Blowoff valve

Blowoff valve

A blowoff valve (BOV) or dump valve is a pressure release system present in most turbocharged engines.

Its purpose is to prevent compressor surge, and reduce wear on the turbocharger and engine. Blowoff valves relieve the damaging effects of compressor "surge loading" by allowing the compressed air to vent to atmosphere, making a distinct hissing sound, or recirculated into the intake upstream of the compressor inlet.

Contents

Definitions

A typical piston-type dump valve, used in auto racing. Unlike a blowoff valve, this one does not vent to the atmosphere. The small hose at the top is a feed from the intake manifold.

A compressor bypass valve (CBV), also known as a pressure relief valve or diverter valve, is a manifold vacuum-actuated valve designed to release pressure in the intake system of a turbocharged vehicle when the throttle is lifted or closed. This air pressure is re-circulated back into the non-pressurized end of the intake (before the turbo) but after the mass airflow sensor.

A blowoff valve, (sometimes "hooter valve", not to be confused with a bypass valve) performs the same task but releases the air into the atmosphere instead of recirculating it. The blowoff action produces a range of distinctive hissing sounds, depending on the exit design. Some blowoff valves are sold with a trumpet-shaped exit that intentionally amplifies the sound. Some turbocharged vehicle owners may purchase a blowoff valve solely for the auditory effect even when the function is not required by normal engine operation. Motor sports governed by the FIA have made it illegal to vent unmuffled blowoff valves to the atmosphere.[citation needed]

Blowoff valves are used to prevent compressor surge, a phenomenon that readily occurs when lifting off the throttle of an unvented, turbocharged engine. When the throttle plate on a turbocharged engine closes, the high pressure air in the intake system is trapped by the throttle and a pressure wave is forced back into the compressor. The compressor wheel slows rapidly and may even stall, and the driver will notice a fluttering air sound. The rapid slowing or stalling stresses the turbo and imparts severe turbo lag if the driver accelerates immediately after the surge event.

Disadvantages

In the case where a mass airflow sensor (MAF) is used and is located upstream from the blowoff valve, the engine control unit (ECU) will meter out excess fuel because the atmospherically vented air is not subtracted from the intake charge measurements. The engine then briefly operates with a fuel-rich mixture after each valve actuation.

The rich mixing can lead to hesitation or even stalling of the engine when the throttle is closed, a situation that worsens with higher boost pressures. Occasional events of this type may be only a nuisance, but frequent events can eventually foul the spark plugs and destroy the catalytic converter, as the inefficiently combusted fuel produces soot (excess carbon) and unburned fuel in the exhaust flow can produce soot in the converter and drive the converter beyond its normal operating temperature range.

An alternative method for utilizing both a MAF and a blowoff valve is to have the MAF located down stream between the intercooler and the throttle plate. This is known as Blow-through rather than the traditional Draw-through set up. Care must be taken as to the position of the MAF to prevent damage to the sensitive element. (I.E. on a SR20DE motor, the MAF must be at least 12" from the throttle plate, and the blowoff valve must be 6" from the MAF sensor). By using a draw-through method, the MAF won't be affected by the blowoff valve opening as the pressure is vented before the air reaches the MAF.

One approach used to mitigate the problem has been to reduce the boost pressure, which reduces the required venting volume and yields less charge over-calculation by the ECU. The air can also be recirculated back into the intake, a typical stock setup for cars with an upstream MAF sensor. The situation can also be corrected by switching the fuel metering system over to a manifold absolute pressure sensor, a conversion that usually requires a compatible aftermarket ECU or piggy-back fuel controller. The MAP sensor monitors the absolute pressure in the manifold at all times and will correctly detect the change that occurs when the valve vents, allowing the ECU to reduce fuel metering accordingly.

Operation

throttle open, blowoff valve closed
throttle closed, blowoff valve open

A blowoff valve is connected by a vacuum hose to the intake manifold after the throttle plate. When the throttle is closed, the relative manifold pressure drops to below zero bar and the resulting pressure differential operates the blowoff valve's piston. The excess pressure from the turbocharger is then vented into the atmosphere or recirculated into the intake upstream of the compressor inlet.

See also

References


  • Allard, Alan. Turbocharging and Supercharging. Cambridge, England: Patrick Stevens Limited, 1982.
  • Gorla, Rama, and Khan, Aijaz. Turbomachinery Design and Theory. New York, New York: Marcel Dekker, 2003.
  • Society of Automotive Engineers. Turbochargers and Turbocharged Engines. Warrendale, PA, 1979.
  • Watson, N, and Janota, N. Turbocharging the Internal Combustion Engine. London, England: Macmillian Press Ltd, 1982.

Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • blowoff valve — prapūtimo vožtuvas statusas T sritis automatika atitikmenys: angl. blowing valve; blowoff valve; blowout valve; blowthrough valve; purge valve vok. Abblaseventil, n; Ausblaseventil, n; Schnüffelventil, n rus. продувочный вентиль, m; продувочный… …   Automatikos terminų žodynas

  • blowoff valve — A one way valve that opens to the atmosphere above a certain set pressure to relieve excessive internal pressure buildup; often used with a turbocharger installation to limit boost pressure to the engine. Also called pressure relief valve. Also… …   Dictionary of automotive terms

  • valve — A device used to either open or close an opening to allow or prevent the flow of a liquid or gas from one place to another. There are many different types. See ABS relay valve accumultor valve air valve carburetor air control valve air gulp valve …   Dictionary of automotive terms

  • blowoff — /bloh awf , of /, n. 1. a current of escaping surplus steam, water, etc.: The safety valve released a violent blowoff from the furnace. 2. a device that permits and channels such a current. 3. Slang. a person who brags or boasts; a blow hard. 4.… …   Universalium

  • blowoff cock — prapūtimo čiaupas statusas T sritis Energetika apibrėžtis Uždaromasis prapūtimo linijos įtaisas. atitikmenys: angl. blowoff cock; purge valve vok. Durchblasehahn, m; Durchblaseventil, n rus. продувочный вентиль, m; продувочный кран, m pranc.… …   Aiškinamasis šiluminės ir branduolinės technikos terminų žodynas

  • Dump valve — Dump valves are fitted to the engines of turbo charged cars and sit between the turbo outlet and the throttle body. When transitioning from a boosted state to a closed throttle state (as in between shifts), due to inertia, the turbo continues to… …   Wikipedia

  • Relief valve — The relief valve is a type of valve used to control or limit the pressure in a system or vessel which can build up by a process upset, instrument or equipment failure, or fire. The pressure is relieved by allowing the pressurised fluid to flow… …   Wikipedia

  • blowing valve — prapūtimo vožtuvas statusas T sritis automatika atitikmenys: angl. blowing valve; blowoff valve; blowout valve; blowthrough valve; purge valve vok. Abblaseventil, n; Ausblaseventil, n; Schnüffelventil, n rus. продувочный вентиль, m; продувочный… …   Automatikos terminų žodynas

  • blowout valve — prapūtimo vožtuvas statusas T sritis automatika atitikmenys: angl. blowing valve; blowoff valve; blowout valve; blowthrough valve; purge valve vok. Abblaseventil, n; Ausblaseventil, n; Schnüffelventil, n rus. продувочный вентиль, m; продувочный… …   Automatikos terminų žodynas

  • blowthrough valve — prapūtimo vožtuvas statusas T sritis automatika atitikmenys: angl. blowing valve; blowoff valve; blowout valve; blowthrough valve; purge valve vok. Abblaseventil, n; Ausblaseventil, n; Schnüffelventil, n rus. продувочный вентиль, m; продувочный… …   Automatikos terminų žodynas

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”