Biasing (electronics)

Biasing (electronics)

Biasing in electronics is the method of establishing predetermined voltages and/or currents at various points of a circuit to set an appropriate "operating point".

The operating point of a device, also known as "bias point" or "quiescent point" (or simply "Q-point"), is the DC voltage and/or current which, when applied to a device, causes it to operate in a certain desired fashion. The term is normally used in connection with devices such as transistors and diodes which are used in amplification or rectification.

Importance in linear circuits

Linear circuits involving transistors typically require specific DC voltages and currents to operate correctly, which can be achieved using a biasing circuit.

As an example of the need for careful biasing, consider a transistor amplifier. In linear amplifiers, a small input signal gives larger output signal without any change in shape (low distortion): the input signal causes the output signal to vary up and down about the Q-point in a manner strictly proportional to the input. However, because a transistor is nonlinear, the transistor amplifier only approximates linear operation. For low distortion, the transistor must be biased so the output signal swing does not drive the transistor into a region of extremely nonlinear operation. For a bipolar transistor amplifier, this requirement means that the transistor must stay in the "active" mode, and avoid cut-off or saturation. The same requirement applies to a MOSFET amplifier, although the terminology differs a little: the MOSFET must stay in the "active" mode (or saturation mode), and avoid cut-off or Ohmic operation (or triode mode). More detail follows.

Bipolar junction transistors

For bipolar junction transistors the bias point is chosen to keep the transistor operating in the active mode, using a variety of circuit techniques, establishing the Q-point DC voltage and current. A small signal is then applied on top of the Q-point bias voltage, thereby either modulating or switching the current, depending on the purpose of the circuit.

The quiescent point of operation is typically near the middle of DC "load line". The process of obtaining certain DC collector current at a certain DC collector voltage by setting up operating point is called biasing.

After establishing the operating point, when input signal is applied, the output signal should not move the transistor either to saturation or to cut-off. However, this unwanted shift might occur due to various reasons outlined below:

# Parameters of transistor depend on temperature. As it increases, leakage current due to minority charge carriers (ICBO) increases. As ICBO increases, ICEO also increases, causing increase in collector current IC. This produces heat at the collector junction. This process repeat, and finally Q-point may shift into saturation region. Sometimes the excess heat produced at the junction may even burn the transistor. This is known as thermal runaway.
# When a transistor is replaced by another of the same type, the Q-point may shift, due to change in parameters of transistor such as "current gain" (eta ) which changes from unit to unit.

To avoid a shift of Q-point, bias-stabilization is necessary. Various biasing circuits can be used for this purpose.

Sources

*

*

*

See also

* Small signal model
* Bipolar Junction Transistor
* Discrete Bipolar Transistor Biasing
* MOSFET

External links

* [http://www.answers.com/topic/bias-technology?cat=technology#Sci-Tech_Encyclopedia Bias] - from Sci-Tech Encyclopedia


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Biasing (disambiguation) — Biasing may refer to:* Electronics biasing, for transistors. * Biasing of outcomes,referring to changing the probability of a particular event occurring …   Wikipedia

  • Biasing — This article is about biasing in electronics. For other uses, see Biasing (disambiguation). Biasing in electronics is the method of establishing predetermined voltages and/or currents at various points of an electronic circuit to set an… …   Wikipedia

  • Bipolar transistor biasing — Bipolar transistor amplifiers must be properly biased to operate correctly. In circuits made with individual devices (discrete circuits), biasing networks consisting of resistors are commonly employed. Much more elaborate biasing arrangements are …   Wikipedia

  • THD Electronics — Infobox Company company name=THD Electronics, Ltd. company logo= company slogan= Any Tube, Any Tone, Anytime. vector logo= company type=Private genre= foundation=1986 founder=Andrew Marshall location= Seattle, Washington, USA origins= key people …   Wikipedia

  • Education and training of electrical and electronics engineers — Both electrical and electronics engineers typically possess an academic degree with a major in electrical/ electronics engineering. The length of study for such a degree is usually three or four years and the completed degree may be designated as …   Wikipedia

  • Clipper (electronics) — Voltage clipping limits the voltage to a device without affecting the rest of the waveform In electronics, a clipper is a device designed to prevent the output of a circuit from exceeding a predetermined voltage level without distorting the… …   Wikipedia

  • Langmuir probe — A Langmuir probe is a device named after Nobel Prize winning physicist Irving Langmuir, used to determine the electron temperature, electron density, and electric potential of a plasma. It works by inserting one or more electrodes into a plasma,… …   Wikipedia

  • semiconductor device — ▪ electronics Introduction       electronic circuit component made from a material that is neither a good conductor nor a good insulator (hence semiconductor). Such devices have found wide applications because of their compactness, reliability,… …   Universalium

  • Operational amplifier — A Signetics μa741 operational amplifier, one of the most successful op amps. An operational amplifier ( op amp ) is a DC coupled high gain electronic voltage amplifier with a differential input and, usually, a single ended output.[1] An op amp… …   Wikipedia

  • Bipolar junction transistor — BJT redirects here. For the Japanese language proficiency test, see Business Japanese Proficiency Test. PNP …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”