Ship model basin

Ship model basin
US Experimental Model Basin, circa 1900
The Ocean Towing Tank - with both towing and wave making facilities - at University College London
A model being tested in the Towing Tank of Newcastle University.
Cavitation tunnel of the Versuchsanstalt für Wasserbau und Schiffbau in Berlin
Cavitating propeller in a water tunnel experiment at the David Taylor Model Basin


A ship model basin may be defined as one of two separate yet related entities, namely:

  • a physical basin or tank used to carry out hydrodynamic tests with ship models, for the purpose of designing a new (full sized) ship, or refining the design of a ship to improve the ship's performance at sea;
  • the organization (often a company) that owns and operates such a facility.

In the second meaning, the company or authority is an engineering firm. that acts as a contractor to the relevant shipyards, and provides hydrodynamic model tests and numerical calculations to support the design and development of ships and offshore structures.

The hydrodynamic test facilities present at a model basin site include at least:

  • A towing tank: This is a basin, several metres wide and hundreds of metres long, equipped with a towing carriage that runs on two rails on either side. The towing carriage can either tow the model or follow the self-propelled model, and is equipped with computers and devices to register or control, respectively, variables such as speed, propeller thrust and torque, rudder angle etc. The towing tank serves for resistance and propulsion tests with towed and self-propelled ship models to determine how much power the engine will have to provide to achieve the speed laid down in the contract between shipyard and ship owner. The towing tank also serves to determine the maneuvering behaviour in model scale. For this, the self-propelled model is exposed to a series of zig-zag maneuvers at different rudder angle amplitudes. Post-processing of the test data by means of system identification results in a numerical model to simulate any other maneuver like Dieudonné spiral test or turning circles. Additionally, a towing tank can be equipped with a PMM (planar motion mechanism) or a CPMC (computerized planar motion carriage) to measure the hydrodynamic forces and moments on ships or submerged objects under the influence of oblique inflow and enforced motions. The towing tank can also be equipped with a wave generator to carry out seakeeping tests, either by simulating natural (irregular) waves or by exposing the model to a wave packet that yields a set of statistics known as response amplitude operators (acronym RAO), that determine the ship's likely real-life sea-going behavior when operating in seas with varying wave amplitudes and frequencies (these parameters being known as sea states). Modern seakeeping test facilities can determine these RAO statistics, with the aid of appropriate computer hardware and software, in a single test.
  • A cavitation tunnel to investigate propellers. This is a vertical water circuit with large diameter pipes. At the top, it carries the measuring facilities. A parallel inflow is established. With or without a ship model, the propeller, attached to a dynamometer, is brought into the inflow, and its thrust and torque is measured at different ratios of propeller speed (number of revolutions) to inflow velocity. A stroboscope synchronized with the propeller speed serves to visualize cavitation as if the cavitation bubble would not move. By this, one can observe if the propeller would be damaged by cavitation. To ensure similarity to the full-scale propeller, the pressure is lowered, and the gas content of the water is controlled.
  • Workshops: Ship model basins manufacture their ship models from wood or paraffin with a computerized milling machine. Some of them also manufacture their model propellers. Equipping the ship models with all drives and gauges and manufacturing equipment for non-standard model tests are the main tasks of the workshops.

Some ship model basins have further facilities, for example:

  • A maneuvering and seakeeping basin. This is a test facility that is wide enough to investigate arbitrary angles between waves and the ship model, and to perform maneuvers like turning circles, for which the towing tank is too narrow. However, some important maneuvers like the spiral test still require even more space and still have to be simulated numerically after system identification.
  • An Ice Tank: To develop ice breaking vessels, this tank fulfills similar purposes as the towing tank does for open water vessels. Resistance and required engine power as well as maneuvering behaviour are determined depending on the ice thickness. Also ice forces on offshore structures can be determined. Ice layers are frozen with a special procedure to scale down the ice crystals to model scale. Also tests in brash ice are performed.

Additionally, these companies or authorities have CFD software and experience to simulate the complicated flow around ships and their rudders and propellers numerically. Today's state of the art does not yet allow software to replace model tests in their entirety by CFD calculations. One reason, but not the only one, is that elementization is still expensive. Also the lines design of some of the ships is carried out by the specialists of the ship model basin, either from the beginning or by optimizing the initial design obtained from the shipyard. The same applies to the design of propellers.

The ship model basins worldwide are organized in the ITTC [1] (International Towing Tank Conference) to standardize their model test procedures.

Some of the most significant ship model basins are the David Taylor Model Basin and the Davidson Laboratory [2] at Stevens Institute of Technology in the United States, The High Speed Towing Tank facility at Naval Science and Technological Labs at Vizag India, The Institute for Ocean Technology [3] in St. Johns, Canada, FORCE Technology [4] in Lyngby, Denmark, SSPA, [5] in Gothenburg, Sweden, the Maritime Research Institute Netherlands (MARIN) [6] in Wageningen, the Netherlands, the INSEAN in Rome, Italy, the SVA Potsdam [7] in Potsdam, the HSVA [8] in Hamburg, Germany, the "Bassin d'essai des carènes" in Val de Reuil [9], France and CEHIPAR [10] in Madrid, Spain, CTO S.A. [11] in Gdansk, Poland

References

Ultramarine Inc. web page on vessel modeling

External Links


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • model basin — noun or model tank : a tank in which ship models are tested (as for inertia) by being towed at various speeds …   Useful english dictionary

  • David Taylor Model Basin — Taylor, David W., Model Basin U.S. National Register of Historic Places …   Wikipedia

  • Ship stability — is an area of Naval Architecture and ship design that deals with how a ship behaves at sea, both in still water and in waves. Considerations are made as to the center of gravity and center of buoyancy of vessels and how they interact. History… …   Wikipedia

  • Ship — A ship IPA|/ʃɪp/ audio|en us ship.ogg|Audio (US) is a large vessel that floats on water. Ships are generally distinguished from boats based on size. Ships may be found on lakes, seas, and rivers and they allow for a variety of activities, such as …   Wikipedia

  • Model yachting — This article is concerned with model vessels that are operated, either though programatic means or by remote control. For models intended for static display see ship model San Francisco Model Yacht Club X class (1000 square inches, few other… …   Wikipedia

  • Landing Ship, Tank — A Canadian LST off loads an M4 Sherman during the Allied invasion of Sicily in 1943. Landing Ship, Tank (LST) was the military designation for naval vessels created during World War II to support amphibious operations by carrying significant… …   Wikipedia

  • Cyclone class patrol ship — In 1990, the Navy awarded a contract to Bollinger Machine Shop and Shipyard of Lockport, LA for construction of eight Patrol Coastal (PC) ships based on the Vosper Thornycroft Patrol Craft hull design. A follow on contract for five additional… …   Wikipedia

  • Ice Tank — An Ice Tank is a ship model basin whose purpose is to provide a physical modeling environment for the interaction of ship, structures, or sea floor with both ice and water. Ice Tanks may take the form of either a Towing tank or Manovering Basin.… …   Wikipedia

  • Webb Institute — Infobox University name = Webb Institute established = 1889 type = Private endowment = US $60,000,000 president = Rear Adm. Robert C. Olsen Jr. undergrad = 91 faculty = 10 city = Glen Cove state = New York country = USA campus = Suburban, 26… …   Wikipedia

  • Cavitation — is defined as the phenomenon of formation of vapour bubbles of a flowing liquid in a region where the pressure of the liquid falls below its vapour pressure. Cavitation is usually divided into two classes of behavior: inertial (or transient)… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”