Disconnect supervision

Disconnect supervision

Disconnect supervision is a term in telephony describing signaling between the telephone exchange and a connected party used to indicate that the connected call is being disconnected.

For example the called party may indicate to the telephone exchange that the call is being disconnected by the called party by allowing loop current to flow in the line.

Contents

Overview

Disconnect Supervision Signals

The signal used for Disconnect Supervision varies depending on the type of trunk being used. These signal types include:

  1. Digital E&M - Used on T1 carriers with Channel Associated Signalling trunks
  2. Analog E&M - Used for analog E&M (earth & magneto, or ear & mouth) signalling trunks
  3. Analog Disconnect Tone - Used in many South American countries on analog loop start trunks
  4. Analog Open Switching Interval (OSI) - Used in North America on analog loop start trunks[1]
  5. Digital ISDN - Used with both PRI and BRI digital trunks

CAS E&M Signalling Basics

For Channel Associated Signalling (CAS) trunks that run (E&M) signaling, there are generally only two states in which a voice channel can be. When there is no call on a channel, the channel is in the Idle, or On-Hook state. When there is an active call on a channel, then the channel is in the Seized, or Off-Hook state. There is no separate state for Answered.

After a channel is initially seized, each device must indicate the progress of a call. The progress indicators include whether a call is answered or remains unanswered, and when a call is answered, which party disconnects first. These call progress states are important as Telephony systems need to know when the call was attempted, answered, and cleared, hence the term Answer and Disconnect Supervision.

Why Answer and Disconnect Supervision is Required

The most obvious reasons for Answer and Disconnect Supervision are for billing—the telephone exchange and the customer's need for an accurate indication of calls through a network. It is standard for telephone companies to not charge for unanswered or unsuccessful calls. All call detail records (CDRs) produced should indicate a call was unanswered or unsuccessful, and therefore, incur no charge from the billing system.

Secondly, some systems may not cut through the audio path until there is a positive indication that the called party answered the call—there may not be an audio connection until the answer signal is sent.

Lastly, the channel should become free to take new calls when the previous call clears. If there was no indication of the call's disconnect, thus no teardown or clearing then all channels in the system would eventually be blocked.

How it works

This example shows a T1 trunk using E&M wink start signaling only. Other methods can be used, although this is the most common.

Wink start is used to notify the remote side that it can send the Dialed Number Identification Service (DNIS), also referred to as the called number. Automatic Number Identification (ANI) can also be transmitted.

For an incoming call, this occurs:

  1. Calling switch goes off-hook. It sends ABCD bits = 1111.
  2. The called switch sends wink. The ABCD bits transition from 0000 to 1111 for 200 ms, then back to 0000.
  3. The calling switch sees the wink, and then proceeds to send DNIS (called number) information. This is done when in-band multifrequency/dual tone multifrequency (MF/DTMF) tones are sent.
  4. The Called Switch goes off-hook when the call is answered. It sends ABCD bits = 1111.
  5. The audio path is connected, parties can talk, and the billing system registers a call start record.

In an outgoing call the same procedure occurs, but the Calling Switch and Called Switch exchange roles.

These occur when a disconnect from the calling party happens:

  1. Calling switch goes on-hook by sending ABCD bits = 0000.
  2. The called switch sees the network go on-hook and the switch goes on-hook. ABCD bits = 0000.
  3. The audio path is disconnected, and the billing system registers a call stop record.

For a disconnect from the called party to the calling party, these steps are reversed.

Notes

As described above, when the line is in an idle condition or "on-hook" there is no presence of dial tone. If in fact a fast busy tone is heard, then there is something wrong with the line itself.

See also

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Answer supervision — is a term in telephony, describing a situation whereby the called party indicates to the central office that the call is being answered by the called party. by allowing loop current to flow in the line.OverviewCAS E M Signaling BasicsFor digital… …   Wikipedia

  • Loop start — In telecommunications, a loop start is a supervisory signal given by a telephone or PBX in response to the completion of the loop circuit, commonly referred to as off hook . When idle, or on hook , the loop is at 48V DC (provided by the CO or FXS …   Wikipedia

  • Signalling (telecommunications) — In telecommunication, signalling (UK spelling) or signaling (US spelling) has the following meanings: *The use of signals for controlling communications. *In a telecommunications network, the information exchange concerning the establishment and… …   Wikipedia

  • Signaling (telecommunications) — In telecommunication, signaling (signalling in British spelling) has the following meanings: the use of signals for controlling communications the information exchange concerning the establishment and control of a telecommunication circuit and… …   Wikipedia

  • Busy signal — For other uses, see Busy signal (disambiguation). A busy signal (or busy tone or engaged tone) in telephony is an audible or visual signal to the calling party that indicates failure to complete the requested connection of that particular… …   Wikipedia

  • OSI — is primarily used as an abbreviation and has many meanings: Contents 1 General 2 Government 3 Technology 4 Entertainment 5 …   Wikipedia

  • On-hook — In telephony, the term on hook has the following meanings: The condition that exists when a telephone or other user instrument is not in use, i.e., when idle waiting for a call. Note: on hook originally referred to the storage of an idle… …   Wikipedia

  • HDLC — High Level Data Link Control Pile de protocoles 7 • Application 6 • Présentation 5 • Session 4 • …   Wikipédia en Français

  • High-Level Data Link Control — Pile de protocoles 7.  Application 6.  Présentation 5.  Session 4.  Tr …   Wikipédia en Français

  • High-level data link control — Pile de protocoles 7 • Application 6 • Présentation 5 • Session 4 • …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”