- Valve RF amplifier
Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.
Valves are high voltage/low current devices in comparison with
transistors (and especially MOSFETs) and their transfer characteristics show very flat anodecurrent vs. anode voltage indicating high anode output impedances.
The high working voltage makes them well suited for
radio transmitters, for example, and valves remain in use today for very high power radio transmitters, where there is still no other technology available. However, for most applications requiring an appreciable output current, a matching transformeris required. The transformer is a critical component and heavily influences the performance (and cost) of the amplifier.
Many power valves have good open-loop linearity, but only modest
gainor transconductance. As a result, valve amplifiers usually need only modest levels of feedback. Signal amplifiers using tubes are capable of very high frequency response ranges - up to radio frequency. Indeed, many of the Directly Heated Single Ended Triode(DH-SET) audio amplifiers are in fact radio transmitting tubes designed to operate in the megahertz range. In practice, however, tube amplifier designs typically "couple" stages either capacitively, limiting bandwidth at the low end, or inductively with transformers, limiting the bandwidth at high end.
Circuit advantages of valves
*very linear (especially triodes) making it viable to use them in low distortion linear circuits with little or no negative feedbackFact|date=February 2007
*extremely high input impedance (cf bipolar transistors but a characteristic shared by FETs)
*Valves are high voltage devices and thus inherently suitable for very high voltage circuits.
*Valves can be constructed on a scale that can dissipate large amounts of heat (some extreme devices even being water cooled). For this reason valves remained the only viable technology for very high power, and especially high power/high voltage applications such as Radio & TV transmitters long into the age when transistors had displaced valves in most other applications. However today these also are increasingly obsolete
*Electrically very robust, they can tolerate overloads which would destroy
bipolar transistorsystems in milliseconds (of particular significance in military and other "strategically important" systems).
Disadvantages of valves
Heatersupplies are required for the cathodes
*Dangerously high voltages are required for the anodes
*High impedance / low current output unsuitable for direct drive of many real world loads, notably various form of electric motor
*Valves may have a shorter working life than solid state parts due to various failure mechanisms (cathode poisoning, breakages (ie open circuit) or shorts internally, notably of the heater or grid structures, or in the case of glass valves, physical breakage, although this should not be overstated : many valve types typically have operation lives of the tens of thousands of hours and an indefinite shelf life (many 60 year old tubes are still in regular use), and in worst case a failed tube can simply be unplugged and replaced by a user, cf a failed transistor which normally destroys the entire product beyond economic repair
*Compared to transistors, valves have the disadvantage of being available in a single polarity only. In most processes transistors are available in complementary polarities (e.g., NPN/PNP), making possible many circuit configurations that cannot be realized with valves.
Historic radio techniques were much simpler than those used today. Early communications equipment was optimised for maximum power output (and thus range) from the simplest possible circuitry, and Class C was often used, at the expense of generating extremely high levels of distortion and consequent sidebands, and is now historic interest only
Later development of FM for broadcast rather than communications dramatically changed the design compromise in favour of greater fidelity, accepting that wider bandwidth could be used etc. However technically it becomes more difficult to provide gain bandwidth and linearity at very high frequencies, especially at microwave and above
Today's "digital" radio that carries coded data over various phase modulations (such as GMSK, QPSK etc) and also the increasing demand for spectrum have forced a dramatic change in the way radio is used, eg the cellular radio concept. Today's cellular radio standards are extremely demanding in terms of the spectral envelope and out of band emissions that are acceptable (in the case of GSM for example, -70 dB or better just a few hundred kilohertz from center frequency).
Historic transmitters and receivers
(High voltage / High power)Valve stages were used to amplify the received radio frequency signals, the intermediate frequencies, the video signal and the audio signals at the various points in the receiver. Historically (pre WWII) "transmitting tubes" were among the most powerful tubes available, were usually direct heated by thoriated filaments that glowed light light bulbs. Some tubes were built to be very rugged, capable of being driven so so hard that the anode would itself glow cherry red, the anodes being machined from solid material (rather than fabricated from thin sheet) to be able to withstand this without distorting when heated. Notable tubes of this type are the 845 and 211. Later beam power tubes such as the 807 and (direct heated) 813 were also used in large numbers in (especially military) radio transmitters.
Modern narrow band RF / tuned amplifiers
Today, radio transmitters are overwhelmingly silicon based, even at microwave frequencies (notably consider cellular radio base stations). However, while a (n ever decreasing) minority of especially high power radio frequency amplifiers continue to have valve construction, the development of radio is inseparable from valve technology and so this field remains of great historic interest.
RF circuits are significantly different from broadband circuits.
*Historically, distortion and out of band emission was less of an issue and Class C sound be used
*Broadband circuits often go down to near DC (10 Hz or below) and up to tens or hundreds of kilohertz / low megahertz, and are required to have essentially flat frequency response over this entire range (4 or more orders of magnitude). RF circuits by contrast are typically required to operate over higher frequencies (which makes capacitive and inductive parasitic effects much more of a design challenge) but often a very narrow frequency range. For example, an RF device might be required to operate over the range 144 to 146 MHz (just 1.4% of an octave)The antenna or following circuit stage typically contains one or more adjustable capacitive or inductive component allowing the resonance of the stage to be accurately matched with carrier frequency in use, to optimize power transfer from and loading on the valve, a so called "tuned circuit"
Unlike audio amplifiers, in which the analog output signal is of the same form and frequency as the input signal, RF circuits usually modulate the signal onto a carrier (at a much higher frequency), and the circuitry comprises several distinct stages, for example a "radio transmitter" or receiver will contain
*an audio frequency (AF) stage (typically using conventional broadband small signal circuitry as described in
Valve audio amplifier,
*one or more
oscillatorstages that generate the carrier frequency
*one or more
mixerstages that (de)modulate sign signal from the carrier,
*the baseband stage itself operating at (typically) very high frequency. the
Transmitter(baseband) power amp itself is the only high power stage in a radio system, and operates at the carrier (baseband) frequency and is usually a tuned circuit.
Transmitter baseband anode circuits
The most common anode circuit is a tuned LC circuit where the anodes are connected at a
voltagenode. This circuit is often known as the anode tank circuit.
Active (or tuned grid) amplifier
An example of this used at VHF/
UHFinclude the 4CX250B, an example of a twin tetrodeis the QQV06/40A.
Neutralization is a term used in valved electronics for
negative feedbackwhich is used to make the system more stable. Negative feedback counteracts the positive feedback in valve circuits. It is possible by the correct choice of the ratio of the turns in the inductive coupling to obtain a step up in drive voltage, allowing a very high gain. However, the high gain increases possible instability and with this type of amplifier, good layout is vital.
In common with all three basic designs shown here, the anode of the valve is connected to a resonant LC circuit which has another inductive coupling which allows the RF signal to be passed to the output.
The anode current is controlled by the electrical potential (voltage) of the first grid. A DC bias is applied to the valve to ensure that the part of the transfer equation which is most suitable to the required application is used. The input signal is able to perturb (change) the potential of the grid, this in turn will change the
anodecurrent (also known as the plate current).
RFdesigns shown on this page, a tuned circuitis between the anode and the high voltage supply. This tuned circuit is brought to resonance presenting an inductive load that is well matched to the valve and thus results in an efficient power transfer.
As the current flowing through the anode connection is controlled by the grid, then the current flowing through the load is also controlled by the grid.
One of the disadvantages of a tuned grid compared to other RF designs is that neutralization is required.
Passive grid amplifier
An example of a passive grid used at VHF/
UHFfrequencies include the 4CX250B; an example of a twin tetrode would be the QQV06/40A. The tetrode has a screen grid which is between the anode and the first grid, the purpose of which is to increase the stability of the circuit by reducing the capacitance between the first grid and the anode. The combination of the effects of the screen grid and the damping resistor often allow the use of this design without neutralization.
The signals come into the circuit through a capacitor, then are applied to the valve's first grid. The value of the grid resistor determines the gain of the amplifier stage. The higher the resistor the greater the gain, the lower the damping effect and the greater the risk of instability. With this type of stage good layout is less vital.
*Stable, no neutralizing required normally
*Constant load on the exciting stage
*Low gain, more input power is required
*Less gain than tuned grid
*Less filtering than tuned grid (more broadband), hence the amplification of out of band spurious signals, such as harmonics, from an exciter is greater
Grounded grid amplifier
This design uses a triode, the grid current drawn in this system is larger than that required for the other two basic designs. Because of this, valves such as the 4CX250B are not suitable for this circuit. This circuit design has been used at 1296 MHz using disk seal
triode valvessuch as the 2C39A.
The grid is kept at ground, the drive is applied to the cathode through a capacitor. The heater supply must be isolated with great care from the cathodes as unlike the other designs the cathode is not connected to RF ground. The cathodes are also at a DC potential more negative than the grounded grid, and the DC supply for the valve is likely to be more complex than the supply required for the other two designs.
*Stable, no neutralizing required normally
*Some of the power from exciting stage appears in the output
*Very low gain, much more input power is required
*The heater must be isolated with greater care from the valve with chokes
The capacitance which exists between the anode and the first grid provides some positive feedback within the valve.For the higher gain designs the positive feedback must be counteracted.Additional screen grids in RF valves reduce the unwanted capacitance between the anode and the first grid.
Class C amplifiers
Is very efficient, and was widely used historically, however it generates considerable distortion and wide sidebands. In today's "spectrum scare" world class C is little used
Transit time effects are important at these frequencies, so feedback is not normally usable and for performance critical applications alternative linearisation techniques have to be used such as degeneration and feedforward
Tube noise and noise figure
Like any amplifying device, tubes add noise to the signal to be amplified. Even with a hypothetical perfect amplifier, however, noise is unavoidably present due to thermal fluctuations in the signal source (usually assumed to be at room temperature, "T" = 295 K). Such fluctuations cause an electrical noise power of , where "k"B is the Boltzmann constant and "B" the bandwidth. Correspondingly, the voltage noise of a resistance "R" into an open circuit is and the current noise into a short circuit is . The noise figure is defined as the ratio of the noise power at the output of the amplifier relative to the noise power that would be present at the output if the amplifier were noiseless (due to amplification of thermal noise of the signal source). An equivalent definition is: noise figure is the factor by which insertion of the amplifier degrades the signal to noise ratio. It is often expressed in decibels (dB). An amplifier with a 0 dB noise figure would be perfect.
The noise properties of tubes at audio frequencies can be modelled well by a perfect noiseless tube having a source of voltage noise in series with the grid. For the EF86 tube, for example, this voltage noise is specified (see e.g., the Valvo, Telefunken or Philips data sheets) as 2 microvolts integrated over a frequency range of approximately 25 Hz to 10 kHz. (This refers to the integrated noise, see below for the frequency dependence of the noise spectral density.) This equals the voltage noise of a 25 kΩ resistor. Thus, if the signal source has an impedance of 25 kΩ or more, the noise of the tube is actually smaller than the noise of the source. For a source of 25 kΩ, the noise generated by tube and source are the same, so the total noise power at the output of the amplifier is twice the noise power at the output of the perfect amplifier. The noise figure is then two, or 3 dB. For higher impedances, such as 250 kΩ, the EF86's voltage noise is lower than the sources's own noise. It therefore adds 1/10 of the noise power caused by the source, and the noise figure is 0.4 dB. For a low-impedance source of 250 Ω, on the other hand, the noise voltage contribution of the tube is 10 times larger than the signal source, so that the noise power is one hundred times larger than that caused by the source. The noise figure in this case is 20 dB.
To obtain low noise figure the impedance of the source can be increased by a transformer. This is eventually limited by the input capacity of the tube, which sets a limit on how high the signal impedance can be made if a certain bandwidth is desired.
The noise voltage density of a given tube is a function of frequency. At frequencies above 10 kHz or so, it is basically constant ("white noise"). White noise is often expressed by an equivalent noise resistance, which is defined as the resistance which produces the same voltage noise as present at the tube input. For triodes, it is approximately (2-4)/"g"m, where "g"m is the transconductivity. For pentodes, it is higher, about (5-7)/"g"m. Tubes with high "g"m thus tend to have lower noise at high frequencies. For example, it is 300 Ω for one half of the ECC88, 250 Ω for an E188CC (both have "g"m = 12.5 mA/V) and as low as 65 Ω for a tride-connected D3a ("g"m = 40 mA/V).
In the audio frequency range (below 1-100 kHz), "1/"f" noise becomes dominant, which rises like 1/"f". (This is the reason for the relatively high noise resistamnce of the EF86 in the above example.) Thus, tubes with low noise at high frequency do not necessarily have low noise in the audio frequency range. For special low noise audio tubes, the frequency at which 1/"f" noise takes over is reduced as far as possible, maybe to something like a kilohertz. It can be reduced by choosing very pure materials for the cathode nickel, and running the tube at an optimized (generally low) anode current.
At radio frequencies, things are more complicated: (i) The input impedance of a tube has a real component that goes down like 1/"f"² (due to cathode lead inductance and transit time effects). This means the input impedance can no longer be increased arbitrarily in order to reduce the noise figure. (ii) This input resistance has its own thermal noise, just like any resistor. (The "temperature" of this resistor for noise purposes is more close to the cathode temperature than to room temperature). Thus, the noise figure of tube amplifiers increases with frequency. At 200 MHz, a noise figure of 2.5 (or 4 dB) can be reached with the ECC2000 tube in an optimized "cascode"-circuit with an optimized source impedance. At 800 MHz, tubes like EC8010 have noise figures of about 10 dB or more. Planar triodes are better, but very early, transistors have reached noise figures substantially lower than tubes at UHF. Thus, the tuners of television sets were among the first parts of consumer electronics were transistors were used.
Semiconductor amplifiers have overwhelmingly displaced valve amplifiers for low and medium power applications at all frequencies.
Valve amplifiers remain in some high power applications such as National Terrestrial TV and (VHF) FM radio, also in existing "radar, countermeasures equipment, or communications equipment" (p. 56, Symons .. a reference now a decade old) using speciallydesigned valves, such as the
klystron, gyrotron, traveling-wave tube,and crossed-field amplifier, however new designs for such products are now invariably semiconductor based. [cite journal | author=Robert S. Symons
title=Tubes: Still vital after all these years
journal=IEEE Spectrum | year=1998 | volume=35 | issue=4 | pages= 52–63
*"Radio communication handbook" (5th Ed),
Radio Society of Great Britain, 1976, ISBN 0-900612-28-2
* [http://www.geocities.com/tpsbpl/valvereciver.htm] - AM band (medium wave, short wave) old valve type Radio
* [http://www.audiocircuit.com The Audio Circuit] - An almost complete list of manufacturers, DIY kits, materials and parts and 'how they work' sections on valve amplifiers
* [http://www.sengpielaudio.com/calculator-thd Conversion calculator] - distortion factor to distortion attenuation and THD
* [http://groups.yahoo.com/group/rfamplifiers/ Yahoo rfamplifiers group] - A gathering place for those who like to design and build valve-type RF Power Amplifiers for use in ham radio
Wikimedia Foundation. 2010.
Look at other dictionaries:
Valve audio amplifier — A valve (UK) audio amplifier or vacuum tube (US) audio amplifier is a valve amplifier used for sound recording, reinforcement, or reproduction. Until the invention of solid state devices such as the transistor, all electronic amplification was… … Wikipedia
Valve audio amplifier - technical — Circuitry and performance Characteristics of valves Valves are very high input impedance (near infinite in most circuits) and high output impedance devices. They are also high voltage / low current devices.While valves themselves are described… … Wikipedia
Valve amplifier — A valve amplifier or tube amplifier is a type of electronic amplifier that make use of vacuum tubes instead of solid state semiconductor devices (such as transistors). As any other electronic amplifier they serve to increase the power and/or… … Wikipedia
Valve transmitters — Most high power transmitter amplifiers are of valve construction because of the high power required.Anode circuitsSince valves are designed to operate with much higher resistive loads than solid state devices, the most common anode circuit is a… … Wikipedia
Amplifier — For other uses, see Amplifier (disambiguation). Generally, an amplifier or simply amp, is a device for increasing the power of a signal. In popular use, the term usually describes an electronic amplifier, in which the input signal is usually a… … Wikipedia
valve amplifier — lempinis stiprintuvas statusas T sritis fizika atitikmenys: angl. tube amplifier; vacuum tube amplifier; valve amplifier vok. Röhrenverstärker, m rus. ламповый усилитель, m pranc. amplificateur à lampes, m; amplificateur à tubes électroniques, m … Fizikos terminų žodynas
valve amplifier — lempinis stiprintuvas statusas T sritis automatika atitikmenys: angl. tube amplifier; valve amplifier vok. Röhrenverstärker, m rus. ламповый усилитель, m pranc. amplificateur à tubes, m … Automatikos terminų žodynas
amplifier tube — stiprintuvinė lempa statusas T sritis fizika atitikmenys: angl. amplifier tube; amplifying tube; amplifying valve vok. Verstärkerröhre, f rus. усилительная лампа, f pranc. lampe amplificatrice, f; tube amplificateur, m … Fizikos terminų žodynas
amplifier — /ˈæmpləfaɪə / (say ampluhfuyuh) noun 1. someone who amplifies or enlarges. 2. Electricity a device for increasing the amplitudes of electric waves or impulses by means of the control exercised by the input over the power supplied to the output… … Australian English dictionary
Electronic amplifier — A practical amplifier circuit An electronic amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. In… … Wikipedia