- Bell Seagull and Seamew
The Bell Woodworking Seagull and Seamew are both small
sloop -rigged marine ply sailing boats of theTrailer yacht type designed byIan Proctor , who was also responsible for the design of many small sailing dinghies in seven different classes including the extremely popular Topper, and Wanderer.The Seagull is widely regarded in the UK sailing community as a 'plywood classic' [ [http://marinedirectory.ybw.com/reprints/results_related.jsp?tem=ybw&id=28334;| 'A few extra feet can go a long way' Practical Boat OwnerJul 2001 p58-62 ] ] , - a boat which many young families learned to build and then learned to sail in. After the Seagull and Seamew Ian Proctor later went on to design similar sized boats such as the Nimrod, Eclipse, Prelude, and the Pirate.
=Seagull=
By the mid-1950’s Ian Proctor had been responsible for the design of many small sailing dinghies, however he had yet to work on anything larger, that is, until he was approached by Bell Woodworking - who were responsible for the kit of the
GP14 sailing dinghy. The Bell Woodworking Company wanted Proctor to design a small sailing cruiser which would be suitable for both coastal and inland waters. Bell also required a design that was easy to produce in kit form and a design that the amateur builder would find easy to construct. The outcome of Proctors work was the ‘Seagull’ The Seagull sold in numbers, and although Bell did not have any exact figures for the number of both kits sold and boats built in house, the number of kits is estimated to be somewhere between 250-300. It is known that some kits were also shipped to the eastern US Seaboard. In the early days of its inception many young families bought the Seagull as a kit and built it over a year or so, for some it was their first boat and they even learned to sail in the Seagull.
right|250px|thumb|Jerry_English_and_his_Bell_Seagull_at_Milford Haven, Walespecifications Seagull
LOA Length18 ft 6 in (5.64 m) Length waterline 17ft 3in ( 5.26m) Beam Width 6 ft 9 in (2.06 m) Draft Board down 3ft 9in (keel down) ( m) Draft Board up 1ft 5in (0.43 m) Displacement 17cwt ( 762kg) Ballast 350 lb ( 158 kg) Tow Mass lb ( 762kg) Rigging Masthead sloop Mast 23ft 0in ( m) single spreader, cap shrouds and a single set of lower aft shrouds Sail sMain 100ft² ( 8.3 m²) Jib < (100%) 70ft² (6.5m²) Genoa ( %) 115ft² (10.68m²) Total sail area 215ft² ( m²) Spinnaker 150ft² (13.93m²) ailing Details
Handicaps;
PHRF = ,Portsmouth = 100, Class based Handicaps CBH = , Other = ,Sailing Characteristics;What made the Seagull stand out from the crowd however was her sailing performance. Here was a DIY sailing boat, which most people perhaps would have estimated as possessing (at best) adequate performance. However the Seagull proved she could hold her own, and during testing showed that she could still sail fully canvassed in 32kt winds. For this reason, Seagulls were often raced with many showing impressive results for such a small boat.Notable Performances;Indeed it is a testament to her seakeeping ability that she has been cruised extensively by owners and crossed the Irish Sea and the English Channel on many occasions.
Accommodation
Berths = 2, Galley =yes, Head = portable, Navigation =, Maximum headroom = 1.14 m,
The cabin, (although considered small for a boat of its size by today's standards) enjoyed 1.14m (3’9”) of headroom, two berths, room for a chemical head to port and a small galley area to starboard. The cockpit was large and could seat up to six adults, or could be used if a boom tent were employed for an additional two small berths.
pecial features
Auxiliary power was provided by an outboard motor mounted on the port quarter of the transom, a small well inboard of the transom allowed the motor to be tilted out of the water when not in use. Although some boats were fitted with a small single or twin cylinder inboard engine by retrofit.
Construction
The Seagull featured a lifting keel and ballast stub which weighed 158kg (350lb) – the use of such a retractable keel at the time was seen as unusual. The keel was raised and lowered by means of a winch mechanism, which was situated in the cockpit in early boats but moved to the cabin on later kits and builds. The hull was a four plank lapstrake hard-chine design, with each plank glued and fastened to the frames.
Country of origin,= england
Hull material, ply
Manufacturer, Bell Woodworking
Plans availability,
=Seamew=Following the success of the Seagull, Bell Woodworking commissioned Proctor to design a big sister to the Seagull. This resulted in the Seamew, the first of which was built in Jan. 1963. Again she was along similar lines as the Seagull. The Seamew was given the Portsmouth no. of 106. As with the Seagull, the Seamew sold well, - a testament to the reputation and performance of the Seagull who preceded her. Roughly 150 Seamew kits and boats were produced, with some also being shipped to the USA.
pecifications
LOA Length22 ft (6.71 m) Length waterline ft in ( m) Beam Width 7 ft 4 in (2.23 m) Draft Board down ft in ( m) Draft Board up ft in ( m) Displacement lb ( kg) Ballast 500 lb (227 kg) Tow Mass lb ( kg) Rigging Masthead sloop Mast ft in ( m) single, backswept spreader Sail sMain ft² ( m²) Jib < (100%) ft² ( m²) #1 Genoa ( %) ft² ( m²) #2 Genoa ( %) ft² ( m²) #3 Genoa ( %) ft² ( m²) Total sail area ft² ( m²) Spinnaker ft² ( m²) ailing Details
Handicaps;
PHRF = ,Portsmouth = 1060,IRC = ,Class based Handicaps CBH = , Other = ,
Sailing Characteristics;As far as performance was concerned, the Seamew was similar to the Seagull, but she was 'stiffer'- the increased ballast ratio helping to achieve this.
Notable Performances;
Accommodation
Berths = 3, Galley =yes, Head = portable, Navigation =, Maximum headroom = 4ft 0 in (1.27 m) The cabin also benefitted from an extra 3" of headroom, and there were 3 berths instead of 2.With room for a chemical head to port and a small galley area to starboard. The cockpit was large and could seat up to six adults, or could be used if a boom tent were employed for an additional two small berths.
pecial features
The same retractable bulbed keel as the Seagull but heavier albeit weighing 227kg (500lb).
Construction
The hull was a four plank lapstrake hard-chine design, with each plank glued and fastened to the frames.Also the Seamew was designed to have a small inboard engine fitted to the bilge.
Country of origin, Wales
Hull material, ply
Manufacturer, Bell Woodworking
Plans availability,
=Owners Association=
There was a very active Seagull/Seamew association up until the mid 1970's. However as plywood boats (and especially homebuilt plywood boats) became less fashionable in the late 1970s and early 1980s, - giving way to fibreglass construction methods - the owners association disappeared due to lack of interest in 1983.
There is no official association presently, however it is estimated that there are still a reasonable number of these craft both afloat and ashore. A few websites have been established (see external links). In the pages of these websites there are a number of interesting articles detailing the history along with some drawings and photographs of different owners boats. A discussion forum has also been established where owners and potential owners can discuss various aspects of these craft.
References
External links
* [http://www.seagull-seamew-yachts.org/ Seagull and Seamew Owners Website]
* [http://www.seagullmew.org/ Another Seagull and Seamew Owners Website]
Wikimedia Foundation. 2010.