Lean burn

Lean burn

Lean burn refers to the use of lean mixtures in an internal combustion engine. The air-fuel ratios can be as high as 65:1, so the mixture has considerably less fuel in comparison to the stoichiometric combustion ratio (14.7:1 for petrol for example).

Contents

Principle

A lean burn mode is a way to reduce throttling losses. An engine in a typical vehicle is sized for providing the power desired for acceleration, but must operate well below that point in normal steady-speed operation. Ordinarily, the power is cut by partially closing a throttle. However, the extra work done in pumping air through the throttle reduces efficiency. If the fuel/air ratio is reduced, then lower power can be achieved with the throttle closer to fully open, and the efficiency during normal driving (below the maximum torque capability of the engine) can be higher.

The engines designed for lean burning can employ higher compression ratios and thus provide better performance, efficient fuel use and low exhaust hydrocarbon emissions than those found in conventional petrol engines. Ultra lean mixtures with very high air-fuel ratios can only be achieved by direct injection engines.

The main drawback of lean burning is that a complex catalytic converter system is required to reduce NOx emissions. Lean burn engines do not work well with modern 3-way catalytic converter—which require a pollutant balance at the exhaust port so they can carry out oxidation and reduction reactions—so most modern engines run at or near the stoichiometric point. Alternatively, ultra-lean ratios can reduce NOx emissions[citation needed].

Chrysler Electronic Lean Burn

From 1976 through 1989, Chrysler equipped many vehicles with their Electronic Lean Burn (ELB) system, which consisted of a spark control computer and various sensors and transducers. The computer adjusted spark timing based on manifold vacuum, engine speed, engine temperature, throttle position over time, and incoming air temperature. Engines equipped with ELB used fixed-timing distributors without the traditional vacuum and centrifugal timing advance mechanisms. The ELB computer also directly drove the ignition coil, eliminating the need for a separate ignition module.

ELB was produced in both open-loop and closed-loop variants; the open-loop systems produced exhaust clean enough for many vehicle variants so equipped to pass 1976 and 1977 US Federal emissions regulations, and Canadian emissions regulations through 1980, without a catalytic converter. The closed-loop version of ELB used an Oxygen sensor and a feedback carburetor, and was phased into production as emissions regulations grew more stringent starting in 1981, but open-loop ELB was used as late as 1990 in markets with lax emissions regulations, on vehicles such as the Mexican Chrysler Spirit. The spark control and engine parameter sensing and transduction strategies introduced with ELB remained in use through 1995 on Chrysler vehicles equipped with throttle-body fuel injection[citation needed].

Heavy-duty gas engines

Lean burn concepts are often used for the design of heavy-duty natural gas, biogas, and liquefied petroleum gas (LPG) fuelled engines. These engines can either be full-time lean burn, where the engine runs with a weak air-fuel mixture regardless of load and engine speed, or part-time lean burn (also known as "lean mix" or "mixed lean"), where the engine runs lean only during low load and at high engine speeds, reverting to a stoichiometric air-fuel mixture in other cases.

Heavy-duty lean burn gas engines admit as much as 75% more air than theoretically needed for complete combustion into the combustion chambers. The extremely weak air-fuel mixtures lead to lower combustion temperatures and therefore lower NOx formation. While lean-burn gas engines offer higher theoretical thermal efficiencies, transient response and performance may be compromised in certain situations. Lean burn gas engines are almost always turbocharged, resulting high power and torque figures not achieveable with stoichiometric engines due to high combustion temperatures.

Heavy duty gas engines may employ precombustion chambers in the cylinder head. A lean gas and air mixture is first highly compressed in the main chamber by the piston. A much richer, though much lesser volume gas/air mixture is introduced to the precombustion chamber and ignited by spark plug. The flame front spreads to the lean gas air mixture in the cylinder.

This two stage lean burn combustion produces low NOx and no particulate emissions. Thermal efficiency is better as higher compression ratios are achieved.

Manufacturers of heavy-duty lean burn gas engines include GE Jenbacher, MAN Diesel & Turbo, Wärtsilä, Mitsubishi Heavy Industries and Rolls-Royce plc.

Honda lean burn systems

One of the newest lean-burn technologies available in automobiles currently in production uses very precise control of fuel injection, a strong air-fuel swirl created in the combustion chamber, a new linear air-fuel sensor (LAF type O2 sensor) and a lean-burn NOx catalyst to further reduce the resulting NOx emissions that increase under "lean-burn" conditions and meet NOx emissions requirements.

This stratified-charge approach to lean-burn combustion means that the air-fuel ratio isn't equal throughout the cylinder. Instead, precise control over fuel injection and intake flow dynamics allows a greater concentration of fuel closer to the spark plug tip (richer), which is required for successful ignition and flame spread for complete combustion. The remainder of the cylinders' intake charge is progressively leaner with an overall average air:fuel ratio falling into the lean-burn category of up to 22:1.

The older Honda engines that used lean burn (not all did) accomplished this by having a parallel fuel and intake system that fed a pre-chamber the "ideal" ratio for initial combustion. This burning mixture was then opened to the main chamber where a much larger and leaner mix then ignited to provide sufficient power. During the time this design was in production this system (CVCC, Compound Vortex Controlled Combustion) primarily allowed lower emissions without the need for a catalytic converter. These were carbureted engines and the relative "imprecise" nature of such limited the MPG abilities of the concept that now under MPI (Multi-Port fuel Injection) allows for higher MPG too.

The newer Honda stratified charge (lean burn engines) operate on air-fuel ratios as high as 22:1. The amount of fuel drawn into the engine is much lower than a typical gasoline engine, which operates at 14.7:1—the chemical stoichiometric ideal for complete combustion when averaging gasoline to the petrochemical industries' accepted standard of C6H8.

This lean-burn ability by the necessity of the limits of physics, and the chemistry of combustion as it applies to a current gasoline engine must be limited to light load and lower RPM conditions. A "top" speed cut-off point is required since leaner gasoline fuel mixtures burn slower and for power to be produced combustion must be "complete" by the time the exhaust valve opens.

Applications

Honda lean burn engine applications
Unladen weight Fuel consumption, Japan 10-15 mode Fuel tank capacity Range
Years Model Engine kg lbs L/100 km km/L mpg UK mpg US L gal UK gal US km mile Notes
1991–95 Civic ETi D15B 930 2050 4.8 20.8 59 49 45 9.9 11.9 938 583 5spd manual, 3dr hatch, VTEC-E[1]
1995–00 Civic VTi D15B 1010 2226 5.0 20.0 56 47 45 9.9 11.9 900 559 5spd manual, 3dr hatch, 3 stage VTEC[2]
1995–00 Civic Vi D15B 1030 2226 5.3 18.9 53 44 45 9.9 11.9 849 528 5spd manual, 5dr sedan, 3 stage VTEC[3]

Toyota lean burn engines

The lean burn versions of the 1587cc 4A-FE and 1762cc 7A-FE 4 cylinder engines have 2 inlet and 2 exhaust valves per cylinder. Toyota uses a set of butterflies to restrict flow in every second inlet runner during lean burn operation. This creates a large amount of swirl in the combustion chamber. Injectors are mounted in the head, rather than conventionally in the intake manifold. Compression ratio 9.5:1.[4] The 1998cc 3S-FSE engine is a direct injection petrol lean burn engine. Compression ratio 10:1.[5]

Applications

Toyota lean burn engine applications
Unladen weight Fuel consumption, Japan 10-15 mode Fuel tank capacity Range
Years Model Engine kg lbs L/100 km km/L mpg UK mpg US L gal UK gal US km mile Notes
1994–96 Carina SG-i SX-i 4A-FE 1040 2292 5.6 17.6 50 41 60 13.2 15.9 1056 656 5spd manual[6]
1994–96 Carina SG-i SX-i 7A-FE 1040 2292 5.6 17.6 50 41 60 13.2 15.9 1056 656 5spd manual[6]
1996–01 Carina Si 7A-FE 1120 2468 5.5 18.0 51 42 60 13.2 15.9 1080 671 5spd manual[6]
1996–00 Corona Premio E 7A-FE 1120 2468 5.5 18.0 51 42 60 13.2 15.9 1080 671 5spd manual[7]
1998–00 Corona Premio G 3S-FSE 1200 2645 5.8 17.2 49 41 60 13.2 15.9 1034 643 Auto[8]
1996–97 Caldina FZ CZ 7A-FE 1140 2513 5.6 17.6 50 41 60 13.2 15.9 1056 656 5spd manual[9]
1997–02 Caldina E 7A-FE 1200 2645 5.6 17.6 50 41 60 13.2 15.9 1056 656 5spd manual[10]
1997–02 Spacio 7A-FE Auto[11]

Nissan lean burn engines

Nissan QG engines are a lean-burn aluminum DOHC 4-valve design with variable valve timing and optional NEO Di direct injection. The 1497cc QG15DE has a Compression ratio of 9.9:1[12] and 1769cc QG18DE 9.5:1.[13]

Applications

Nissan lean burn engine applications
Unladen weight Fuel consumption, Japan 10-15 mode Fuel tank capacity Range
Years Model Engine kg lbs L/100 km km/L mpg UK mpg US L gal UK gal US km mile Notes
1998–01 Sunny QG15DE 1060 2865 5.3 18.9 53 44 50 11 13.2 943 586 5spd manual, 4dr sedan[12]
1998–01 Bluebird QG18DE 1180 2600 5.8 17.2 49 41 60 13.2 15.9 1035 643 5spd manual, 4dr sedan[14]
1998–01 Primera QG18DE 1180 2600 5.8 17.2 49 41 60 13.2 15.9 1035 643 5spd manual, 4dr sedan[15]
1998–01 Avenir Salut QG18DE 1300 2865 6.7 14.9 42 35 60 13.2 15.9 896 556 5spd manual, 5dr wagon[13]

Mitsubishi Vertical Vortex (MVV)

In 1991, Mitsubishi developed and began producing the MVV (Mitsubishi Vertical Vortex) lean burn system first used in Mitsubishi's 1.5 L 4G15 straight-4 single-overhead-cam 1,468-cc engine. The vertical vortex engine has an idle speed of 600 rpm and a compression ratio of 9.4:1 compared with respective figures of 700 rpm and 9.2:1 for the conventional version. The lean-burn MVV engine can achieve complete combustion with an air-fuel ratio as high as 25:1, this boasts a 10-20% gain in fuel economy (on the Japanese 10-mode urban cycle) in bench tests compared with its conventional MPI powerplant of the same displacement, which means lower CO2 emissions.[16][17]

The heart of the Mitsubishi's MVV system is the linear air-fuel ratio exhaust gas oxygen sensor. Compared with standard oxygen sensors, which essentially are on-off switches set to a single air/fuel ratio, the lean oxygen sensor is more of a measurement device covering the air/fuel ratio range from about 15:1 to 26:1.[17]

To speed up the otherwise slow combustion of lean mixtures, the MVV engine uses two intake valves and one exhaust valve per cylinder. The separate specially shaped (twin intake port design) intake ports are the same size, but only one port receives fuel from an injector. This creates two vertical vortices of identical size, strength and rotational speed within the combustion chamber during the intake stroke: one vortex of air, the other of an air/fuel mixture. The two vortices also remain independent layers throughout most of the compression stroke.[16][17]

Near the end of the compression stroke, the layers collapse into uniform minute turbulences, which effectively promote lean-burn characteristics. More importantly, ignition occurs in the initial stages of breakdown of the separate layers while substantial amounts of each layer still exist. Because the spark plug is located closer to the vortex consisting of air/fuel mixture, ignition arises in an area of the pentroof-design combustion chamber where fuel density is higher. The flame then spreads through the combustion chamber via the small turbulences. This provides stable combustion even at normal ignition-energy levels, thereby realizing lean burn.[16][17]

The engine computer stores optimum air fuel ratios for all engine-operating conditions - from lean (for normal operation) to richest (for heavy acceleration) and all points in between. Full-range oxygen sensors (used for the first time) provide essential information that allows the computers to properly regulate fuel delivery.[17]

Diesel engines

All diesel engines can be considered to be lean burning with respect to the total volume, however the fuel and air is not well mixed before the combustion. Most of the combustion occurs in rich zones around small droplets of fuel. Locally rich combustion like this is a source of NOx and particles.

See also

Footnotes

Citations

  1. ^ "91CivicHatch", auto.vl.ru japanese car specification website
  2. ^ "95CivicHatch", auto.vl.ru japanese car specification website
  3. ^ "95CivicSedan", auto.vl.ru japanese car specification website
  4. ^ "Toyota Carina Specifications", auto.vl.ru japanese car specification website
  5. ^ "Toyota Corona Premio G", auto.vl.ru japanese car specification website
  6. ^ a b c "Toyota Carina", auto.vl.ru japanese car specification website
  7. ^ "Toyota Corona Premio", auto.vl.ru japanese car specification website
  8. ^ "Toyota Corona Premio G", auto.vl.ru japanese car specification website
  9. ^ "Toyota Caldina", auto.vl.ru japanese car specification website
  10. ^ "Toyota Caldina", Toyota NZ website
  11. ^ "Toyota Spacio", Toyota NZ website
  12. ^ a b "Nissan Sunny", auto.vl.ru japanese car specification website
  13. ^ a b "Nissan Avenir", auto.vl.ru japanese car specification website
  14. ^ "Nissan Bluebird", auto.vl.ru japanese car specification website
  15. ^ "Nissan Primera", auto.vl.ru japanese car specification website
  16. ^ a b c "Engine Technology", Mitsubishi Motors South Africa website
  17. ^ a b c d e "Honda can't sell lean-burn in California", Joel D. Pietrangelo & Robert Brooks, Ward's Auto World, September 1991

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • lean-burn — leanˈ burnˈ adjective Of, using or relating to a fuel air mixture in which the fuel component is relatively low, so reducing the amount of fuel used and pollution produced • • • Main Entry: ↑lean * * * adj. of or relating to an internal… …   Useful english dictionary

  • lean-burn — adjective (of an internal combustion engine) designed to run on a lean mixture to reduce pollution …   English new terms dictionary

  • lean-burn engine — An engine which uses a lean mixture of fuel and air to increase fuel economy and reduce exhaust emissions. Also see CACIS …   Dictionary of automotive terms

  • Gasoline direct injection — In internal combustion engines, gasoline direct injection (GDI), also known as petrol direct injection or direct petrol injection, is a variant of fuel injection employed in modern two stroke and four stroke gasoline engines. The gasoline is… …   Wikipedia

  • Catalytic converter — A catalytic converter (colloquially, cat or catcon ) is a device used to reduce the toxicity of emissions from an internal combustion engine. First widely introduced on series production automobiles in the US market for the 1975 model year to… …   Wikipedia

  • Oxygen sensor — Contents 1 Automotive applications 1.1 Function of a lambda probe 1.2 The probe …   Wikipedia

  • Royal Enfield — Infobox Defunct Company company name = Enfield Cycle Co. Ltd. company successor = Royal Enfield Motors Ltd. (formerly Enfield of India) foundation = 1893, as Enfield Manufacturing Co. Ltd. defunct = 1970 fate = Ended production. location =… …   Wikipedia

  • Royal Enfield Motors — is a motorcycle manufacturing company based in Chennai, India. Infobox Company company name = Royal Enfield Motors Ltd. company company type = Private company slogan = Made Like A Gun foundation = 1955 as Enfield India location = key people = num …   Wikipedia

  • Rolls-Royce marine diesel engines — are manufactured by Rolls Royce plc and cover five ranges of diesel engines for the marine sector.There are three Bergen and two Crossley Pielstick ranges with power outputs in the range 1.2MW to 15MW. Bergen RangeThe Bergen marine diesel ranges… …   Wikipedia

  • Honda D engine — D16Y4 Engine D16Z6 Engine Lightly Customized …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”