Chrysler Slant-6 engine

Chrysler Slant-6 engine
Chrysler Slant Six (G, RG) Engine
Slant-6 engine in 1971 Dodge Challenger
Manufacturer Chrysler Corporation
Production 1959–2000
Predecessor Flathead 6
Successor 239/3.9 V6
Displacement 170 cu in (2.8 L)
198 cu in (3.2 L)
225 cu in (3.7 L)
Cylinder block alloy Cast iron
Aluminum
Cylinder head alloy Cast iron
Valvetrain OHV
Compression ratio 8.2:1 - 8.5:1 (nominal)
Fuel system Naturally aspirated
Fuel type Carburetor
Oil system Full pressure w/full-flow filter & gerotor oil pump
Cooling system Jacketed block, Water pump to radiator

The Slant-6, known within Chrysler as the G-engine, is one of Chrysler's better known automobile engines. The engine is an inline-6 piston engine specifically designed such that the cylinders are inclined at a 30-degree angle from vertical. The 30° inclination of the Slant-6 gave a lower height overall engine package, which enabled vehicle stylists to lower hoodlines, and also made room for the water pump to be mounted with a significant lateral offset, significantly shortening the engine's overall length. In addition, the slanted cylinder block provided ample space under the hood for intake and exhaust manifolds with runners of longer and more nearly equal length compared to the "rake" or "log" style manifolds found on other inline engines. These manifolds give a more even cylinder-to-cylinder fuel distribution and are less restrictive for better airflow through the engine.

The engine was introduced in two sizes in 1960: The 170 cubic-inch (2.8 L) "LG" (Low-G, referring to the relatively short engine block casting and crankshaft stroke) in the Valiant, and the 225 CID (3.7 L) "RG" (Raised-G, referring to the relatively tall engine block casting and crankshaft stroke) in full-size Plymouth and Dodge Dart models. In 1960, the engine was referred to by Plymouth division as the "30-D Economy Six" engine, the "30-D" referring to the 30° cylinder block angle.

The G-engine was offered in various configurations in the North American market until 1983 in cars, 1987 in trucks, and 1991 for marine, agricultural and industrial use. Replacement engines were still being built in Mexico as of 2000. In addition, the G-engine was used extensively by worldwide Chrysler divisions and subsidiaries in their locally produced vehicles. It was also widely purchased by other original equipment manufacturers for installation in commercial vehicles, agricultural and industrial equipment, and boats.

The G-engine gained an enviable reputation for reliability and nearly unstoppable durability. The basic engine design incorporates much heavy-duty engineering, in part because the engine was designed from the start to be made of either iron or aluminum: The block is of a deep-skirt design, with the crankshaft axis well above the oil pan rails for structural rigidity. Although only four main bearings are used, they are of the same dimensions as those in the Hemi. Very efficient cooling and lubrication systems, a favorable rod ratio, and an extremely strong forged steel crankshaft (on engines made through mid-1976) all contributed to the engine's apparent indestructibility. In addition, the G-engine also provided better performance than most of its competition in the 1960s and 1970s. By the 1980s, the G-engine had been effectively strangled by continual addition of increasingly restrictive exhaust emission control devices, without upgrades to the combustion chamber design, piston displacement or induction system, all of which were by that time quite antiquated. G-engine use in passenger cars was rapidly phased out in the early 1980s as Chrysler Corporation shifted to front wheel drive architecture.

Contents

Significant production changes

  • The combustion chamber shape was slightly modified for 1967 to promote more complete combustion and reduce exhaust emission toxicity.
  • All G engines used forged steel crankshafts until the middle of model year 1976, when a less costly cast iron crankshaft was introduced. The cast crankshaft uses a different block, different main and connecting rod bearings and different connecting rods.
  • The counterbore in the rear flange of the crankshaft was a 1¼-inch diameter until 1967. For 1968, it was enlarged to 1½ inches. This difference has implications when swapping engines and automatic transmissions across this date line.
  • All G-engines used solid valve lifters through the 1980 model year, with the exception of a small production test of hydraulic lifters in the 1978 model year. For model year 1981, all North American G-engines received top-fed hydraulic lifters. Retrofitment in both directions is possible.
  • Emission control devices and systems, carburetor make and specification, and engine assembly details changed over the years to comply with market requirements and preferences.
  • Electronic ignition, which had been made available on V8 engines late in 1971, was made standard equipment on all engines including the RG in 1973.
  • Induction-hardened exhaust valve seats and upgraded exhaust valves were made standard in 1973 to withstand prolonged operation on no-lead fuel.

Configuration variants

170

The 170 engine was offered in model years 1960 through 1969 in North America, and through 1971 for export markets. The first vehicle to offer the 170 slant-6 was the 1960 Valiant. The engine has a bore of 3.40 in (86.4 mm) and a stroke of 3.125 in (79.4 mm) for an actual displacement of 170.2 cu in (2.8 L). Connecting rod length is 5.669 in (144.0 mm). The "LG" low-deck block was unique to the 170 engine.

198

The 198 was introduced in the North American market for model year 1970 as a more powerful base-model engine than the previous 170 engine. The increased displacement gave improved vehicle performance and lower manufacturing cost, for it was achieved with the tall RG block also used with the 225 engine by installing a crankshaft with 3.64 in (92.5 mm) stroke and connecting rods 7.006 in (178.0 mm) long, for an actual displacement of 198.3 cu in (3.2 L). In this manner, manufacturing costs were eliminated that had been caused by previously using two different blocks for the two different available sizes of slant-6 engine. The 198 engine was available through the 1974 model year.

225

The 225 used the RG (tall) block with a 3.40 in (86.4 mm) bore, a 4.125 in (104.8 mm) stroke, and 6.699 in (170.2 mm) connecting rods, for an actual displacement of 224.7 cu in (3.7 L). This undersquare geometry was a departure from the emerging trend towards oversquare engines, and gave the 225 exceptionally strong low-RPM torque characteristics. The large amount of torque available at low engine speeds caused the 225 to find favor not only as a responsive and driveable passenger car engine, but also in pickup and commercial trucks, school buses, motorhomes, forklifts, harvesters, swathers from the likes of John Deere and Massey-Ferguson, airplane tugs, and powerboats. The 225 was originally designed and introduced in 1960 for use in full-size models, and it eventually became the best known of the Slant Six engines.

Aluminum 225

Between late model year 1961 and early model year 1963, approximately 52,000 die-cast aluminum RG blocks were produced and installed in passenger cars. These open-deck blocks used integrally cast high-nickel iron cylinder liners, and bolt-in iron upper and lower main bearing caps. Internal components (crank, rods, pistons, etc.) were the same as used in the iron engine, and an iron cylinder head was used with a special copper-asbestos gasket. The aluminum block weighs about 80 lb (36 kg) less than the iron RG block.

High performance variants

Most G-engines were equipped with small-capacity carburetors and exhaust systems adequate for standard passenger car usage at low altitudes, but which tended to hamper maximum available performance at high altitudes, in heavy or race-purpose vehicles and/or where quicker acceleration was desired. To meet the demand for improved responsiveness, modified engine configurations were made available in various markets over the years.

Hyper Pak

a reproduction Hyper-Pak intake on a slant-6 engine

The Hyper Pak was a parts package made available from 1960 through 1962 at Chrysler Corporation dealer parts counters. The parts were made available to comply with the regulations of sanctioning bodies for racing events in which Valiants had been entered by factory-backed teams: All parts used had to be "stock" parts, the definition of which meant that they were available through normal factory parts channels. The Hyper Pak consisted of a very-long-ram intake manifold meant to accept a Carter AFB 4-barrel carburetor, the AFB carburetor itself and an appropriate air cleaner, dual (front-3 and rear-3) cast iron exhaust headers, a large-diameter exhaust Y-pipe to connect to these dual cast iron headers, a larger muffler, a 276°-duration camshaft with appropriate valve springs and pushrods, a heavier-duty clutch, a manual choke control, a starter motor modification template and, in the full-race version of the package, high-compression pistons designed to increase the engine's compression ratio to 10.5 from the stock 8.5. The Hyper Pak was recommended for installation only on vehicles equipped with manual transmissions, for the camshaft was of such characteristics that a high idle speed was required to prevent engine stall-out. The Hyper Pak was primarily intended for competition driving, its road manners involving rough idling and poor cold-engine driveability, a high power band and poor fuel economy. But, in competition events, it proved unbeatable. Eight factory-backed Valiants entered the 1960 NASCAR compact car race at Daytona Beach, and humbled the competition; the Valiants came in first through eighth. After a similar performance the following year, the race was dropped. A high-fidelity reproduction of the Hyper Pak intake manifold was created by noted Slant-6 builder Doug Dutra in the late 1990s; subsequently the tooling was sold to a marketer of performance equipment for inline six-cylinder engines.

Multiple carburetors

For the 1965-1968 model years, Chrysler Argentina equipped Valiant GT models with a system of dual 1-barrel carburetors and other engine specification changes. Claimed output was 180 bhp (130 kW), compared to the single-carburetor version of the engine producing 145 bhp (108 kW)

2-barrel carburetion

Export 2-barrel setup
Air cleaner decal from Australian-market 1967-'70 2bbl Slant-6 installed on US-market 1976-'79 2bbl setup

For the 1967 model year, a 2-barrel carburetor setup was released for export production. This configuration, similar to that found on marine G-engines beginning in 1965, consisted of an iron intake manifold with open-plenum 2-barrel carburetor mounting pad, a Carter BBD carburetor, and associated air cleaner, linkage and plumbing changes. Also installed on these export 2-barrel engines was a slightly hotter camshaft (244° duration rather than 240°), and a distributor with modified advance curves. This engine, rated at 160 bhp (120 kW), was popular in Central and South America, South Africa, Australia and New Zealand. Driveability characteristics were generally superior to those of the 1-barrel engine, but to avoid cutting into sales of the more expensive V8 engine, this 2-barrel setup was not offered in the North American market. Of particular note is the automatic choke design found in this export 2-barrel setup. Most Chrysler products used remote automatic chokes, with a bimetal coil spring mounted on the exhaust manifold, exposed to exhaust heat and operating a pushrod which rotated the choke lever on the carburetor. The export 2-barrel setup used an integral heat-tube style automatic choke: Air heated by the exhaust manifold was routed to a round bakelite housing on the carburetor air horn, which contained a bimetal spring acting directly on the choke lever.

Super Six

By the mid 1970s in the North American market, emission control regulations were reducing engine performance at the same time as safety regulations were making cars heavier. An increase in performance was required for the G-engine, so a 2-barrel setup was released for the 1976 model year. This was not the same as the export 2-barrel package described above; the intake manifold used a throttle-bored plenum rather than an open one, and had provisions for an EGR valve. The carburetor, a Carter BBD similar but not identical to the one used on Chrysler's 318 V8 engine, used a standard Chrysler-style remote automatic choke. A 2¼-inch exhaust headpipe was also provided, as well as 2-barrel-specific advance curves in the ignition distributor. This package, called "Super Six" by the marketing division, added between 10 and 15% to the engine's horsepower and significantly improved throttle response and driveability while maintaining compliance with emission laws.

Aftermarket

A Slant-6 with aftermarket performance parts

Many companies have provided aftermarket performance equipment for the G-engine through the years.

A wide selection of camshafts (for torque or track racing), intake manifolds, headers, various carburetion or fuel injection setups, ignition components, internal engine parts and accessories are still available on today's market.

Applications

Passenger cars, trucks, vans

See also

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Chrysler Hemi-6 Engine — The Chrysler Hemi 6 engine is a family of inline six cylinder petrol engines produced by Chrysler Australia in three piston displacements and multiple configurations. Hemi 6 engines were installed in Australian market Chrysler Valiants from 1970… …   Wikipedia

  • Chrysler Flathead engine — Manufacturer Chrysler Corporation Also called Chrysler Sidevalve engine Production 1932–1970s …   Wikipedia

  • Chrysler Valiant — Manufacturer Chrysler Australia (1962 1980) Mitsubishi Australia (1980 1981) Also called Chrysler Charger (1975 1978) Chrysler Regal (1976 1981) Dodge Utility …   Wikipedia

  • Chrysler New Yorker — Manufacturer Chrysler Corporation Production 1939–1996 Successor Chrysler LHS …   Wikipedia

  • Chrysler Fifth Avenue — Manufacturer Chrysler Corporation Production 1983–1993 (as own model) Predecessor Chrysler LeBaron (M bo …   Wikipedia

  • Chrysler Sunbeam — For the Sunbeam Talbot or Sunbeam Talbot Darracq cars, see Sunbeam. Chrysler Sunbeam Manufacturer Chrysler Europe …   Wikipedia

  • Chrysler Cordoba — 1978 1979 Chrysler Cordoba Manufacturer Chrysler Corporation Production 1975–1983 Assembly Windso …   Wikipedia

  • Chrysler Newport — Manufacturer Chrysler Corporation Production 1940–1941 1949–1950 1961–1981 Predecessor DeSoto Adventurer …   Wikipedia

  • Chrysler PowerTech engine — Manufacturer Chrysler Group, LLC Production 1999– Predecessor Chrysler LA engine The PowerTech was a new engine family for Chrysler, and was not based on the Chrysler A engine as existing Chrysler V8s were. A 4.7 L V8 came first, fitted in… …   Wikipedia

  • Chrysler M platform — Manufacturer Chrysler Corporation Production 1977 1989 Predecessor F body R body …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”