Mohr's circle

Mohr's circle
Mohr's circles for a three-dimensional state of stress

Mohr's circle, named after Christian Otto Mohr, is a two-dimensional graphical representation of the state of stress at a point. The abscissa, \sigma_\mathrm{n}\,\!, and ordinate, \tau_\mathrm{n}\,\!, of each point on the circle are the normal stress and shear stress components, respectively, acting on a particular cut plane with a unit vector \mathbf n\,\! with components \left(n_1, n_2, n_3 \right)\,\!. In other words, the circumference of the circle is the locus of points that represent the state of stress on individual planes at all their orientations.

Karl Culmann was the first to conceive a graphical representation for stresses while considering longitudinal and vertical stresses in horizontal beams during bending. Mohr's contribution extended the use of this representation for both two- and three-dimensional stresses and developed a failure criterion based on the stress circle.[1]

Other graphical methods for the representation of the stress state at a point include the Lame's stress ellipsoid and Cauchy's stress quadric.

Contents

Mohr's circle for two-dimensional stress states

A two-dimensional Mohr's circle can be constructed if we know the normal stresses σx, σy, and the shear stress τxy. The following sign conventions are usually used:

  1. Tensile stresses (positive) are to the right.
  2. Compressive stresses (negative) are to the left.
  3. Clockwise shear stresses are plotted upward.
  4. Counterclockwise shear stresses are plotted downward.

The reason for the above sign convention is that, in engineering mechanics[2], the normal stresses are positive if they are outward to the plane of action (tension), and shear stresses are positive if they rotate clockwise about the point in consideration. In geomechanics, i.e. soil mechanics and rock mechanics, however, normal stresses are considered positive when they are inward to the plane of action (compression), and shear stresses are positive if they rotate counterclockwise about the point in consideration.[1][3][4][5]

To construct the Mohr circle of stress for a state of plane stress, or plane strain, first we plot two points in the \sigma_\mathrm{n}:\tau_\mathrm{n}\,\! space corresponding to the known stress components on both perpendicular planes, i.e. A(\sigma_y, \tau_{xy})\,\! and B(\sigma_x, -\tau_{xy})\,\! (Figure 1 and 2). We then connect points A\,\! and B\,\! by a straight line and find the midpoint O\,\! which corresponds to the intersection of this line with the \sigma_\mathrm{n}\,\! axis. Finally, we draw a circle with diameter \overline{AB}\,\! and centre at O\,\!.

The radius R\,\! of the circle is R = \sqrt{\left[\tfrac{1}{2}(\sigma_x - \sigma_y)\right]^2 + \tau_{xy}^2}\,\!, and the coordinates of its centre are \left[\tfrac{1}{2}(\sigma_x + \sigma_y), 0\right]\,\!.

The principal stresses are then the abscissa of the points of intersection of the circle with the \sigma_\mathrm{n}\,\! axis (note that the shear stresses are zero for the principal stresses).

Drawing a Mohr's circle

Figure 1. Mohr's circle for plane stress and plane strain conditions (double angle approach).

The following procedure is used to draw a Mohr's circle and to find the magnitude and direction of maximum stresses from it.

  • First, the x- and y-axes of a Cartesian coordinate system are identified as the σn-axis and τn-axis, respectively.
  • Next, two points of the Mohr's circle are plotted. These are the points B (σx, − τxy) and A (σy, τxy). The line connecting these two points is a diameter of the Mohr's circle.
  • The center of the Mohr's circle, O, is located where the diameter, AB, intersects the σ-axis. This point gives the average normal stress (σavg). The average normal stress can be read directly from a plot of the Mohr's circle. Alternatively, it can be calculated using
\sigma_\text{avg}=\tfrac{1}{2}(\sigma_x+ \sigma_y).
  • The Mohr's circle intersects the σn axis at two points, C and E. The stresses at these two end points of the horizontal diameter are σ1 and σ2, the principal stresses. The point σ1 represents the maximum normal stress (σmax) and the point σ2 is the minimum normal stress (σmin). The equations for finding these values are

\sigma_1 = \sigma_\max = \tfrac{1}{2}(\sigma_x + \sigma_y) + \sqrt{\left[\tfrac{1}{2}(\sigma_x- \sigma_y)\right]^2+ \tau_{xy}^2}

\sigma_2 = \sigma_\min = \tfrac{1}{2}(\sigma_x + \sigma_y) - \sqrt{\left[\tfrac{1}{2}(\sigma_x- \sigma_y)\right]^2+ \tau_{xy}^2}
  • Next we examine the points where the circle intersects the line parallel to τn-axis passing through the center of the circle, O. The vertical diameter of the circle passes through O (σavg) and goes up to positive τmax  and down to negative τmin . The magnitudes of extreme values are equal to the radius of the Mohr's circle, but with different signs. The equation to find these extreme values of the shear stress is[6]

\tau_{\max,\min}= \pm \sqrt{\left[\tfrac{1}{2}(\sigma_x- \sigma_y)\right]^2+ {\tau_{xy}}^2}
.
  • The next value to determine is the angle that the plane of maximum normal stress makes with the x-axis. Let us create a new X-axis by drawing a line from the center of the Mohr circle, O, through point A. Let the angle between the X-axis and the σ-axis be ϕ. If θ is the angle between the maximum normal stress and the x-axis, then it can be shown that ϕ = 2θp1. The angle ϕ is found by:
\phi = 2\theta_{p1} = \arctan\left[2\tau_{xy}/(\sigma_x- \sigma_y)\right].
  • To find the angle that the direction that the plane of maximum shear stress makes with the x-axis, we use the relation
2\theta_s =  \arctan\left[(\sigma_x - \sigma_y)/(2\tau_{xy})\right]. It is important to pay attention to the use of these two equations as they look similar.
  • Often, the final step of the process is to also draw a square stress element indicating the orientations of the maximum normal and shear stresses; the normal stress element at an angle θ and the maximum shear stress element at an angle of θs.

The previous discussion assumes, implicitly, that there are two orthogonal directions x and y that define a plane in which the stress components \sigma_x\,\!. \sigma_y\,\!, and \tau_{xy}\,\! are known. It is also implicit that these stresses are known at a point P\,\! in a continuum body under plane stress or plane strain. The Mohr circle, once drawn, can be used to find the components of the stress tensor for any other choice of orthogonal directions in the plane.

Stress components on an arbitrary plane

Figure 2. Mohr's circle for plane stress and plane strain conditions (Pole approach). Any straight line drawn from the pole will intersect the Mohr circle at a point that represents the state of stress on a plane inclined at the same orientation (parallel) in space as that line.

Using the Mohr circle one can find the stress components (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! on any other plane with a different orientation \theta\,\! that passes through point P\,\!. For this, two approaches can be used:

  • The first approach relies on the fact that the angle \theta\,\! between two planes passing through P\,\! is half the angle between the lines joining their corresponding stress points (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! on the Mohr circle and the centre of the circle (Figure 1). In other words, the stresses (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! acting on a plane at an angle \theta\,\! counterclockwise to the plane on which \sigma_x\,\! acts is determined by traveling counterclockwise around the circle from the known stress point (\sigma_x, \tau_{xy})\,\! a distance subtending an angle 2\theta\,\! at the centre of the circle (Figure 1).
  • The second approach involves the determination of a point on the Mohr circle called the pole or the origin of planes. Any straight line drawn from the pole will intersect the Mohr circle at a point that represents the state of stress on a plane inclined at the same orientation (parallel) in space as that line. Therefore, knowing the stress components \sigma\,\! and \tau\,\! on any particular plane, one can draw a line parallel to that plane through the particular coordinates \sigma_\mathrm{n}\,\! and \tau_\mathrm{n}\,\! on the Mohr circle and find the pole as the intersection of such line with the Mohr circle. As an example, let's assume we have a state of stress with stress components \sigma_x,\!, \sigma_y,\!, and \tau_{xy},\!, as shown on Figure 2. First, we can draw a line from point B\,\! parallel to the plane of action of \sigma_x\,\!, or, if we choose otherwise, a line from point A\,\! parallel to the plane of action of \sigma_y\,\!. The intersection of any of these two lines with the Mohr circle is the pole. Once the pole has been determined, to find the state of stress on a plane making an angle  \theta\,\! with the vertical, or in other words a plane having its normal vector forming an angle \theta\,\! with the horizontal plane, then we can draw a line from the pole parallel to that plane (See Figure 2). The normal and shear stresses on that plane are then the coordinates of the point of intersection between the line and the Mohr circle.

Mohr's circle for a general three-dimensional state of stresses

Figure 3. Mohr's circle for a three-dimensional state of stress

To construct the Mohr's circle for a general three-dimensional case of stresses at a point, the values of the principal stresses \left(\sigma_1, \sigma_2, \sigma_3 \right)\,\! and their principal directions \left(n_1, n_2, n_3 \right)\,\! must be first evaluated.

Considering the principal axes as the coordinate system, instead of the general x_1\,\!, x_2\,\!, x_3\,\! coordinate system, and assuming that \sigma_1 > \sigma_2 > \sigma_3\,\!, then the normal and shear components of the stress vector \mathbf T^{(\mathbf n)}\,\!, for a given plane with unit vector \mathbf n\,\!, satisfy the following equations

\begin{align}
\left( T^{(n)} \right)^2 &= \sigma_{ij}\sigma_{ik}n_jn_k \\
\sigma_\mathrm{n}^2 + \tau_\mathrm{n}^2 &= \sigma_1^2 n_1^2 + \sigma_2^2 n_2^2 + \sigma_3^2 n_3^2 \end{align}\,\!
\sigma_\mathrm{n} = \sigma_1 n_1^2 + \sigma_2 n_2^2 + \sigma_3 n_3^2\,\!

Knowing that n_i n_i = n_1^2+n_2^2+n_3^2 = 1\,\!, we can solve for n_1^2\,\!, n_2^2\,\!, n_3^2\,\!, using the Gauss elimination method which yields

\begin{align}
n_1^2 &= \frac{\tau_\mathrm{n}^2+(\sigma_\mathrm{n} - \sigma_2)(\sigma_\mathrm{n} - \sigma_3)}{(\sigma_1 - \sigma_2)(\sigma_1 - \sigma_3)} \ge 0\\
n_2^2 &= \frac{\tau_\mathrm{n}^2+(\sigma_\mathrm{n} - \sigma_3)(\sigma_\mathrm{n} - \sigma_1)}{(\sigma_2 - \sigma_3)(\sigma_2 - \sigma_1)} \ge 0\\
n_3^2 &= \frac{\tau_\mathrm{n}^2+(\sigma_\mathrm{n} - \sigma_1)(\sigma_\mathrm{n} - \sigma_2)}{(\sigma_3 - \sigma_1)(\sigma_3 - \sigma_2)} \ge 0
\end{align}\,\!

Since \sigma_1 > \sigma_2 > \sigma_3\,\!, and (n_i)^2\,\! is non-negative, the numerators from the these equations satisfy

\tau_\mathrm{n}^2+(\sigma_\mathrm{n} - \sigma_2)(\sigma_\mathrm{n} - \sigma_3) \ge 0\,\! as the denominator \sigma_1 - \sigma_2 > 0\,\! and \sigma_1 - \sigma_3 > 0\,\!
\tau_\mathrm{n}^2+(\sigma_\mathrm{n} - \sigma_3)(\sigma_\mathrm{n} - \sigma_1) \le 0\,\! as the denominator \sigma_2 - \sigma_3 > 0\,\! and \sigma_2 - \sigma_1 < 0\,\!
\tau_\mathrm{n}^2+(\sigma_\mathrm{n} - \sigma_1)(\sigma_\mathrm{n} - \sigma_2) \ge 0\,\! as the denominator \sigma_3 - \sigma_1 < 0\,\! and \sigma_3 - \sigma_2 < 0\,\!

These expressions can be rewritten as

\begin{align}
\tau_\mathrm{n}^2 + \left[ \sigma_\mathrm{n}- \tfrac{1}{2} (\sigma_2 + \sigma_3) \right]^2 \ge \left( \tfrac{1}{2}(\sigma_2 - \sigma_3) \right)^2 \\
\tau_\mathrm{n}^2 + \left[ \sigma_\mathrm{n}- \tfrac{1}{2} (\sigma_1 + \sigma_3) \right]^2 \le \left( \tfrac{1}{2}(\sigma_1 - \sigma_3) \right)^2 \\
\tau_\mathrm{n}^2 + \left[ \sigma_\mathrm{n}- \tfrac{1}{2} (\sigma_1 + \sigma_2) \right]^2 \ge \left( \tfrac{1}{2}(\sigma_1 - \sigma_2) \right)^2 \\
\end{align}\,\!

which are the equations of the three Mohr's circles for stress C_1\,\!, C_2\,\! , and C_3\,\!, with radii R_1=\tfrac{1}{2}(\sigma_2 - \sigma_3)\,\!, R_2=\tfrac{1}{2}(\sigma_1 - \sigma_3)\,\! , and R_3=\tfrac{1}{2}(\sigma_1 - \sigma_2)\,\!, and their centres with coordinates \left[\tfrac{1}{2}(\sigma_2 + \sigma_3), 0\right]\,\!, \left[\tfrac{1}{2}(\sigma_1 + \sigma_3), 0\right]\,\!, \left[\tfrac{1}{2}(\sigma_1 + \sigma_2), 0\right]\,\!, respectively.

These equations for the Mohr's circles show that all admissible stress points (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! lie on these circles or within the shaded area enclosed by them (see Figure 3). Stress points (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! satisfying the equation for circle C_1\,\! lie on, or outside circle C_1\,\!. Stress points (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! satisfying the equation for circle C_2\,\! lie on, or inside circle C_2\,\!. And finally, stress points (\sigma_\mathrm{n}, \tau_\mathrm{n})\,\! satisfying the equation for circle C_3\,\! lie on, or outside circle C_3\,\!.

References

  1. ^ a b Parry
  2. ^ The sign convention differ in disciplines such as mechanical engineering, structural engineering, and geomechanics. The engineering mechanics sign convention is used in this article.
  3. ^ Jumikis
  4. ^ Holtz
  5. ^ Brady
  6. ^ Megson, T.H.G., Aircraft Structures for Engineering Students, Fourth Edition, 2007, section 1.8

Bibliography

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Mohr-Coulomb theory — is a mathematical model (see yield surface) describing the response of a material such as rubble piles or concrete to shear stress as well as normal stress. Most of the classical engineering materials somehow follow this rule in at least a… …   Wikipedia

  • Mohr (surname) — Mohr is a German language surname and may refer to: Alexander Mohr (1892–1974), a German Expressionist artist Bill Mohr (1909–1971), an Australian rules footballer Charles Mohr (1824–1901), a German American pharmacist and botanist Christopher… …   Wikipedia

  • Mohr–Coulomb theory — Continuum mechanics …   Wikipedia

  • Circle (Big Head Todd and the Monsters song) — Circle Single by Big Head Todd and the Monsters from the album Sister Sweetly Released 1993 Format CD, compact cassette …   Wikipedia

  • Christian Otto Mohr — (October 8, 1835 – October 2, 1918) was a German civil engineer. Biography He was born on October 8, 1835 to a landowning family in Wesselburen in the Holstein region. At the age of 16 attended the Polytechnic School in Hanover. Starting in 1855 …   Wikipedia

  • List of circle topics — This list of circle topics includes things related to the geometric shape, either abstractly, as in idealizations studied by geometers, or concretely in physical space. It does not include metaphors like inner circle or circular reasoning in… …   Wikipedia

  • Círculo de Mohr — La Circunferencia de Mohr (Incorrectamente llamado Círculo de Mohr, ya que no se trabaja con un área sino con el perímetro) es una técnica usada en ingeniería y geofísica para representar gráficamente un tensor simétrico (de 2x2 o de 3x3) y… …   Wikipedia Español

  • Georg Mohr — Jørgen Mohr (Latinised Georg(ius) Mohr) (April 1, 1640 – January 26, 1697) was a Danish mathematician. He travelled in the Netherlands, France, and England.Mohr was born in Copenhagen. His only original contribution to geometry was the proof that …   Wikipedia

  • Stress (physics) — Stress is a measure of the average amount of force exerted per unit area. It is a measure of the intensity of the total internal forces acting within a body across imaginary internal surfaces, as a reaction to external applied forces and body… …   Wikipedia

  • Scientific phenomena named after people — This is a list of scientific phenomena and concepts named after people (eponymous phenomena). For other lists of eponyms, see eponym. NOTOC A* Abderhalden ninhydrin reaction Emil Abderhalden * Abney effect, Abney s law of additivity William de… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”