Potential flow

Potential flow
Potential-flow streamlines around a NACA 0012 airfoil at 11° angle of attack, with upper and lower streamtubes identified.

In fluid dynamics, potential flow describes the velocity field as the gradient of a scalar function: the velocity potential. As a result, a potential flow is characterized by an irrotational velocity field, which is a valid approximation for several applications. The irrotationality of a potential flow is due to the curl of a gradient always being equal to zero.

In the case of an incompressible flow the velocity potential satisfies Laplace's equation, and potential theory is applicable. However, potential flows also have been used to describe compressible flows. The potential flow approach occurs in the modeling of both stationary as well as nonstationary flows.

Applications of potential flow are for instance: the outer flow field for aerofoils, water waves, electroosmotic flow, and groundwater flow. For flows (or parts thereof) with strong vorticity effects, the potential flow approximation is not applicable.

Contents

Characteristics and applications

A potential flow is constructed by adding simple elementary flows and observing the result.
Streamlines for the incompressible potential flow around a circular cylinder in a uniform onflow.

Description and characteristics

In fluid dynamics, a potential flow is described by means of a velocity potential φ, being a function of space and time. The flow velocity v is a vector field equal to the gradient, ∇, of the velocity potential φ:[1]

 \mathbf{v} = \nabla \varphi.

Sometimes, also the definition v = −∇φ, with a minus sign, is used. But here we will use the definition above, without the minus sign. From vector calculus it is known, that the curl of a gradient is equal to zero:[1]

\nabla \times \nabla \varphi = \mathbf{0},

and consequently the vorticity, the curl of the velocity field v, is zero:[1]

\nabla \times \mathbf{v} = \mathbf{0}.

This implies that a potential flow is an irrotational flow. This has direct consequences for the applicability of potential flow. In flow regions where vorticity is known to be important, such as wakes and boundary layers, potential flow theory is not able to provide reasonable predictions of the flow.[2] Fortunately, there are often large regions of a flow where the assumption of irrotationality is valid, which is why potential flow is used for various applications. For instance in: flow around aircraft, groundwater flow, acoustics, water waves, and electroosmotic flow.[3]

Incompressible flow

In case of an incompressible flow — for instance of a liquid, or a gas at low Mach numbers; but not for sound waves — the velocity v has zero divergence:[1]

\nabla \cdot \mathbf{v} =0,

with the dot denoting the inner product. As a result, the velocity potential φ has to satisfy Laplace's equation[1]

\nabla^2 \varphi = 0,

where \nabla^2 = \nabla \cdot \nabla is the Laplace operator (sometimes also written Δ). In this case the flow can be determined completely from its kinematics: the assumptions of irrotationality and zero divergence of the flow. Dynamics only have to be applied afterwards, if one is interested in computing pressures: for instance for flow around airfoils through the use of Bernoulli's principle.

In two dimensions, potential flow reduces to a very simple system that is analyzed using complex analysis (see below).

Compressible flow

Steady flow

Potential flow theory can also be used to model irrotational compressible flow. The full potential equation, describing a steady flow, is given by:[4]


  \begin{align}
  & 
  \left( 1 - M_x^2 \right) \frac{\partial^2 \Phi}{\partial x^2}
  + \left( 1 - M_y^2 \right) \frac{\partial^2 \Phi}{\partial y^2}
  + \left( 1 - M_z^2 \right) \frac{\partial^2 \Phi}{\partial z^2}
  \\
  & \quad
  - 2 M_x M_y \frac{\partial^2 \Phi}{\partial x\, \partial y}
  - 2 M_y M_z \frac{\partial^2 \Phi}{\partial y\, \partial z}
  - 2 M_z M_x \frac{\partial^2 \Phi}{\partial z\, \partial x} 
  = 0,
  \end{align}

with Mach number components

M_x = \frac{1}{a} \frac{\partial \Phi}{\partial x},   M_y = \frac{1}{a} \frac{\partial \Phi}{\partial y}   and   M_z = \frac{1}{a} \frac{\partial \Phi}{\partial z},  

where a is the local speed of sound. The flow velocity v is again equal to ∇Φ, with Φ the velocity potential. The full potential equation is valid for sub-, trans- and supersonic flow at arbitrary angle of attack, as long as the assumption of irrotationality is applicable.[4]

In case of either subsonic or supersonic (but not transsonic or hypersonic) flow, at small angles of attack and thin bodies, an additional assumption can be made: the velocity potential is split into an undisturbed onflow velocity V in the x-direction, and small a perturbation velocity ∇φ thereof. So:[4]

\nabla \Phi = V_\infty x + \nabla \varphi.

In that case, the linearized small-perturbation potential equation — an approximation to the full potential equation — can be used:[4]


  \left(1-M_\infty^2\right) \frac{\partial^2 \varphi}{\partial x^2} + \frac{\partial^2 \varphi}{\partial y^2} + \frac{\partial^2 \varphi}{\partial z^2} = 0,

with M = V / a the Mach number of the incoming free stream. This linear equation is much easier to solve than the full potential equation: it may be recast into Laplace's equation by a simple coordinate stretching in the x-direction.

Sound waves

Small-amplitude sound waves can be approximated with the following potential-flow model:[7]

\frac{\partial^2 \varphi}{\partial t^2} = \overline{a}^2 \Delta \varphi,

which is a linear wave equation for the velocity potential φ. Again the oscillatory part of the velocity vector v is related to the velocity potential by v = ∇φ, while as before Δ is the Laplace operator, and ā is the average speed of sound in the homogeneous medium. Note that also the oscillatory parts of the pressure p and density ρ each individually satisfy the wave equation, in this approximation.

Applicability and limitations

Potential flow does not include all the characteristics of flows that are encountered in the real world. For example, potential flow excludes turbulence, which is commonly encountered in nature. Also, potential flow theory cannot be applied for viscous internal flows.[2] Richard Feynman considered potential flow to be so unphysical that the only fluid to obey the assumptions was "dry water".[8]

Incompressible potential flow also makes a number of invalid predictions, such as d'Alembert's paradox, which states that the drag on any object moving through an infinite fluid otherwise at rest is zero.[9]

More precisely, potential flow cannot account for the behaviour of flows that include a boundary layer.[2]

Nevertheless, understanding potential flow is important in many branches of fluid mechanics. In particular, simple potential flows (called elementary flows) such as the free vortex and the point source possess ready analytical solutions. These solutions can be superposed to create more complex flows satisfying a variety of boundary conditions. These flows correspond closely to real-life flows over the whole of fluid mechanics; in addition, many valuable insights arise when considering the deviation (often slight) between an observed flow and the corresponding potential flow.

Potential flow finds many applications in fields such as aircraft design. For instance, in computational fluid dynamics, one technique is to couple a potential flow solution outside the boundary layer to a solution of the boundary layer equations inside the boundary layer.

The absence of boundary layer effects means that any streamline can be replaced by a solid boundary with no change in the flow field, a technique used in many aerodynamic design approaches. Another technique would be the use of Riabouchinsky solids.[dubious ]

Analysis for two-dimensional flow

Potential flow in two dimensions is simple to analyze using conformal mapping, by the use of transformations of the complex plane. However, use of complex numbers is not required, as for example in the classical analysis of fluid flow past a cylinder. It is not possible to solve a potential flow using complex numbers in three dimensions.[10]

The basic idea is to use a holomorphic (also called analytic) or meromorphic function f, which maps the physical domain (x,y) to the transformed domain (φ,ψ). While x, y, φ and ψ are all real valued, it is convenient to define the complex quantities

z=x+iy\,   and   w=\varphi+i\psi.\,

Now, if we write the mapping f as[10]

 f(x+iy)=\varphi+i\psi\,   or    f(z)=w.\,

Then, because f is a holomorphic or meromorphic function, it has to satisfy the Cauchy-Riemann equations[10]


\frac{\partial\varphi}{\partial x}=\frac{\partial\psi}{\partial y},
\qquad
\frac{\partial\varphi}{\partial y}=-\frac{\partial\psi}{\partial x}.

The velocity components (u,v), in the (x,y) directions respectively, can be obtained directly from f by differentiating with respect to z. That is[10]

\frac{df}{dz}=u-iv

So the velocity field v = (u,v) is specified by[10]


u=\frac{\partial\varphi}{\partial x}=\frac{\partial\psi}{\partial y},\qquad
v=\frac{\partial\varphi}{\partial y}=-\frac{\partial\psi}{\partial x}.

Both φ and ψ then satisfy Laplace's equation:[10]

\Delta\varphi = \frac{\partial^2\varphi}{\partial x^2} + \frac{\partial^2\varphi}{\partial y^2} = 0   and   \Delta\psi = \frac{\partial^2\psi}{\partial x^2} + \frac{\partial^2\psi}{\partial y^2} = 0.

So φ can be identified as the velocity potential and ψ is called the stream function.[10] Lines of constant ψ are known as streamlines and lines of constant φ are known as equipotential lines (see equipotential surface).

Streamlines and equipotential lines are orthogonal to each other, since[10]


  \nabla \phi \cdot \nabla \psi =
  \frac{\partial\phi}{\partial x}\frac{\partial\psi}{\partial x}+
  \frac{\partial\phi}{\partial y}\frac{\partial\psi}{\partial y}=
  {\partial \psi \over \partial y} {\partial \psi \over \partial x} -
  {\partial \psi \over \partial x} {\partial \psi \over \partial y} = 0.

Thus the flow occurs along the lines of constant ψ and at right angles to the lines of constant φ.[10]

It is interesting to note that Δψ = 0 is also satisfied, this relation being equivalent to ∇×v = 0. So the flow is irrotational. The automatic condition 2Ψ /( ∂x ∂y) = ∂2Ψ /( ∂y ∂x) then gives the incompressibility constraint ∇·v = 0.

Examples of two-dimensional potential flows

General considerations

Any differentiable function may be used for f. The examples that follow use a variety of elementary functions; special functions may also be used.

Note that multi-valued functions such as the natural logarithm may be used, but attention must be confined to a single Riemann surface.

Power laws

Conformal power half.svg
Conformal power two third.svg
Conformal power one.svg
Conformal power one and a half.svg
Conformal power two.svg
Conformal power three.svg
Conformal power minus one.svg
Examples of conformal maps for the power law w = A zn, for different values of the power n. Shown is the z-plane, showing lines of constant potential φ and streamfunction ψ, while w = φ + .

In case the following power-law conformal map is applied, from z = x+iy to w = φ+:[11]

w=Az^n, \,

then, writing z in polar coordinates as z = x + iy = reiθ, we have[11]

\varphi=Ar^n\cos n\theta\,   and   \psi=Ar^n\sin n\theta.\,

In the figures to the right examples are given for several values of n. The black line is the boundary of the flow, while the darker blue lines are streamlines, and the lighter blue lines are equi-potential lines. Some interesting powers n are:[11]

  • n = ½ : this corresponds with flow around a semi-infinite plate,
  • n = ⅔ : flow around a right corner,
  • n = 1 : a trivial case of uniform flow,
  • n = 2 : flow through a corner, or near a stagnation point, and
  • n = -1 : flow due to a source doublet

The constant A is a scaling parameter: its absolute value |A| determines the scale, while its argument arg{A} introduces a rotation (if non-zero).

Power laws with n = 1: uniform flow

If w = Az1, that is, a power law with n = 1, the streamlines (i.e. lines of constant ψ) are a system of straight lines parallel to the x-axis. This is easiest to see by writing in terms of real and imaginary components:


f(x+iy)=A\times(x+iy)=Ax+i\cdot Ay

thus giving φ = Ax and ψ = Ay. This flow may be interpreted as uniform flow parallel to the x-axis.

Power laws with n = 2

If n = 2, then w = Az2 and the streamline corresponding to a particular value of ψ are those points satisfying


\psi=Ar^2\sin 2\theta,\,

which is a system of rectangular hyperbolae. This may be seen by again rewriting in terms of real and imaginary components. Noting that \sin 2\theta=2\sin\theta\,\cos\theta and rewriting sin θ = y / r and cos θ = x / r it is seen (on simplifying) that the streamlines are given by


\psi=2Axy.\,

The velocity field is given by \nabla\varphi, or


\begin{pmatrix} 
  u 
  \\ 
  v 
\end{pmatrix} = 
\begin{pmatrix} 
  \displaystyle {\partial \varphi \over \partial x}
  \\[2ex]
  \displaystyle {\partial \varphi \over \partial y} 
\end{pmatrix} = 
\begin{pmatrix} 
  \displaystyle + {\partial \psi \over \partial y}
  \\[2ex]
  \displaystyle - {\partial \psi \over \partial x}
\end{pmatrix} =
\begin{pmatrix}
  +2Ax
  \\[2ex]
  -2Ay
\end{pmatrix}.

In fluid dynamics, the flowfield near the origin corresponds to a stagnation point. Note that the fluid at the origin is at rest (this follows on differentiation of f(z) = z2 at z = 0).

The ψ = 0 streamline is particularly interesting: it has two (or four) branches, following the coordinate axes, i.e. x = 0 and y = 0.

As no fluid flows across the x-axis, it (the x-axis) may be treated as a solid boundary. It is thus possible to ignore the flow in the lower half-plane where y < 0 and to focus on the flow in the upper half-plane.

With this interpretation, the flow is that of a vertically directed jet impinging on a horizontal flat plate.

The flow may also be interpreted as flow into a 90 degree corner if the regions specified by (say) x < 0 and y < 0 are ignored.

Power laws with n = 3

If n = 3, the resulting flow is a sort of hexagonal version of the n = 2 case considered above. Streamlines are given by, ψ = 3x2yy3 and the flow in this case may be interpreted as flow into a 60 degree corner.

Power laws with n = −1: doublet

If n=\,-1, the streamlines are given by


\psi=-\frac{A}{r}\sin\theta.

This is more easily interpreted in terms of real and imaginary components:

 \psi = {-A y \over r^2} = {-A y \over x^2 + y^2},
 x^2 + y^2 + {A y \over \psi} = 0,

x^2+\left(y+\frac{A}{2\psi}\right)^2=\left(\frac{A}{2\psi}\right)^2.

Thus the streamlines are circles that are tangent to the x-axis at the origin. The circles in the upper half-plane thus flow clockwise, those in the lower half-plane flow anticlockwise. Note that the velocity components are proportional to r − 2; and their values at the origin is infinite. This flow pattern is usually referred to as a doublet and can be interpreted as the combination of source-sink pair of infinite strength kept at an infinitesimally small distance apart.

The velocity field is given by


(u,v)=\left( {\partial \psi \over \partial y}, - {\partial \psi \over \partial x} \right) = 
\left(A\frac{y^2-x^2}{(x^2+y^2)^2},-A\frac{2xy}{(x^2+y^2)^2}\right).

or in polar coordinates:


(u_r, u_\theta)=\left( \frac{1}{r} {\partial \psi \over \partial \theta}, - {\partial \psi \over \partial r} \right) =  
\left(-\frac{A}{r^2}\cos\theta, -\frac{A}{r^2}\sin\theta\right).

Power laws with n = −2: quadrupole

If n=\,-2, the streamlines are given by

\psi=-\frac{A}{r^2}\sin(2 \theta).

This is the flow field associated with a quadrupole.[citation needed]

See also

Notes

  1. ^ a b c d e Batchelor (1973) pp. 99–101.
  2. ^ a b c Batchelor (1973) pp. 378–380.
  3. ^ Kirby, B.J. (2010), Micro- and Nanoscale Fluid Mechanics: Transport in Microfluidic Devices., Cambridge University Press, ISBN 978-0521119030, http://www.kirbyresearch.com/textbook 
  4. ^ a b c d Anderson, J.D. (2002), Modern compressible flow, McGraw-Hill, ISBN 0072424435 , pp. 358–359.
  5. ^ Lamb (1994) §6–§7, pp. 3–6.
  6. ^ Batchelor (1973) p. 161.
  7. ^ Lamb (1994) §287, pp. 492–495.
  8. ^ Feynman, R.P.; Leighton, R.B.; Sands, M. (1964), The Feynman Lectures on Physics, 2, Addison-Wesley , p. 40-3. Chapter 40 has the title: The flow of dry water.
  9. ^ Batchelor (1973) pp. 404–405.
  10. ^ a b c d e f g h i Batchelor (1973) pp. 106–108.
  11. ^ a b c Batchelor (1973) pp. 409–413.

References

  • Lamb, H. (1994) [1932], Hydrodynamics (6th ed.), Cambridge University Press, ISBN 9780521458689 
  • Milne-Thomson, L.M. (1996) [1968], Theoretical hydrodynamics (5th ed.), Dover, ISBN 0486689700 

Further reading

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • potential flow —    Irrotational flow occurring in a conservative force field or potential field [16] …   Lexicon of Cave and Karst Terminology

  • Aerodynamic potential flow code — Aerodynamic potential flow or panel codes are used to determine the velocity and subsequently the pressure distribution on an object. This may be a simple two dimensional object, such as a circle or wing and it may be a three dimensional vehicle …   Wikipedia

  • Potential vorticity — (PV) is a quantity which is proportional to the dot product of vorticity and stratification that, following a parcel of air or water, can only be changed by diabatic or frictional processes. It is a useful concept for understanding the generation …   Wikipedia

  • Flow measurement — is the quantification of bulk fluid movement. Flow can be measured in a variety of ways. Positive displacement flow meters acumulate a fixed volume of fluid and then count the number of times the volume is filled to measure flow. Other flow… …   Wikipedia

  • Potential temperature — The potential temperature of a parcel of fluid at pressure P is the temperature that the parcel would acquire if adiabatically brought to a standard reference pressure P {0}, usually 1000 millibars. The potential temperature is denoted heta and,… …   Wikipedia

  • Flow cytometry — Analysis of a marine sample of photosynthetic picoplankton by flow cytometry showing three different populations (Prochlorococcus, Synechococcus, and picoeukaryotes) Flow cytometry (abbreviated: FCM) is a technique for counting and examining… …   Wikipedia

  • Potential density — The potential density of a fluid parcel at pressure P is the density that the parcel would acquire if adiabatically brought to a reference pressure P {0}, often 1 bar (100 kPa). Whereas density changes with changing pressure, potential density of …   Wikipedia

  • Flow velocity — In fluid dynamics the flow velocity, or velocity field, of a fluid is a vector field which is used to mathematically describe the motion of a fluid.DefinitionThe flow velocity of a fluid is a vector field: mathbf{u}=mathbf{u}(mathbf{x},t)which… …   Wikipedia

  • Flow battery — A flow battery is a form of rechargeable battery in which electrolyte containing one or more dissolved electroactive species flows through a power cell / reactor that converts chemical energy to electricity. Additional electrolyte is stored… …   Wikipedia

  • Flow-based programming — In computer science, flow based programming (FBP) is a programming paradigm that defines applications as networks of black box processes, which exchange data across predefined connections by message passing. These black box processes can be… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”