Inrush current limiter


Inrush current limiter

An inrush current limiter is a component used to limit inrush current. Negative temperature coefficient (NTC) thermistors and fixed resistors are often used for this. Less often, other components are also used.

The inrush current limiter is placed in series with the circuit whose inrush current needs to be limited.

Thermistor

A thermistor's resistance is initially high. When the equipment is turned on, the thermistor's resistance limits the initial current. Current flow heats the thermistor, and when hot its resistance is a lower value, allowing most of the input voltage to be appear on the following circuit. It is inherently impossible for 100% of supply voltage to appear on the following circuit, as the thermistor must continue to dissipate power to stay hot and therefore low resistance.

* Inrush current limiting thermistors are typically disk shaped, with two radial leads on one side.
* Their power handling is proportional to their size.
* They are rated according to their resistance at room temperature.

Fixed resistor

Fixed resistors are also widely used to limit inrush current. These are inherently less efficient, since the resistance never falls from the value required to limit the inrush current. Consequently they are generally chosen for lower power circuitry, where the additional ongoing power waste is minor. Inrush limiting resistors are much cheaper than thermistors. They are found in more or less all CFL lamps (light bulbs).

Applications

A typical application of inrush current limiters is in the input stage of non-Power Factor Corrected switching supplies, to reduce the initial surge of current from the line input to the filter capacitors.

References

* [http://www.ametherm.com/Inrush_Current/welcome.html Inrush Current Limiters] Description - Application Notes and Inrush Energy Calculator
* [http://www.rtie.com/ntc/surggard.htm RTI Electronics] makers of Sure-Gard Inrush Current Limiters
* [http://www.epcos.com/ EPCOS] ' [http://www.epcos.com/web/generator/Web/Sections/ProductCatalog/NonlinearResistors/NTCThermistors/ApplicationNotes/02__InrushCurrrentLimitingAN2/PDF__InrushCurrentLimiting__AN2,property=Data__en.pdf;/PDF_InrushCurrentLimiting_AN2.pdf Application notes] on Inrush Current Limiters

See also

* Soft start


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Inrush current — or input surge current refers to the maximum, instantaneous input current drawn by an electrical device when first turned on. For example, incandescent light bulbs have high inrush currents until their filaments warm up and their resistance… …   Wikipedia

  • Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… …   Wikipedia

  • Soft start — is an electronics term describing any circuit which is reduces excess current flow during initial power up.Need for soft startMany electronic devices will consume a large initial current when first turned on (i.e. Inrush current) that can cause… …   Wikipedia

  • Electronic component — Various components An electronic component is a basic electronic element and may be available in a discrete form having two or more electrical terminals (or leads). These are intended to be connected together, usually by soldering to a printed… …   Wikipedia

  • Motor soft starter — Examples of motor soft starters [1] A motor soft starter is a device used with AC electric motors to temporarily reduce the load and torque in the powertrain of the motor during startup. This reduces the mechanical stress on the motor and shaft,… …   Wikipedia

  • Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback …   Wikipedia

  • Hot swapping — and hot plugging are terms used to separately describe the functions of replacing system components; hot swapping describes changing components like fans and power supplies which do not interact with the system software, while hot plugging… …   Wikipedia

  • пусковой реактор — Токоограничивающий реактор, предназначенный для пуска электродвигателей [ГОСТ 18624 73] EN motor starting reactor reactor connected in series with a motor to limit the inrush current during the motor starting operation [IEC 60076 6, ed. 1.0 (2007 …   Справочник технического переводчика


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.