Steel square

Steel square

"Carpenter's square" redirects here. For the plant, see Scrophularia marilandica."

The steel square is a tool that carpenters and other tradesmen use. Today the steel square is more commonly referred to as the framing square. It consists of a large arm and a smaller one, which meet at an angle of 90 degrees (a right angle). It can also be made of metals like aluminum, which is light and resistant to rust. The wider arm, two inches wide, is called the blade; the narrower arm, one and a half inches wide, the tongue. The square has many uses, including laying out common rafters, hip rafters and stairs. It has a diagonal scale, board foot scale and an octagonal scale. On the newer framing squares there are degree conversions for different pitches and fractional equivalents.

Carpenters squares are very like steel squares.

Use in stair framing



thumb|right|250px|Theoretical rise and run of stringer, placement of square, marking of tread and rise, dropping the stringer, ABC=90°,total rise of stringer = 2R-T, total run of stringer = 2AB.
Stairs usually consist of three components. They are the stringer, the tread and the riser. The stringer is the structural member that carries the load of the staircase, the tread is the horizontal part that is stepped on, and the riser board is the vertical part which runs the width of the structure. There are many types of stairs: open, closed, fully housed, winding, and so on, to mention a few of them.

Laying out a staircase requires rudimentary math. There are numerous building codes to which staircases must conform. In an open area the designer can incorporate a more desirable staircase. In a confined area this becomes more challenging. In most staircases there is one more rise than there are treads.

# The "rise" (vertical measurement), and the "run" (horizontal measurement). Note that the stringer will rest partially on the horizontal surface.
# This is a two-by-twelve piece of lumber. A framing square is placed on the lumber so that the desired rise and tread marks meet the edge of the board. The outline of the square is traced. The square is slid up the board until the tread is placed on the mark and the process is repeated.
# The board is cut along the dotted lines, and the top plumb cut and the bottom level cut are traced by holding the square on the opposite side.
# The stringer in this example has two pieces of tread stock. This allows for a slight overhang. There is also a space in between the boards. The bottom of the stringer must be cut to the thickness of the tread. This step is called "dropping the stringer". After one stringer is cut this piece becomes the pattern that is traced onto the remaining stringers.

Use in roof framing

There is a table of numbers on the face side of the steel square; this is called the rafter table. The rafter table allows the carpenter to make quick calculations based on the Pythagorean theorem. The table is organized by columns that correspond to various slopes of the roof. Each column describes a different roof inclination (pitch) and contains the following information


#Common rafter per foot of run The common rafter connects the peak of a roof (the "ridge") to the base of a roof (the plate). This number gives the length (hypotenuse) of the common rafter per twelve units of horizontal distance ("run").
#Hip or valley rafter per foot of run The hip or valley rafter also connects the ridge to the plate, but lies at a 45-degree angle to the common rafter. This number gives the length of the hip or valley rafter per seventeen units of run.
#Difference in lengths jacks The jack rafters lie in the same plane as the common rafter but connect the top plate (the wall) or ridge board to the hip or valley rafter respectively. Since the hip or valley rafter meets the ridge board and the common rafter at angles of 45 degrees, the jack rafters will have varying lengths when they intersect the hip or valley. Depending on the spacing of the rafters, their lengths will vary by a constant factor—this number is the common difference.
#This angle can be cut on the fly by aligning this given number on the blade of the steel square and the twelve-inch mark on the tongue, and drawing a line along the tongue.
#Cutting hip and valley criple rafters are all cut in a similar way.

Use of the octagon scale

Use of the Diagonal scale

Carpenter's square

In carpentry, a square or set square is a guide for establishing right angles (ninety-degree angles), usually made of metal and in the shape of a right triangle.

ee also

*Try square
*Combination square
*Speed square
*Steel square

Bibliography

*Siegele,H.H, The Steel Square, Sterling Publishing Co., 1981, isbn= 0-8069-8854-1
*Ulrey,Harry F,Carpenters and Builders Library, No.3, Theodore Audel & Co., 1972
*Schuttner,Scott, Basic Stairbuilding,The Taunton Press, 1990, isbn= 0-942391-44-6
*Spence, William P,Constructing Staircases Balustrades & Landings, Sterling Publishing Co.,Inc., 2000
*Gochnour,Chris, Fine Woodworking, 11 Essential Measuring and Woodworking Tools, , p. 75 The Taunton Press, No. 182, February 2006
* http://en.wikipedia.org/wiki/Hip_Roof


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • steel square — noun : a carpenter s square made of steel * * * Carpentry. See framing square …   Useful english dictionary

  • steel square — Carpentry. See framing square. * * * …   Universalium

  • square — squarable, adj. squarelike, adj. squareness, n. squarer, n. /skwair/, n., v., squared, squaring, adj., squarer, squarest, adv. n. 1. a rectangle having all four sides of equal length …   Universalium

  • Steel guitar — is:* A method of playing slide guitar using a steel. Resonator guitars, including round necked varieties, are particularly suitable for this style, but other types are also used, usually with modified high actions, as well as instruments produced …   Wikipedia

  • Steel-toe boots — (also known as safety toe boots, steel capped boots or safety boots) are durable boots or shoes that have a protective reinforcement in the toe, usually combined with a sole plate, which protect the foot from falling objects and punctures from… …   Wikipedia

  • Steel frame — usually refers to a building technique with a skeleton frame of vertical steel columns and horizontal I beams, constructed in a rectangular grid to support the floors, roof and walls of a building which are all attached to the frame. The… …   Wikipedia

  • Steel Spider — The Steel Spider. Art by Mike Deodato. Publication information Publisher Marvel Comics …   Wikipedia

  • steel — steellike, adj. /steel/, n. 1. any of various modified forms of iron, artificially produced, having a carbon content less than that of pig iron and more than that of wrought iron, and having qualities of hardness, elasticity, and strength varying …   Universalium

  • Steel-toe boot — A pair of well worn steel toe shoes. A pair of ISO 20345:2 …   Wikipedia

  • Square root — Measured fall time of a small steel sphere falling from various heights. The data is in good agreement with the predicted fall time of , where h is the height and g is the acceleration of gravity. In mathematics, a square root of a number x is a… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”