Dip soldering

Dip soldering
Dip soldering apparatus.

Dip soldering is a small-scale soldering process by which electronic components are soldered to a printed circuit board (PCB) to form an electronic assembly. The solder wets to the exposed metallic areas of the board (those not protected with solder mask), creating a reliable mechanical and electrical connection.

Dip soldering is used for both through-hole printed circuit assemblies, and surface mount. It is one of the cheapest methods to solder and is extensively used in the small scale industries of developing countries .

Dip soldering is the manual equivalent of automated wave soldering. The apparatus required is just a small tank containing molten solder. PCB with mounted components is dipped manually into the tank when the molten solder sticks to the exposed metallic areas of the board.

Contents

Dip solder process

Dip soldering is accomplished by submerging parts to be joined into a molten solder bath. Thus, all components surfaces are coated with filler metal. Solders have low surface tension and high wetting capability. There are many types of solders, each used for different applications. Such as Lead-Silver for strength at higher than room temperature. Tin-Lead is used for General Purpose; Tin-Zinc is used for Aluminum; Cadmium-Silver is used for strength at high temperatures; Zinc-Aluminum is used for Aluminum and corrosion resistance; Tin-Silver and Tin-Bismuth is used for Electronics. Because of the toxicity of lead, lead-free solders are being developed and more widely used. The molten bath can be any suitable filler metal, but the selection is usually confined to the lower melting point elements. The most common dip soldering operations use zinc-aluminum and tin-lead solders.

Process Schematic

The workpieces to be joined are treated with cleaning flux. Then the workpiece is mounted in the workholding device and immersed in the molten solder for 2 to 12 seconds. The workpiece is often agitated to aid the flow of the solder. The workpiece holder must allow an inclination of 3 to 5 deg. so that the solder may run off to insure a smooth finish.

Workpiece Geometry

This process is generally limited to all metal work pieces, although other materials, such as circuit boards can also tolerate momentary contact with the hot molten solder without damage.

Setup and Equipment

There is not much equipment or setup for this process, all that is needed is the solder pot with its temperature control panel, the bath of molten solder, and the work holding device. Usually the work holding device is custom made for each respective workpiece for either manual or automated dipping.[1]

Solderability

Some materials are easier to solder than others. Copper, silver, and gold are easy to solder. Iron and Nickel are a little more difficult. Titanium, magnesium, cast irons, steels, ceramics, and graphites are hard to solder. However, if they are first plated they are more easily soldered. An example of this is tin-plating, in which a steel is sheet coated with tin so that it can be soldered more easily.

Applications

Dip Soldering is used extensively in the electronics industry. However, they have a limited service use at elevated temperatures because of the low melting point of the filler metals. Soldered materials do not have much strength and are therefore not used for load-bearing. [2]

References

  1. ^ Robert H. Todd and Dell K. Allen and Leo Alting, Manufacturing Processes Reference Guide
  2. ^ Soldering of Non-Ferrous Alloys

Further reading

  • Kalpakjian, Serope, and Steven R. Schmid. Manufacturing Engineering and Technology: Fifth Edition. Upper Saddle River, NJ: Pearson Education, 2006

Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • dip soldering — merkiamasis litavimas statusas T sritis radioelektronika atitikmenys: angl. dip soldering vok. Tauchlötung, f rus. пайка погружением, f pranc. soudage par immersion, m …   Radioelektronikos terminų žodynas

  • selective dip soldering — atrankusis merkiamasis litavimas statusas T sritis radioelektronika atitikmenys: angl. selective dip soldering vok. selektive Tauchlötung, f rus. избирательная пайка погружением, f pranc. soudage sélectif par immersion, m …   Radioelektronikos terminų žodynas

  • Soldering — For the song, see Soldering (song). For the product, see Solder. Desoldering a contact from a wire. Soldering is a process in which two or more metal items are joined together by melting and flowing a filler metal (solder) into the joint, the… …   Wikipedia

  • soldering — Process that uses metal alloys with low melting points to join metallic surfaces without melting them. Tin lead solders, once widely used in the electrical and plumbing industries, are now replaced by lead free alloys. Such alloys are also used… …   Universalium

  • Selective soldering — is the process of selectively soldering components to printed circuit boards, molded modules, etc. that could be damaged by the heat of a reflow oven in a traditional SMT assembly process. Consequently this process usually follows an SMT oven… …   Wikipedia

  • Taxonomy of manufacturing processes — This tree lists various manufacturing processes arranged by similarity of function.#Casting ##Sand casting ##Plastic mold ##Shell mold ##Investment casting (lost wax, precision) ##Permanent mold ##Centrifugal casting ##Die casting ##Slush or… …   Wikipedia

  • пайка погружением — — [Я.Н.Лугинский, М.С.Фези Жилинская, Ю.С.Кабиров. Англо русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.] Тематики электротехника, основные понятия EN dip brazingdip soldering …   Справочник технического переводчика

  • Tauchlötung — merkiamasis litavimas statusas T sritis radioelektronika atitikmenys: angl. dip soldering vok. Tauchlötung, f rus. пайка погружением, f pranc. soudage par immersion, m …   Radioelektronikos terminų žodynas

  • merkiamasis litavimas — statusas T sritis radioelektronika atitikmenys: angl. dip soldering vok. Tauchlötung, f rus. пайка погружением, f pranc. soudage par immersion, m …   Radioelektronikos terminų žodynas

  • soudage par immersion — merkiamasis litavimas statusas T sritis radioelektronika atitikmenys: angl. dip soldering vok. Tauchlötung, f rus. пайка погружением, f pranc. soudage par immersion, m …   Radioelektronikos terminų žodynas

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”