Modular connector

Modular connector
Left to right, modular connectors: 8P8C plug, 6P6C plug, 6P4C plug, 4P4C plug, 6P6C jack.
An 8P8C modular plug. This is the common crimp type plug, of the same kind pictured above crimped onto a cable (with moulded sleeve)

Modular connector is the name given to a family of electrical connectors originally used in telephone wiring and now used for many other purposes. Many applications that originally used a bulkier, more expensive connector have now migrated to modular connectors. Probably the most well known applications of modular connectors are for telephone jacks and for Ethernet jacks, both of which are nearly always modular connectors.

Modular connectors were originally used with the registered jack system, which precisely describes how the connectors are wired for telecommunications. The registered jack specifications define the wiring patterns of the jacks, not the physical dimensions or geometry of the connectors of either gender. Instead, these latter aspects are covered by ISO standard 8877, first used in ISDN systems. TIA/EIA-568 is a standard for data circuits wired on modular connectors.

Other systems exist for assigning signals to modular connectors; physical interchangeability of plugs and jacks does not ensure interoperation, nor protection from electrical damage to circuits. For example, modular cables and connectors have been used to supply low-voltage AC or DC power, and no clear standard exists for this application.

Contents

Nomenclature

Modular connectors also go by the names "modular phone jack/plug", "RJ connector," and "Western jack/plug." The term "modular connector" arose from its original use in a novel system of cabling designed to make telephone equipment more modular. This includes the 4P4C handset connector which is sometimes called an "RJ9" or an "RJ22" — but such RJ specifications are absent in the current FCC documents.[1][2][3]

It is very common, but incorrect, to use a registered jack number to refer to the physical connector itself; for instance, the 8P8C modular connector type is often loosely called RJ45 (after a telephone company standard that uses a similar connector), but 8P8C connectors are also used with different signals, such as for Ethernet over twisted pair.

History

Modular connectors were originally patented by Bell Telephone Laboratories in 1975. [4] They replaced the hard-wired connections on most Western Electric telephones around 1976. At the same time, they began to replace screw terminals and larger 3 and 4 pin telephone jacks in buildings.

Gender

Modular connectors have gender: male connectors are called plugs, while female connectors are called jacks or, sometimes, sockets.

Plugs are used to terminate loose cables and cords, while jacks are used for fixed locations on surfaces such as walls and panels, and on equipment. Other than telephone extension cables, cables with a modular plug on one end and a jack on the other are rare. Instead, cables are connected using a male-to-male adapter, which consists of two female jacks wired back-to-back.

Latching tab and orientation

Modular connectors are designed to latch together. A spring-loaded tab on the plug snaps into a jack so that the plug cannot be pulled out. To remove the plug, the latching tab must be depressed. The most common way to install a jack in a wall or panel is with the tab side down. This usually makes it easier to operate the tab when removing the plug, because the person grabs the plug with thumb on top and presses the tab with the index finger. This orientation is also preferred because any dust or fine abrasive or conductive particles that may enter an unused jack will tend to fall away from the electrical contacts, rather than settling onto the contact surfaces.

The modular connector suffers from a design flaw however, as the fragile tab easily snags on other cables and breaks. When this happens, the connector is still functional, but the crucial latching feature is lost. Some higher quality cables have a flexible sleeve called a "boot" over the plug, or a special tab design, to prevent this. These cables are often marketed as snagless. Boots are seen mainly on 8P8C data cables, but are also used on other sizes of connectors.

Sizes and contacts

8P8C modular plug pin numbering
8P8C plug with contacts for solid wire (left) and stranded wire (right)
contacts for solid wire (top left) and stranded wire (bottom right)

Modular connectors come in four sizes: 4-, 6-, 8-, and 10-position, where a position is a location for a contact. Not all of the positions may have contacts installed. When contacts are omitted, they are typically done so from the outermost pair of contacts inward, such that the number of contacts is almost always an even number. The insulating plastic bodies of 4P and 6P connectors have different widths, whereas 8P or 10P connectors share an even larger body width. The connector body positions with omitted contacts or contacts unattached to wires are unused for the electrical connection, but ensure that the plug fits correctly. For instance, RJ11 cables often have connectors with 6 positions and 4 contacts, to which are attached just 2 wires.

The connectors are designated with two numbers that represent the quantity of positions and contacts, with each number followed by a "P" and "C", respectively: for example, "6P2C" for a connector having 6 positions and 2 contacts. Alternate designations omit the "P" and "C" while separating the position and contact quantities with either an "x" ("6x2") or a slash ("6/2").

Internally, the contacts have sharp prongs that when crimped, pierce the insulation and connect with the wire conductor, a mechanism known as insulation displacement. Ethernet cables, in particular, may have solid or stranded wire conductors and the sharp prongs are different in the 8P8C connectors made for each type of wire. A modular plug for solid (single strand) wire often has three slightly splayed prongs on each contact to securely surround and grip the conductor. Modular plugs for stranded or tinsel wire have prongs that are designed to connect to multiple wire strands. Connector plugs are designed for either solid or stranded wire; a plug for one wire type might not make reliable contact when crimped to a cable with wires of the other type.

The dimensions of the connectors are such that a plug can be inserted into a jack that has more positions than the plug, leaving the jack's outermost contacts unconnected. However, not all plugs from all manufacturers have this capability, and some jack manufacturers warn that their jacks are not designed to accept smaller plugs without damage. If an inserted plug lacks contact slots at the outermost extremes, it may permanently deform the outmost contacts of an incompatible jack.

The contact positions are numbered sequentially starting from 1. When viewed head-on with the retention mechanism on the bottom, jacks will have contact position number 1 on the left and plugs will have it on the right. Contacts are numbered by the contact position. For example, on a 6-position, 2-contact plug, where the outermost four positions do not have contacts, the innermost two contacts are numbered 3 and 4.

Some modular connectors are indexed: their dimensions are intentionally non-standard, preventing connections with connectors of standard dimensions. The means of indexing may be non-standard cross-section dimensions or shapes, retention mechanism dimensions, or retention mechanism quantity. For example, a Modified Modular Jack (MMJ) using an offset latching tab was developed by Digital Equipment Corporation (DEC) to prevent accidental interchange of data and telephone cables.

Termination

Termination of modular connector cables is very similar, regardless of the number of positions and contacts in the plug. To prevent damage to the plug (and the expensive crimp die-set), the crimp tool must be carefully matched to the plug being attached. For example, termination of a cable with an 8P8C plug involves using a hand crimper or crimp machine containing an 8P8C die-set or an A67T[citation needed] standard die-set. An 8P8C crimp die-set usually looks similar to an 8P8C jack, except for the eight teeth lining the top portion of the die. When the tool is operated, the die compresses around the 8P8C plug. As the die compresses, these teeth force the plug contacts down into the conductors of the cable being terminated, permanently attaching the plug to the cable.

There are two sub-types of plug, that differ only in the type of contacts used. One contact is suitable for solid (single strand) copper conductors and the other is suitable for stranded or tinsel wire copper conductors. The crimper may also permanently deform part of the plastic plug body in such a way that it grips the outer sheath of the cable. This helps to keep the plug securely fastened to the end of the cable, by providing strain relief.

Pinouts

Contact assignments, or pinouts, vary by application. Telephone network connections are standardized by registered jack numbers, and Ethernet over twisted pair is specified by the TIA/EIA-568-B standard. Other applications have no standardization; for example, there are multiple conventions for use of 8P8C connectors for RS-232.

For this reason, D-sub-to-modular adapters are typically shipped with the D-sub contacts (pins or sockets) terminated but not inserted into the connector body, so that the D-sub-to-modular contact pairing can—and must—be performed by the end-user.

4P4C

4P4C modular connector on a handset cable
Wired telephone using 4P4C connectors

The 4P4C connector, is popularly, but incorrectly, called RJ22, RJ10, or RJ9. It is also commonly referred to as a "Handset Connector" because of the most popular usage for the connector.[5] It is the de facto industry standard for wired telephone handsets. It is used to provide connection from the base of the telephone to the handset.

This handset connector is actually not a registered jack at all, since it was never intended to connect directly to the telephone service lines: RJ connects a phone to the service lines, while 4P4C connects two parts of a phone. Other RJ connector wiring standards are used by telephone companies. The 4P4C is only used for an end user application from the phone to the handset.

Wiring

Wiring diagram for handset use of 4P4C/RJ9 plug

The straight-through wiring method shown in the diagram is used. The handset's speaker (the transducer) functions normally, even though its polarity is reversed; but the electret microphone used in most modern handsets will not function normally if it is reverse connected. However, if the wire pair for the handset transducer and the wire pair for the handset microphone are each wired in a crossover arrangement, then both the transducer and microphone will function correctly; even if the handset has an electret microphone. Most telephone handset cords (cable assemblies) are wired this way.[6]

Old handsets made before 1985 use a carbon microphone which is not sensitive to polarity.

Data port

The Macintosh 128K, Macintosh 512K and Macintosh Plus from Apple used 4P4C connectors to connect the keyboard to the main computer housing. The connector provided power to the keyboard on the outer two conductors and received data signals on the inner pair. The cable between the computer and the keyboard was a coiled cord with an appearance very similar to a telephone handset cable.[7] The connector wiring, however, required a polarized straight through pinout. Using a telephone handset cable instead of the supplied cable could short out the +5 volt DC supply and damage the computer or the keyboard.[8]

Some consumer equipment such as DirecTV set top boxes include a 4P4C low-speed data port connector.[6] Such connectors can be adapted for use with a computer's serial port so that control commands can be sent from the computer to the set top box.

6P6C

6P4C crimp-on style connector

The 6P2C, 6P4C, and 6P6C modular connectors are probably most well known for their use as RJ11, RJ14, and RJ25 registered jacks respectively.

RJ11 is a physical interface often used for terminating telephone wires. It is probably the most familiar of the registered jacks, being used for single line POTS telephone jacks in most homes across the world.

RJ14 is similar, but for two lines, and RJ25 is for three lines. RJ61 is a similar registered jack for four lines. The telephone line cord and its plug are more often a true RJ11 with only two conductors.

Modular plugs are described as containing a number of potential contact "positions" and the actual number of contacts installed within these positions. RJ11, RJ14, and RJ25 all use the same six-position modular connector, thus are physically identical except for the different number of contacts (two, four and six respectively).

RJ11 wiring

6P6C connector showing the location of pin 1

Cables sold as RJ11 often actually use 6P4C RJ14 connectors (six position, four conductor), with four wires running to a central junction box. Two of its six possible contact positions connect tip and ring, and the other two conductors are then unused. 6P2C and 6P6C can also be found in stores.

The conductors other than the two central tip and ring conductors are in practice used for various things such as a ground for selective ringers, low voltage power for a dial light, or for 'anti-tinkle' circuitry to prevent pulse dialing phones from ringing the bell on other extensions. With tone dialing, anti-tinkle measures are not required.

Pinouts

Holding the connector in your hand tab side down with the cable opening toward you, the pins are numbered 1–6, left to right.

Position Pair T/R ± RJ11 RJ14 RJ25 Twisted pair colors 25-pair colors Old colors[a] German colors[b] Australian colors
1 3 T + T3 Pair 3 Wire 1 Cat 5e/6
white/green
Pair 4 Wire 1
white/green
Pair 3 wire 1
white
Pair 3 wire 1
pink
Pair 3 wire 1
orange
2 2 T + T2 T2 Pair 2 Wire 1 Cat 5e/6
white/orange
Pair 2 Wire 1
white/orange
Pair 2 Wire 1 Old
black
Pair 2 ext. bell
green
Pair 2 ext. bell
red
3 1 R - R1 R1 R1 Pair 3 Wire 2 Cat 5e/6
blue
Pair 1 Wire 2
blue/white
Pair 1 Wire 2 Old
red
Pair 1 wire A
white
Pair 1 wire B
blue
4 1 T + T1 T1 T1 Pair 1 Wire 1 Cat 5e/6
white/blue
Pair 1 Wire 1
white/blue
Pair 1 Wire 1 Old
green
Pair 1 wire B
brown
Pair 1 wire A
white
5 2 R - R2 R2 Pair 3 Wire 1 Cat 5e
orange
Pair 2 Wire 2
orange/white
Pair 2 Wire 2 Old
yellow
Pair 2 ground
yellow
Pair 2 ground
black
6 3 R - R3 Pair 1 Wire 1 Cat 5e
green
Pair 3 Wire 2
green/white
Pair 3 Wire 2
blue
Pair 3 wire 2
gray
Pair 1 Wire 1 Old
green
  • ^[a] While the old solid color code was well established for pair 1 and usually pair 2, there are several conflicting conventions for pair 3 (and sometimes even pair 2). The colors shown above were taken from a vendor of "silver satin" flat 8-conductor phone cable that claims to be standard. 6-pair solid (old) bellwire cables previously used by the Bell System use white for pair 3 tip but some vendor's cable may substitute orange for white. At least one other vendor of flat 8-conductor cable uses the sequence blue, orange, black, red, green, yellow, brown and white/slate.
  • ^[b] This color scheme originates in the (withdrawn) national standard DIN 47100. The scheme shown here is the correct color code for interfacing with the RJ connector standards.

However, with German domestic telephone equipment (and that in some neighbouring countries), 6P4C plugs and sockets are typically only used to connect the telephone cable to the phone base unit, whereas the mechanically different TAE plug is used at the other end of the cable. Older base units may accommodate the additional connectors of TAE (E, W, a2, b2) and may feature non-RJ standard sockets that can be connected „straight“ to TAE plugs. Further, flat DIN 47100 cables typically place the wires in ascending order. When used directly with 6P4C plugs, the colors will be scrambled.

Powered version of RJ11

In the powered version, Pins 2 and 5 (black and yellow) may carry low voltage AC or DC power. While the phone line itself (tip and ring) supplies enough power for most telephone terminals, old telephone terminals with incandescent lights in them (such as the classic Western Electric Princess and Trimline telephones) need more power than the phone line can supply. Typically, the power on Pins 2 and 5 comes from a transformer plugged into a wall near one jack, supplying power to all of the jacks in the house. Trimline and Princess phone dial lights are rated at 6.3 volts and the transformer output is typically around 5 volts, providing a long service life for the incandescent lamps.

Compatibility with structured cabling

With the rise of Ethernet local area networks operating over Cat5e and Cat6 unshielded twisted pair cable, structured cabling networks adhering to TIA/EIA-568-B, ISO/IEC 11801 or ISO/IEC 15018 (home networks) are widely used for both computer networking and analog telephony, but these standards specify the T568-A or T568-B pin-outs compatible with Ethernet. The 8P8C ("RJ45") jack used by structured cabling physically accepts the 6-position connector used by RJ11, RJ14 and RJ25, but only RJ11 and RJ14 have full electrical compatibility. Ethernet compatible pin-outs "split" the third pair of RJ25 across two separate cable pairs, rendering it unusable by analog phones. This was necessary to preserve the electrical properties of those pairs for Ethernet, which operates at much higher frequencies than analog telephony.

Both the third and fourth pairs of RJ61 are similarly split. Because of this incompatibility, and because they were never very common to begin with, the TIA/EIA-568-B conventions are displacing RJ25 and RJ61 for telephones with more than two lines.

8P8C

An 8P8C modular plug before being crimped onto a cable
Connector and cable

The 8P8C (8 Position 8 Contact, also backronymed as 8 position 8 conductor; [9]) is a modular connector commonly used to terminate twisted pair and multiconductor flat cable. These connectors are commonly used for Ethernet over twisted pair, registered jacks and other telephone applications, RS-232 serial using the EIA/TIA 561 and Yost standards, and other applications involving unshielded twisted pair, shielded twisted pair, and multiconductor flat cable.

An 8P8C modular connector has two paired components: the male plug and the female jack, each with eight equally-spaced conducting channels. On the plug, these conductors are flat contacts positioned parallel with the connector body. Inside the jack, the conductors are suspended diagonally toward the insertion interface. When an 8P8C plug is mated with an 8P8C jack, the conductors meet and create an electrical connection. Spring tension in the jack's conductors ensures a good interface with the plug and allows for slight travel during insertion and removal.

Although commonly referred to as an RJ45[10] in the context of Ethernet and category 5 cables,[11][12] it is incorrect to refer to a generic 8P8C connector as an RJ45. A telephone-system-standard RJ45 socket has a key which excludes insertion of an un-keyed 8P8C plug. [13] The registered jack (RJ) standard specifies a different mechanical interface and wiring scheme for a RJ45S than TIA/EIA-568-B which is often used for modular connectors used in Ethernet and telephone applications. 8P8C modular plugs and jacks look very similar to the plugs and jacks used for FCC's registered jack RJ45 variants, although the RJ45S is not compatible with 8P8C modular connectors.

The original RJ45S used a [14][15] keyed 8P2C modular connector, with Pins 5 and 4 (the middle 2 positions) wired for tip and ring of a single telephone line and Pins 7 and 8 shorting a programming resistor. It was meant to be used with a high speed modem, and is obsolete today.

Telephone installers who wired RJ45S modem jacks or RJ61X telephone jacks were familiar with the pin assignments that were part of the standard. However, the standard un-keyed modular connectors became ubiquitous for computer networking, and informally inherited the name "RJ45". While RJ45S uses a "keyed" variety of the 8P body, meaning it may have an extra tab that a common modular connector is unable to mate with, the visual difference is subtle and likely caused the confusion.

Understandably, because telephone RJ61 and data RJ45/RJ48 connectors never saw wide usage and computer 8P8C connectors are quite well known today, "RJ45" is used to refer to 8P8C, un-keyed modular connectors with Ethernet-type wiring pin-outs. Electronics catalogs commonly advertise 8P8C modular connectors as "RJ45", many electronic equipment manuals using an 8P8C connector will document it as an "RJ45" connector. In common usage, RJ45 may also refer to the pin assignments for the attached cable, which are actually defined as T568A and T568B in wiring standards such as TIA/EIA-568-B.

Standardization

The shape and dimensions of an 8P8C modular connector are specified for U.S. telephone applications by the Administrative Council for Terminal Attachment (ACTA) in national standard ANSI/TIA-1096-A. This standard does not use the short term 8P8C and covers more than just 8P8C modular connectors, but the 8P8C modular connector type is the eight position connector type described therein, with eight conductors installed. The international standard is ISO-8877.

For data communication applications (LAN, structured cabling), International Standard IEC 60603 specifies in parts 7-1, 7-2, 7-4, 7-5, and 7-7 not only the same physical dimensions, but also high-frequency performance requirements for shielded and unshielded versions of this connector for frequencies up to 100, 250 and 600 MHz, respectively.

Wiring

T568A wiring
T568B wiring

Connectors are frequently terminated using the T568A or T568B pin/pair assignments that are defined in TIA/EIA-568-B. A cable that is wired as T568A at one end and T568B at the other (Tx and Rx pairs reversed) is a "crossover" cable. Before the widespread acceptance of auto-MDI/MDIX capabilities a crossover cable was needed to interconnect similar network equipment (such as hubs to hubs). A cable wired the same at both ends is called a "patch" or "straight-through" cable, because no pin/pair assignments are swapped. Crossover cables are sometimes still used today to connect two computers together without a switch or hub, however most Network Interface Cards (NIC) in use today are called smart, because they automatically configure themselves based on the type of cable plugged into them. If a "patch" or "straight" cable is used, to connect two computers with "smart" NICs, the NIC will configure itself to switch the Tx and Rx.

Types

Two types of 8P8C plugs and installation tools (used for crimping the plug onto a cable) are commonly available: Western Electric/Stewart Stamping (WE/SS) and Tyco/AMP. While both types look remarkably similar, the tooling used to install the two different plug types is mutually exclusive and cannot be interchanged between the two types. WE/SS compatible plugs are available from a large number of manufacturers, whereas Tyco/AMP plugs are produced exclusively by Tyco Electronics. Both types of modular plugs will plug into the same standard 8P8C modular jack.

WE/SS and Tyco/AMP 8P8C plugs have different spacing for the cable strain relief.[16][17] As a result, using a WE/SS 8P8C crimp dieset on a Tyco/AMP 8P8C plug will crush the top of the connector and damage the crimp dieset, and vice versa. While the WE/SS compatible plug is produced by a larger number of manufacturers than the Tyco/AMP plug, it is still important to know what style is being used to avoid damaging the plug or tool during crimping.

Both types of 8P8C plugs are available in shielded and unshielded varieties, depending on the attenuation tolerance needed. Shielded plugs are more expensive and require shielded cable, but have a lower attenuation and can reduce signal noise.

Applications

8P8C are commonly used in computer networking and telephone applications, where the plug on each end is an 8P8C modular plug wired according to a TIA/EIA standard. Most network communications today are carried over Category 5e or Category 6 cable with an 8P8C modular plug crimped on each end.

The 8P8C modular connector is also used for RS-232 serial interfaces according to the EIA/TIA-561 standard.[18] This application is commonly used as a console interface on network equipment such as switches and routers. Other applications include other networking services such as ISDN and T1.

In floodwired[19] environments the center (blue) pair is often used to carry telephony signals. Where so wired, the physical layout of the 8P8C modular jack allows for the insertion of an RJ11 plug in the center of the jack, provided the RJ11 plug is wired in true compliance with the U.S. telephony standards (RJ11) using the center pair. The formal approach to connect telephony equipment is the insertion of a type-approved converter.

The remaining (brown) pair is increasingly used for Power over Ethernet (PoE). Legacy equipment may use just this pair; this conflicts with other equipment as manufacturers used to short circuit unused pairs to reduce signal crosstalk.[citation needed] Some routers/bridges/switches can be powered by the unused 4 lines—blues (+) and browns (−)—to carry current to the unit. There is now a standardized scheme for Power over Ethernet]

Different manufacturers of 8P8C modular jacks arrange for the pins of the 8P8C modular connector jack to be linked to wire connectors (often IDC type terminals) that are in a different physical arrangement from that of other manufacturers: Thus, for example, if a technician is in the habit of connecting the white/orange wire to the "bottom right hand" IDC terminal, which links it to 8P8C modular connector pin 1, in jacks made by other manufacturers this terminal may instead connect to 8P8C modular connector pin 2 (or any other pin).

10P10C

The pin arrangement for a 10P10C socket

The 10P10C connector is commonly referred to as an RJ50 connector, although this is not a standard registered jack in the Universal Service Order Codes. The 10P10C has 10 contact position and 10 contacts.

Connector10p10c.jpg

The most common uses of the 10P10C connector are in proprietary data transfer systems,[20] such as the Digi International Digiboard serial connections.[21] It is also used to implement the RS-232 and RS-485 connector standards. It is also used in APC and Eaton uninterruptible power supplies. In this case, it is a keyed 10P10C plug with a protrusion on the pin 1 side near the back.

This connector is also used by some vendors such as BOCA, for expansion modules of their multi-port RS-232C serial boards. For example, Cyclades used the pin #1 as a "RI" (Ring Indicator) signal, which is rarely used, allowing an 8P8C connector to be plugged to their 10P10C socket for most applications. The Cisco Systems STS-10X terminal server featured this connector. FordNet, a five-pair communications networking medium also used the 10P10C between terminals.

See also

Notes

  1. ^ FCC 47 CFR Part 68 section 68.502 superseded by T1.TR5-1999
  2. ^ T1.TR5-1999 Network and Customer Installation Interface Connector Wiring Configuration Catalog at ATIS
  3. ^ ACTA documents
  4. ^ (patent filed 6 July 1973; U.S. Patent 3,860,316 issued 14 January 1975)
  5. ^ BICSI (October 7, 2002). "Background Information". Telecommunications Cabling Installation (2nd ed.). McGraw-Hill Professional. p. 88. ISBN 0-07-140979-3. "4-position and 4-contact connectors are used primarily for telephone handset cords." 
  6. ^ a b GBPVR Wiki. Direc TV Channel Control. "Each end of a handset cord is wired opposite the other..."
  7. ^ My Old Computers. Apple Macintosh Plus
  8. ^ Syrinx. Mac Plus Keyboard Cable. "...the cable is the same as the telephone cable that connects handsets to the phone, unfortunately [...] this type of cable and pretty much any type of pre manufactured cable [...] is wired wrong for the Mac Plus. Under no circumstances should you use this cable as you will damage your keyboard and/or your Mac!"
  9. ^ Trulove, James (December 19, 2005). "Designing LAN Wiring Systems". LAN wiring (3rd ed.). McGraw-Hill Professional. p. 23. ISBN 0-07-145975-8. "The 8-pin modular jack is sometimes referred to as an "RJ-45," because the connector/jack components are the same. However, RJ-45 actually applies to a special purpose jack configuration that is not used in LAN or standard telephone wiring." 
  10. ^ Trulove, James (December 19, 2005). "Work Area Outlets". LAN wiring (3rd ed.). McGraw-Hill Professional. p. 132. ISBN 0-07-145975-8. "Modular jacks are often referred to as "RJ-45" jacks. This is not really the correct moniker, although it is in very common use." 
  11. ^ Oliviero, Andrew; Woodward, Bill (July 20, 2009). "Connectors". Cabling: The Complete Guide to Copper and Fiber-Optic Networking (4th ed.). Sybex. p. 294. ISBN 0-470-47707-5. "The RJ (registered jack) prefix is one of the most widely (and incorrectly) used prefixes in the computer industry; nearly everyone, including people working for cabling companies, is guilty of referring to an eight-position modular jack (sometimes called an 8P8C) as an RJ-45." 
  12. ^ Semenov, Andrey B.; Strizhakov, Stanislav K.; Suncheley, Igor R. (October 3, 2002). "Electrical Cable Connectors". Structured cable systems (1st ed.). Springer. p. 129. ISBN 3-540-43000-8. "The traditional 8-contact connector, which is called Western Plug, 8PMJ (8-position modular jack), 8P8C (8 position 8 conductor), or somewhat incorrectly RJ-45, is used widely in SCS practice." 
  13. ^ Trulove, James (December 19, 2005). "User Cords and Connectors". LAN wiring (3rd ed.). McGraw-Hill Professional. p. 219. ISBN 0-07-145975-8. "This 8-pin modular plug is probably the most subject to name abuse, because it resembles the specialized RJ-45 connector. However, the RJ-45 wiring pattern (which includes an interface programming resistor) is so radically different from that of T568A and B that it really should not be called by that name at all." 
  14. ^ , Ontario, CA: HVS, http://www.hvs.on.ca/modular_jack_wiring.htm 
  15. ^ Modular wiring reference, Siemon, http://www.siemon.com/us/standards/13-24_modular_wiring_reference.asp 
  16. ^ "Stewart Connector 937-SP-3088 - Eight conductor/eight position line cord module" (PDF). Glen Rock, Pennsylvania: Bel Stewart Connector. 2006-02-01. http://www.belfuse.com/Data/Datasheets/CT300064.pdf. Retrieved 2009-09-10. 
  17. ^ "Tyco/AMP 5-554739-2 - Modular plug assembly, 8 position, flat oval cable" (PDF). Harrisburg, Pennsylvania: Tyco Electronics Corporation. 2008-03-31. http://www.tycoelectronics.com/commerce/DocumentDelivery/DDEController?Action=showdoc&DocId=Customer+Drawing%7F554739%7FP%7Fpdf%7FEnglish%7FENG_CD_554739_P.pdf. Retrieved 2009-09-10. 
  18. ^ http://www.zytrax.com/tech/layer_1/cables/tech_rs232.htm#rj45
  19. ^ floodwire is a chiefly British term for installing communications cables in a massive fashion in anticipation of their eventual use.
  20. ^ 10 pin RJ50 (10P10C) male connector diagram and applications
  21. ^ Digi PortServer TS 10P10C (RJ50) Modular RS-232 pinout

References

  • ANSI/TIA-968-A: Telephone terminal equipment: Technical requirements for connection of terminal equipment to the telephone network
  • IEC 60603-7-1: Connectors for electronic equipment: Part 7-1: Detail specification for 8-way, shielded free and fixed connectors with common mating features, with assessed quality
  • IEC 60603-7-2: Connectors for electronic equipment: Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz
  • IEC 60603-7-4: Connectors for electronic equipment: Part 7-4: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
  • IEC 60603-7-5: Connectors for electronic equipment: Part 7-5: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
  • IEC 60603-7-7: Connectors for electronic equipment: Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 600 MHz
  • ISO/IEC 8877, EN 28877: Information Technology—Telecommunications and Information Exchange between Systems—Interface Connector and Contact Assignments for ISDN Basic Access Interface Located at Reference Points S and T
  • Registered Jack references are US government documents that define modular connectors for telecommunications. (Note: 4P4C and 10P10C connectors are NOT defined in these standards.)

Further reading

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • modular connector — F/A/V connector used with 4, 6, or 8 pins. Common modular connectors are RJ 11 and RJ 45 …   Audio and video glossary

  • Modular power supply unit — A modular power supply to the left and a non modular power supply to the right. A modular power supply unit, abbreviated MPS, is a type of computer power supply with cables to powered devices attached by removable power connectors instead of… …   Wikipedia

  • Modular Power Supply Unit — A Modular Power Supply Unit, or MPS , is a term for a computer s power supply in which the user can choose which of the detachable power connectors to install between the computer s components and the computer power supply.Many modular power… …   Wikipedia

  • 600 series connector — A 600 series connector is an obsolete three pin connector with up to six conductors. It was for many years the standard telephone service (POTS) connector in Australia, but has now been replaced by the six position modular connector in this… …   Wikipedia

  • Electrical connector — Back of an audio amplifier features a variety of electrical connectors An electrical connector is an electro mechanical device for joining electrical circuits as an interface using a mechanical assembly. The connection may be temporary, as for… …   Wikipedia

  • Microphone connector — Contents 1 TRS connectors 2 XLR connectors 3 Multi pin Foster circular connectors …   Wikipedia

  • Modified Modular Jack — Modified Modular Jack …   Wikipedia

  • SDL connector — A Shielded Data Link connector is a type of electrical connector in which the signal pins are surrounded by a metal shield. The connector was designed by AMP (now Tyco) and is available with a range of pins (4 to 16), and features a locking… …   Wikipedia

  • Self-reconfiguring modular robot — Modular self reconfiguring robotic systems or self reconfigurable modular robots are autonomous kinematic machines with variable morphology. Beyond conventional actuation, sensing and control typically found in fixed morphology robots, self… …   Wikipedia

  • DC connector — A DC connector (or DC plug, for one common type of connector) is an electrical connector for supplying direct current (DC) power. Unlike domestic AC power plugs and sockets, DC connectors are not generally standardized. The dimensions and… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”