Circuit diagram

Circuit diagram
Comparison of pictorial and schematic styles of circuit diagrams
Common schematic diagram symbols (US symbols)
The circuit diagram for a four-bit TTL counter, a type of state machine

A circuit diagram (also known as an electrical diagram, elementary diagram, or electronic schematic) is a simplified conventional graphical representation of an electrical circuit. A pictorial circuit diagram uses simple images of components, while a schematic diagram shows the components of the circuit as simplified standard symbols; both types show the connections between the devices, including power and signal connections. Arrangement of the components interconnections on the diagram does not correspond to their physical locations in the finished device.[1]

Unlike a block diagram or layout diagram, a circuit diagram shows the actual wire connections being used. The diagram does not show the physical arrangement of components. A drawing meant to depict what the physical arrangement of the wires and the components they connect is called "artwork" or "layout" or the "physical design."

Circuit diagrams are used for the design (circuit design), construction (such as PCB layout), and maintenance of electrical and electronic equipment.

Contents

Symbols

Circuit diagram symbols have differed from country to country and have changed over time, but are now to a large extent internationally standardized. Simple components often had symbols intended to represent some feature of the physical construction of the device. For example, the symbol for a resistor shown here dates back to the days when that component was made from a long piece of wire wrapped in such a manner as to not produce inductance, which would have made it a coil. These wirewound resistors are now used only in high-power applications, smaller resistors being cast from carbon composition (a mixture of carbon and filler) or fabricated as an insulating tube or chip coated with a metal film. The internationally standardized symbol for a resistor is therefore now simplified to an oblong, sometimes with the value in ohms written inside, instead of the zig-zag symbol. A less common symbol is simply a series of peaks on one side of the line representing the conductor, rather than back-and-forth as shown here.

Schematic wire junctions:
1. Old style: (a) connection, (b) no connection.
2. One CAD style: (a) connection, (b) no connection.
3. Recommended CAD Style: (a) connection, (b) no connection.

The linkages between leads were once simple crossings of lines; one wire insulated from and "jumping over" another was indicated by it making a little semicircle over the other line. With the arrival of computerized drafting, a connection of two intersecting wires was shown by a crossing with a dot or "blob", and a crossover of insulated wires by a simple crossing without a dot. However, there was a danger of confusing these two representations if the dot was drawn too small or omitted. Modern practice is to avoid using the "crossover with dot" symbol, and to draw the wires meeting at two points instead of one.[2][3][4] It is also common to use a hybrid style, showing connections as a cross with a dot while insulated crossings use the semicircle.

On a circuit diagram, the symbols for components are labelled with a descriptor or reference designator matching that on the list of parts. For example, C1 is the first capacitor, L1 is the first inductor, Q1 is the first transistor, and R1 is the first resistor (note that this is not written as a subscript, as in R1, L1,…). Often the value or type designation of the component is given on the diagram beside the part, but detailed specifications would go on the parts list.

Detailed rules for reference designations are provided in the International standard IEC 61346.

Organization of drawings

It is a usual although not universal convention that schematic drawings are organized on the page from left to right and top to bottom in the same sequence as the flow of the main signal or power path. For example, a schematic for a radio receiver might start with the antenna input at the left of the page and end with the loudspeaker at the right. Positive power supply connections for each stage would be shown towards the top of the page, with grounds, negative supplies, or other return paths towards the bottom. Schematic drawings intended for maintenance may have the principle signal paths highlighted to assist in understanding the signal flow through the circuit. More complex devices have multi-page schematics and must rely on cross-reference symbols to show the flow of signals between the different sheets of the drawing.

Detailed rules for the preparation of circuit diagrams (and other document kinds used in electrotechnology) are provided in the International standard IEC 61082-1.

Relay logic line diagrams (also called ladder logic diagrams) use another common standardized convention for organizing schematic drawings, with a vertical power supply "rail" on the left and another on the right, and components strung between them like the rungs of a ladder.

Artwork

A rat's nest

Once the schematic has been made, it is converted into a layout that can be fabricated onto a printed circuit board (PCB). The layout is usually started by the process of schematic capture. The result is what is known as a rat's nest. The rat's nest is a jumble of wires (lines) criss-crossing each other to their destination nodes. These wires are routed either manually or by the use of electronics design automation (EDA) tools. The EDA tools arrange and rearrange the placement of components and find paths for tracks to connect various nodes. This results in the final layout artwork for the integrated circuit or printed circuit board.[5]

A generalized design flow would be as:

Schematic → Schematic capture → Rat's nest → Routing → Artwork → PCB development & etching → Component mounting → Testing

See also

  • DipTrace – Schematic Capture and PCB design software
  • Edwinxp – Totally Integrated Schematic Capture, Simulation Software and PCB design
  • Electronic symbol
  • gEDA – GNU EDA-Tool used for schematic circuit design
  • Kicad – GPL-ed EDA-Tool used for schematic circuit and PCB design
  • Multisim Electronic schematic capture and simulation software
  • OrCAD or Eagle (program) – Software for electronic schematics and for the design of printed circuit boards.
  • Schematic capture
  • Schematic editor
  • Wiring diagram
  • The schematic typically shows the pinout of each part.

References

  1. ^ Circuit diagrams and component layouts
  2. ^ "We recommend against using a 4-way connection point ... To avoid confusion, use only three-way connections." -- "Design News Gadget Freak Submission Guidelines"
  3. ^ "Wires connected at 'crossroads' should be staggered slightly to form two T-junctions" -- "The Electronics Club: Circuit Symbols"
  4. ^ "It is good practice to never use a + connection with a dot. Why? The dot can disappear when the schematic is copied for the 12th time." -- "Notes on Reading Schematics"
  5. ^ R. S. Khandpur (2005). Printed circuit boards: design, fabrication, assembly and testing. Tata McGraw-Hill. p. 10. ISBN 9780070588141. http://books.google.com/books?id=m8sJBIMtETgC&pg=PA10&dq=circuit-diagram+artwork#v=onepage&q=circuit-diagram%20artwork&f=false. 

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • circuit diagram — sujungimų schema statusas T sritis automatika atitikmenys: angl. circuit diagram; connection diagram; routing pattern vok. Schaltbild, n; Schaltschema, n; Schaltskizze, n; Stromlaufschema, n rus. рисунок соединений, m; схема соединений, f pranc.… …   Automatikos terminų žodynas

  • circuit diagram — grandinės schema statusas T sritis automatika atitikmenys: angl. circuit diagram vok. Schaltungsmuster, n rus. рисунок схемы, m pranc. dessin du circuit, m …   Automatikos terminų žodynas

  • circuit diagram — A wiring diagram showing the path of the electrical connections and the various colors of the wires …   Dictionary of automotive terms

  • schematic circuit diagram — sujungimo schema statusas T sritis fizika atitikmenys: angl. connection diagram; schematic circuit diagram vok. Schaltplan, m; Schaltungsschema, n rus. схема соединения, f pranc. schéma de montage, m; schéma des connexions, m …   Fizikos terminų žodynas

  • cable circuit diagram — kabelių išdėstymo schema statusas T sritis automatika atitikmenys: angl. cable arrangement; cable circuit diagram vok. Kabelplan, m rus. схема расположения кабелей, f pranc. plan de câblage, m …   Automatikos terminų žodynas

  • Circuit — may mean: In science and technology Circuit theory, the theory of accomplishing work by routing electrons, gas, fluids, or other matter through a loop Pneumatic circuit Hydraulic circuit Boolean circuit circuit (computer theory) Integer circuit a …   Wikipedia

  • Circuit design — The process of circuit design can cover systems ranging from complex electronic systems all the way down to the individual transistors within an integrated circuit. For simple circuits the design process can often be done by one person without… …   Wikipedia

  • Diagram — Further information: Chart Sample flowchart representing the decision process to add a new article to Wikipedia. A diagram is a two dimensional geometric symbolic representation of information according to some visualization technique. Sometimes …   Wikipedia

  • Circuit theory — For the theory of monetary economics, see monetary circuit theory. Circuit theory is the theory of accomplishing work by means of routing matter through a loop.[citation needed] The types of matter used are: In electronic or electrical circuits:… …   Wikipedia

  • Circuit de Monaco — Coordinates: 43°44′5″N 7°25′14″E / 43.73472°N 7.42056°E / 43.73472; 7.42056 …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”