, d. h. auf kleiner Querschnittsfläche können große Mengen Wärme transportiert werden. Beispielsweise kann die… …   Deutsch Wikipedia

  • Heat Pipe — Ein Wärmerohr ist ein Wärmeüberträger, der unter Nutzung von Verdampfungswärme eines Stoffes eine hohe Wärmestromdichte erlaubt, d. h. auf kleiner Querschnittsfläche können große Mengen Wärme transportiert werden. Beispielsweise kann die… …   Deutsch Wikipedia

  • heat pipe — noun : a closed container in which a continuing cycle of evaporation and condensation of a fluid takes place with the heat being given off at the condenser end and which is more effective in transferring heat than a metallic conductor * * * heat… …   Useful english dictionary

  • Heat-pipe — Caloduc Les multiples ailettes en aluminium évacuent la chaleur des caloducs (tuyauterie). Il s agit ici d un ventirad haut de gamme (Cooler Master V8) …   Wikipédia en Français

  • Heat pipe — Caloduc Les multiples ailettes en aluminium évacuent la chaleur des caloducs (tuyauterie). Il s agit ici d un ventirad haut de gamme (Cooler Master V8) …   Wikipédia en Français

  • heat pipe — /ˈhit paɪp/ (say heet puyp) noun a device for heat transfer based on vaporisation and capillary action, which is more effective in transporting heat than metallic conductors …   Australian English dictionary

  • Heat Pipe —   A device that transfers heat by the continuous evaporation and condensation of an internal fluid …   Energy terms


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.