Forced induction

Forced induction

Forced induction is a term used to describe internal combustion engines that are not naturally aspirated. Instead, a gas compressor is added to the air intake, thereby increasing the quantity of oxygen available for combustion. This compressed air is normally referred to as Boost or charge air.

Introduction

Forced induction can be used to improve the power, efficiency, emissions, or combinations of same, without much extra weight and minimal modifications to the engine architecture. The two most common forms of forced induction are turbochargers and superchargers, which both compress the air entering the cylinders, but use different methods to obtain the requisite power. Functionally, they are much the same. Since only so much power can be had from a given amount of gasoline, the more gasoline can be burned in the cylinder, the more power can be produced. However, simply adding more gas beyond the optimal air/fuel ratio (commonly called "running rich") does nothing for power. An engine can only take in so much when breathing air at atmospheric pressures, since the capacity and number of cylinders is non-variable. Hence, the only way to get more air into the cylinder, and therefore produce more power, is to increase the pressure at the intake.

All we've considered up to now is increased power, so how does forced induction improve emissions or efficiency? One of the primary concerns in internal combustion emissions is a factor called the NOx fraction, or the amount of nitrogen/oxygen compounds the engine produces. High combustion temperatures lead to a lower NOx fraction, and since gasses heat when compressed, the more gas is compressed in a given volume, the hotter it will get, and the lower the NOx fraction will be. Since forced induction increases the amount of gas being compressed, it increases the heat generated when compression occurs. Since colder air is denser, it is most desirable, from a power standpoint, to have cold air coming in, but better from an emissions standpoint if the air is hot. In a perfect world, incoming air would be frigid, and the compression would be high enough to dramatically and rapidly increase cylinder temperatures, reducing emissions significantly.

Two of the commonly used forced induction technologies are turbochargers and superchargers. They differ primarily in the power source for the compressor. There is a difference between forced induction and power adders. A power adder is anything that improves an engine's power output, which does not necessarily mean increasing charge density. Oxidizing technologies such as nitrous oxide injection systems provide improved power, but are not a form of forced induction.

Comparison

Strengths and weaknesses vary according to the method of forcing induction largely based upon the inherent design functions of both. A turbocharger acts as an obstacle to exhaust gases due to its placement in the exhaust system tract. A supercharger uses torque generated from the rotational mass internal to the engine through the crank pulley. A turbo relies on the volume and velocity of exhaust gases to spool, or spin the turbine wheel. The turbine wheel is connected to the compressor wheel via a common shaft. The compressor wheel compresses the intake charge increasing the charge density by a large factor.

The amount of time that it takes a turbocharger to reach the onset of boost is referred to as lag. A supercharger is 'on' all of the time, meaning that it is capable of producing a linear increase of boost up until redline. It is easier to target a desired boost with a turbocharger as there are many forms of boost controllers that allow a user to adjust to desired boost fairly easily. In order to achieve desired boost with a supercharger, a larger or smaller pulley must be installed.

Because a supercharger pump is driven by a pulley on the engine, the supercharger charge pressure is linearly proportionate to engine RPM. In other words, at 1/2 of peak RPM, a traditional supercharger only produces half of its peak boost. On the contrary, a turbocharger can be set up to produce near-peak boost levels at lower RPMs, which produces considerably more torque in an application. Emerging supercharger technologies are using techniques such as allowing internal viscosity to control a maximum pump output. This is advantageous because the supercharger can be set to reach peak boost at the onset of slip. Therefore, the linear power increase happens sooner, and the supercharger can be set to boost at higher pressure levels throughout the entire engine speed range. At present, however, for a given size, a turbocharger can usually be set to produce more power under the curve than an equivalent supercharger, but superchargers do not suffer from boost lag.

Intercooling

An unavoidable side-effect of forced induction is that compressing air raises its temperature (see also Combined gas law). As a result, the charge density is reduced and the cylinders receive less fresh air than the system’s boost pressure prescribes. The risk of detonation, or "knock" in internal combustion engines greatly increases. These drawbacks are countered by charge-air cooling, which passes the air leaving the turbocharger or supercharger through a heat exchanger typically called an intercooler. This is done by cooling the charge air with an ambient flow of either air (air-air intercoolers) or liquid (liquid to air intercoolers). The charge air density is increased and the temperature is reduced.

Water Injection

Water injection is another effective means of cooling the charge air to prevent detonation. Methanol is mixed with the water to prevent freezing and to act as a slower-burning fuel. Water injection, unlike nitrous oxide or forced induction itself, doesn't add more oxygen to the charge, but absorbs heat as it evaporates to cool the charge and lower combustion temperatures. The alcohol is also a fuel in the charge which burns slower and cooler than gasoline. Due to the lower intake temperatures and denser air charge more power is exerted from the engine. Water injection is typically used in conjunction with low-octane fuel in order to run higher than normal manifold pressures.

ee also

*supercharger
*turbocharger
*internal combustion engine

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • forced-induction system — A system in which either a conventional supercharger or a turbocharger, or even a combination of both, is used to increase intake pressure and force the mixture into the cylinders. Compare naturally aspirated engine …   Dictionary of automotive terms

  • Induction — Most common meanings * Inductive reasoning, used in science and the scientific method * Mathematical induction, a method of proof in the field of mathematics * Electromagnetic induction in physics and engineering Other articles * Induction (play) …   Wikipedia

  • Induction heating — is the process of heating an electrically conducting object (usually a metal) by electromagnetic induction, where eddy currents are generated within the metal and resistance leads to Joule heating of the metal. An induction heater (for any… …   Wikipedia

  • Induction (birth) — Induction is a method of artificially or prematurely stimulating labour in a woman. [ Houghton Mifflin Company, (2006): The American Heritage Dictionary. ] Common causes for induction include: * The baby is believed to be getting too big. *… …   Wikipedia

  • Sleep induction — Sleep induction, the deliberate effort to bring on sleep by various techniques or medicinal means, is practiced to lengthen periods of sleep, increase the effectiveness of sleep, and to reduce or prevent insomnia. Contents 1 Alcohol 2 Guided… …   Wikipedia

  • Intercooler — For the Australian rock group, see Intercooler (band). An intercooler (original UK term, sometimes aftercooler in US practice), or charge air cooler, is an air to air or air to liquid heat exchange device used on turbocharged and supercharged… …   Wikipedia

  • List of automotive superlatives — This page lists of the automobile industry that is, the smallest, largest, fastest, lightest, best selling, and other such topics.In order to keep the entries relevant, the list (except for the Firsts section) will be limited to automobiles built …   Wikipedia

  • Turbocharger — A turbocharger, or turbo, is an air compressor used for forced induction of an internal combustion engine. Like a supercharger, the purpose of a turbocharger is to increase the mass of air entering the engine to create more power. However, a… …   Wikipedia

  • Twincharger — refers to a forced induction system used on some piston type internal combustion engines. It is a combination of an exhaust driven turbocharger and a drive train driven supercharger, each mitigating the weaknesses of the other. Any forced… …   Wikipedia

  • Naturally aspirated engine — A naturally aspirated engine is one common type of reciprocating piston internal combustion engine that depends solely on atmospheric pressure to counter the partial vacuum in the induction tract to draw in combustion air. This is in contrast to… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”