- Downhole safety valve
A downhole safety valve refers to a component on an oil and gas well, which acts as a failsafe to prevent the uncontrolled release of reservoir fluids in the event of a worst case scenario surface disaster. It is almost always installed as a vital component on the completion.
These valves are commonly uni-directional flapper valves which open downwards, such that the flow of wellbore fluids try to push it shut, while pressure from surface pushes it open. This means that when closed, it will isolate the reservoir fluids from surface.
Most downhole safety valves are controlled hydraulically from surface, meaning they are opened using a hydraulic connection linked directly to a well control panel. When hydraulic pressure is applied down a control line, the hydraulic pressure forces a sleeve within the valve to slide downwards. This movement compresses a large spring and pushes the flapper downwards to open the valve. When hydraulic pressure is removed, the spring pushes the sleeve back up and causes the flapper to shut. In this way, it is failsafe and will isolate the wellbore in the event of a loss of the wellhead. The full designation for a typical valve is 'tubing retrievable, surface controlled, subsurface safety valve', abbreviated to TR-SCSSV.
The location of the downhole safety valve within the completion is a precisely determined parameter intended to optimise safety. There are arguments against it either being too high or too low in the well and so the final depth is a compromise of all factors. MMS regulations state that the valve must be placed no less than 100' below the mudline.
Reasons to keep it high
The further down the well the DHSV is located, the greater the potential inventory of hydrocarbons above it when closed. This means that in the event of loss of containment at surface, there is more fluid to be spilled causing environmental damage, or in the worst case, more fuel for a fire. Therefore, placing the valve higher limits this hazard.
Another reason relates to the hydraulic control line. Hydraulic pressure is required to keep the valve open as part of the failsafe design. However, if the valve is too far down the well, then the portion of the control line below the surface is larger. If it is too large, then the weight of the hydraulic fluid alone may apply sufficient pressure to keep the valve open, even with the loss of surface pressurisation.
Reasons to keep it low
As part of the role of the DHSV to isolate the surface from wellbore fluids, it is necessary for the valve to be positioned away from the well where it could potentially come to harm. This implies that it must be placed subsurface in all circumstances, i.e. in offshore wells, not above the seabed. There is also the risk of cratering in the event of a catastrophic loss of the topside facility. The valve is specifically placed below the maximum depth where cratering is expected to be a risk.
If there is a risk of methane hydrate (clathrate) plugs forming as the pressure changes through the valve due to Joule-Thomson cooling, then this is a reason to keep it low, where the rock is warmer than 30 C.
Deploying and retrieving
Most downhole safety valves installed as part of the completion design are classed as "tubing retrievable". This means that they are installed as a component of the completion string and run in during completion. Retrieving the valve, should it malfunction, requires a workover. The full name for this most common type of downhole safety valve is a Tubing Retrievable Surface Controlled Sub-Surface Valve, shortened in completion diagrams to TRSCSSV.
If a tubing retrievable valve fails, rather than go to the expense of a workover, a "wireline retrievable" valve may be used instead. This type of valve can fit inside the production tubing and is deployed on wireline after the old valve has been straddled open.
The importance of DHSVs is undisputed. Graphic images of oil wells in Kuwait on fire after the First Gulf War after their wellheads were removed, demonstrate the perils of not using the components (at the time, they were deemed unnecessary because they were onshore wells). It is, however, not a direct legal requirement in many places. In the United Kingdom, no law mandates the use of DHSVs. However, the 1974 Health & Safety at Work Act requires that measures are taken to ensure that the uncontrolled release of wellbore fluids is prevented even in the worst case. The brilliance of the act is that it does not issue prescriptive guideline for how to achieve the goal of health and safety, but merely sets out the requirement that the goal be achieved. It is up to the oil companies to decide how to achieve it and DHSVs are an important component of that decision. As such, although not a legal requirement, it is company policy for many operators in the UKCS.
While the DHSV isolates the production tubing, a loss of integrity could allow wellbore fluid to bypass the valve and escape to surface through the annulus. For wells using gas lift, it is often a requirement to install a safety valve in the 'A' annulus of the well to ensure that the surface is protected from a loss of annulus containment. However, these valves are not as common and they are not necessarily installed at the same position in the well, meaning it is possible that fluids could snake their way around the valves to surface.
- Oil well
Wikimedia Foundation. 2010.
Look at other dictionaries:
List of oil field acronyms — Contents 1 # 2 A 3 B 4 C … Wikipedia
Completion (oil and gas wells) — This article is about the oil or gas well completion. For other uses of completion, see Completion (disambiguation) In petroleum production, completion is the process of making a well ready for production (or injection). This principally involves … Wikipedia
Christmas tree (oil well) — Oil well Christmas tree In petroleum and natural gas extraction, a Christmas tree, or tree , (not wellhead as sometimes incorrectly referred to) is an assembly of valves, spools, and fittings used for an oil well, gas well, water injection well,… … Wikipedia
Coiled tubing — In the oil and gas industries, coiled tubing refers to metal piping, normally 1 to 3.25 in diameter, used for interventions in oil and gas wells and sometimes as production tubing in depleted gas wells, which comes spooled on a large reel. Coiled … Wikipedia
Well bay — A well bay is an area of an oil platform where the Christmas trees and wellheads are located. It normally consists of two levels, a lower where the wellheads are accessed and an upper where the Xmas Trees are accessed often along with the various … Wikipedia
Well intervention — A well intervention, or well work , is any operation carried out on a oil or gas well during , or at the end of its productive life, that alters the state of the well and or well geometry, provides well diagnostics or manages the production of… … Wikipedia
Workover — The term workover is used to refer to any kind of oil well intervention involving invasive techniques, such as wireline, coiled tubing or snubbing. More specifically though, it will refer to the expensive process of pulling and replacing a… … Wikipedia
забойный управляемый отсекатель скважины — — [http://slovarionline.ru/anglo russkiy slovar neftegazovoy promyishlennosti/] Тематики нефтегазовая промышленность EN subsurface controlled downhole safety valve … Справочник технического переводчика
скважинный предохранительный клапан — — [http://slovarionline.ru/anglo russkiy slovar neftegazovoy promyishlennosti/] Тематики нефтегазовая промышленность EN downhole safety valve … Справочник технического переводчика
Drilling rig — For a detailed diagram of a Petroleum drilling rig, see List of components of oil drilling rigs. Drilling rig preparing rock blasting … Wikipedia