ISO 25178

ISO 25178

ISO 25178 means a collection of international standards relating to the analysis of 3D areal surface texture.

This standard was prepared by work group WG16 of the ISO (International Organisation for Standardisation) technical committee TC213.

It is the first international standard taking into account the specification and measurement of 3D surface texture. In particular, the standard defines 3D surface texture parameters and the associated specification operators. It also describes the applicable measurement technologies, calibration methods, together with the physical calibration standards and calibration software that are required.

A major new feature incorporated into the standard is coverage of non-contact measurement methods, already commonly used by industry, but up until now lacking a standard to support quality audits within the framework of ISO 9000. For the first time, the standard brings 3D surface metrology methods into the official domain, following 2D profilometric methods that have been subject to standards for over 30 years. The same thing applies to measurement technologies that are not restricted to contact measurement (with a diamond point stylus), but can also be optical, such as chromatic confocal gauges and interferometric microscopes.

Structure of the standard

"'General title :

ISO 25178 : Geometric Product Specifications (GPS) – Surface texture : areal

"'Documents constituting the standard :

* Part 1: surface texture indications
* Part 2: terms, definitions and surface texture parameters
* Part 3: specification operators
* Part 6: classification of methods for measuring surface texture
* Part 601: nominal characteristics of contact (stylus) instruments
* Part 602: nominal characteristics of non-contact (confocal chromatic probe) instruments
* Part 603: nominal characteristics of non-contact (wavefront interferometric microscope) instruments
* Part 701: calibration and measurement standards for contact (stylus) instruments

Other documents are in draft or being drafted and will been published in the next few years. A number of documents that are in draft concern, in particular, other optical measurement technologies (3D confocal microscope, white light interferometric microscope, digital holographic microscope).

New definitions

The ISO 25178 standard is considered by TC213 as first and foremost providing a redefinition of the foundations of surface texture, based upon the principle that nature is intrinsically 3D. It is anticipated that future work will extend these new concepts into the domain of 2D profilometric surface texture analysis, requiring a total revision of all current surface texture standards (ISO 4287, ISO 4288, ISO 1302, ISO 11562, ISO 12085, ISO 13565, etc.)

A new vocabulary is imposed:
* S filter: filter eliminating the smallest scale elements from the surface (or of the shortest wavelength for a linear filter)
* L filter: filter eliminating the largest scale elements from the surface (or of the longest wavelength for a linear filter)
* F operator: operator suppressing nominal form.
* S-L surface: surface obtained after S and L filtering. Equivalent to a roughness or waviness surface.
* S-F surface: surface obtained after S filtering and application of the F operator.
* Primary surface: surface obtained after S filtering.
* Nesting index: index corresponding to the cut-off wavelength of a linear filter, or to the scale of the structuring element of a morphological filter.

The new authorized filters are described in the series of technical specifications included in ISO/TS 16610. These filters include: the Gaussian filter, the spline filter, robust filters, morphological filters, wavelet filters, cascading filters, etc.

3D areal surface texture parameters

"'Generalities

3D parameters are written with the capital letter S (or V) followed by a suffix of one or two small letters. They are calculated on the entire surface and no more by averaging estimations calculated on a number of base lengths, as is the case for 2D parameters. In contrast with 2D naming conventions, the name of a 3D parameter does not reflect the filtering context. For example, "Sa" always appears regardless of the surface, whereas in 2D there is "Pa", "Ra" or "Wa" depending on whether the profile is a primary, roughness or waviness profile.

"'Height parameters

These parameters quantify the z axis perpendicular to the surface only.

"'Functional parameters

These parameters are calculated from the Abbott-Firestone curve obtained by the integration of the height distribution on the whole surface.

"'Parameters related to segmentation

These parameters are derived from a segmentation of the surface into motifs (dales and hills). Segmentation is carried out using the watersheds method.

3D surface texture measurement instruments

Part 6 of the standard divides the usable technologies into three families:

# Topographical instruments: contact and non-contact 3D profilometers, interferential and confocal microscopes, structured light projectors, stereoscopic microscopes, etc.
# Profilometric instruments: contact and non-contact 2D profilometers, line triangulation lasers, etc.
# Instruments functioning by integration: pneumatic measurement, capacitive, by optical diffusion, etc.

and defines each of these technologies.

Next, the standard explores a number of these technologies in detail and dedicates two documents to each of them:

* Part 6xx: nominal characteristics of the instrument
* Part 7xx: calibration of the instrument

"'Contact profilometer

Parts 601 and 701 describe the contact profilometer, using a diamond point to measure the surface with the assistance of a lateral scanning device.

"'Chromatic confocal gauge

Part 602 describes this type of non-contact profilometer, incorporating a single point white light chromatic confocal sensor. The operating principle is based upon the chromatic dispersion of the white light source along the optical axis, via a confocal device, and the detection of the wavelength that is focused on the surface by a spectrometer.

References

* [http://www.iso.org/iso/en/CatalogueDetailPage.CatalogueDetail?CSNUMBER=42785&scopelist=PROGRAMME ISO 25178 on the ISO Web site]
* [http://www.qualitymag.com/QUAL/Home/Files/PDFs/New3DParametersandFiltrationTechniquesforSurfaceMetrology.pdf "New 3D parameters and filtration techniques for surface metrology", François Blateyron, Quality Magazine White Paper]
* ISO/TS 16610-1 : Geometric Product Specifications (GPS): Filtration – Part 1: Overview and basic concepts
* ISO/TS 14406 : Geometric Product Specifications (GPS): Extraction


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Iso 25178 — désigne un ensemble de normes internationales définissant l’analyse des états de surface surfaciques (appelés aussi états de surface 3D). Cette norme en plusieurs parties a été rédigée par le groupe de travail WG16 au sein du comité technique… …   Wikipédia en Français

  • ISO 25178 — désigne un ensemble de normes internationales définissant l’analyse des états de surface surfaciques (appelés aussi états de surface 3D). Cette norme en plusieurs parties a été rédigée par le groupe de travail WG16 au sein du comité technique… …   Wikipédia en Français

  • EN ISO 25178 — DIN EN ISO 25178 Bereich Geometrische Produktspezifikation (GPS) Titel Oberflächenbeschaffenheit: Flächenhaft Kurzbe …   Deutsch Wikipedia

  • Iso 216 — Dimensions ISO 216 (mm × mm) Séries A A0 841 × 1189 A1 594 × 841 A2 420 × 594 A3 297 × 420 A4 210 × 297 A5 148 × 210 A6 …   Wikipédia en Français

  • ISO 3166-1 — est une des parties de la norme ISO 3166. Publiée pour la première fois en 1974 par l’ISO, elle attribue 3 codes pour les pays du monde : ISO 3166 1 alpha 2 : codes à deux lettres pour de nombreuses applications, notamment les domaines… …   Wikipédia en Français

  • ISO 4217 — (ИСО 4217) Коды для представления валют и фондов Codes for the representation of currencies and funds  (англ.) Codes pour la représentation des monnaies et types de fonds  (фр.) …   Википедия

  • ISO 3166-1 — ISO 3166 1  часть стандарта ISO 3166, содержащая коды названий стран и подчинённых территорий. Впервые опубликована в 1974 году. Определяет три разных кода для каждой страны: ISO 3166 1 alpha 2 (англ.)русск., двухбуквенная система …   Википедия

  • ISO 8601 — Data elements and interchange formats – Information interchange – Representation of dates and times is an international standard covering the exchange of date and time related data. It was issued by the International Organization for… …   Wikipedia

  • ISO/CEI 8859 — ISO 8859 ISO 8859, également appelée plus formellement ISO/CEI 8859, est une norme commune de l ISO et de la CEI de codage de caractères sur 8 bits pour le traitement informatique du texte. Le standard est divisé en parties numérotées publiées… …   Wikipédia en Français

  • ISO/IEC 8859 — ISO 8859 ISO 8859, également appelée plus formellement ISO/CEI 8859, est une norme commune de l ISO et de la CEI de codage de caractères sur 8 bits pour le traitement informatique du texte. Le standard est divisé en parties numérotées publiées… …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”