Controlled Combustion Engine

Controlled Combustion Engine
REVETEC X4v2 Prototype Engine

Controlled Combustion Engine (CCE) is a term used by Revetec, an engine design company, to identify a type of experimental internal combustion engine (ICE) designed by Brad Howell-Smith. It uses two counter-rotating cams instead of a crankshaft. Pairs of cylinders oppose each other in a boxer flat engine or "X" arrangement.

Contents

History

The idea came to Howell-Smith, an automotive engineer residing in Australia, during REM sleep in 1995. He designed five different engine layouts with variations on each and established Revolution Engine Technologies Pty Ltd in 1996 with a budget of A$2000. The first working prototype was built by father-in-law Peter Koch in Howell-Smith's garage. Howell-Smith founded a company named Revetec Limited and set up a research and development site in Sydney. The prototype was displayed at the 1996 Sydney International Motor Show which brought public awareness to the design. Work began on a second prototype intended for use in generators and pumps, however interest expressed by the Middle East automotive market shifted focus towards automotive applications.

Engine description

The REVETEC Engine [1] design consists of two counter-rotating "trilobate" (three lobed) cams geared together, so both cams contribute to forward motion. Two bearings run along the profile of both cams (four bearings in all) and stay in contact with the cams at all times. The bearings are mounted on the underside of the two inter-connected pistons, which maintain the desired clearance throughout the stroke.

The two cams rotate and raise the piston with a scissor-like action to the bearings. Once at the top of the stroke the air/fuel mixture is fired. This is the power stroke during which the maximum mechanical advantage is reached after the piston has moved approximately 5% of its travel from top dead centre (approx. 10° ATDC), which makes better use of the high cylinder pressures at this point in the cycle. In comparison a conventional engine reaches its maximum mechanical advantage after the piston has moved approximately 40% of its travel from top dead centre (approx. 60° ATDC). A side effect of this is a CCE can idle at a much lower RPM.

Because the piston assembly only moves in one dimension (unlike the case in an engine with connecting rods), contact with the cylinder wall is minimised, which reduces wear and lubrication requirements. The cams create less piston shock, which allows ceramic components to be used. The engine can run in either direction if symmetrical lobes are used.

The effective cranking distance is determined by the length from the point of bearing contact to the centre of the output shaft (not the stroke).

The dual bearings contact the two cams in the opposite side which cancels the side forces out. The piston assembly does not experience any side force which will reduce wear and lubrication requirements at the cylinder contact. One module which consists of a minimum of five moving components, produces six power strokes per revolution. Increasing the number of lobes on each cam to five produces ten power strokes without increasing the number of components.

Claimed Advantages

The following advantages are claimed for the CCE engine at.[2]

  • Predicted production power to dressed weight ratio is 0.40 bhp/lb.[3] For comparison a Continental 100 hp (75 kW) engine is 0.465 hp/lb, dressed[4]
  • Efficiency - Recent tests gave good results, for a gasoline engine, when running lean.[5]
  • fewer moving and total components. As a result of fewer components, more easily manufactured than conventional engines.
  • identical cylinder head assembly (“top end") to conventional engines. Most existing head technology can be either adapted or utilised.
  • Flexible design - can be four-stroke, two-stroke, petrol, diesel or gas, natural or forced aspiration.
  • Eliminated irregularly reciprocating components such as connecting rods. No second order balancing required.
  • Output shaft can be run in either direction if multilobed cams with symmetrical lobes are employed.[citation needed]
  • The CCE can be designed to operate at greatly reduced operating speeds while delivering high torque output.[6]
  • Substantial reduction in stroke reduces heat loss through cylinder wall.
  • Extended piston dwell is possible because engine design allows a lower than normal compression ratio to be used reducing power loss from compression cycle[citation needed].
  • Able to fire on a leaner mixture than conventional engines.[citation needed]
  • Maximum mechanical advantage can be applied to output shaft at only 20 degrees ATDC utilising high cylinder pressure early in the stroke, compared to around 60 degrees ATDC for conventional engines.
  • Lower emissions can be achieved due to increased control over combustion.
  • Low idle speed due to increase in mechanical efficiency at the top of the stroke.[citation needed]
  • Little or no bore contact/piston side thrust, which reduces wear on cylinder bore.
  • Can have different port timing on compression stroke than power stroke allowing better control.
  • Lower centre of gravity on the boxer design.[citation needed]
  • Due to controlled piston acceleration rates the CCE reduces engine vibration.[citation needed]
  • A hollow output shaft can be utilised for specialty applications, such as peristaltic pumps.

Disadvantages

The following have yet to be verified independently.

  • Vibration
  • Reliability, especially when running lean as is required for good economy.
  • Emissions[citation needed]

Patents

U.S. Patent 5,992,356 "Opposed piston combustion engine "; November 30, 1999; Howell-Smith; Bradely David (Worongary, AU).

Revetec has a PCT patent application pending for the "X" design lodged late 2006.

Performance

A dyno graph of the Revetec 1.38litr engine is shown on their development page, shows a flat torque curve.[1]

Test results (11 November 2007) on the X4v2 engine showing torque and power curves and the fuel injection map.[7]

In April 2008, Revetec completed their first Independently Certified Test Report carried out by Orbital Australia, achieving a repeatable BSFC figure of 212g/kW-h (38.6% efficiency) with a best tested figure of 207g/kW-h (39.5% efficiency).[5]

References

External links



Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • controlled combustion system — [1] (CCS) A system of reducing unburned hydrocarbon emission from the engine exhaust. [2] An emission control term used by General Motors to include the following: modified combustion chamber design high temperature coolant systems… …   Dictionary of automotive terms

  • Oil pump (internal combustion engine) — This article is about a part in an internal combustion engine. For other uses, see Oil pump. Oil circulation system …   Wikipedia

  • Engine balance — is the design, construction and tuning of an engine to run smoothly. Engine balance reduces vibration and other stresses, and may improve the performance, efficiency, cost of ownership and reliability of the engine, as well as reducing the stress …   Wikipedia

  • Engine control unit — An engine control unit (ECU) is an electronic control unit which controls various aspects of an internal combustion engine s operation. The simplest ECUs control only the quantity of fuel injected into each cylinder each engine cycle. More… …   Wikipedia

  • Engine — This article is about a machine to convert energy into useful mechanical motion. For other uses of engine, see Engine (disambiguation). For other uses of motor, see Motor (disambiguation). A V6 internal combustion engine from a Mercedes car An… …   Wikipedia

  • Engine knocking — Pinging redirects here. For other uses, see Ping (disambiguation). Knocking (also called knock, detonation, spark knock, pinging or pinking) in spark ignition internal combustion engines occurs when combustion of the air/fuel mixture in the… …   Wikipedia

  • Combustion — This article is about the process of burning. For combustion without external ignition, see spontaneous combustion. For the engine used in mobile propulsion, see internal combustion engine. For the visible part of a fire, see flame. Burning… …   Wikipedia

  • Engine room — In a ship, an engine room is where the main engine(s), generators, compressors, pumps, fuel/lubrication oil purifiers and other major machinery are located. It is sometimes referred to as the machinery space . Engine Rooms are typically towards… …   Wikipedia

  • combustion — The intense burning of the fuel air mixture in the combustion chamber. Some used to think that the fuel air mixture exploded; but further investigation has shown that it rapidly burns. Also see combustion chamber volume combustion chamber… …   Dictionary of automotive terms

  • Flat engine — A flat engine is an internal combustion engine with pistons that are all relatively horizontal. A straight engine canted 90 degrees from straight up is a flat engine, as is one in which the cylinders are arranged in two banks on either side of a… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”