Brake fade

Brake fade

Vehicle braking system fade, or brake fade is the reduction in stopping power that can occur after repeated application of the brakes, especially in high load or high speed conditions. Brake fade can be a factor in any vehicle that utilizes a friction braking system including automobiles, trucks, motorcycles, airplanes, even bicycles.

Brake fade is caused by a buildup of heat in the braking surfaces and the subsequent changes and reactions in the brake system components and can be experienced with both drum brakes and disk brakes. Loss of stopping power, or fade, can be caused by friction fade, mechanical fade, or fluid fade. Brake fade can be significantly reduced by appropriate equipment and materials design and selection.

Brake fade occurs most often during high performance driving or when going down a long, steep hill. Owing to their configuration this is more prevalent in drum brakes. Disk brakes are much more resistant to brake fade and have come to be a standard feature in front brakes for most vehicles.

Causes of brake fade

The reduction of friction termed brake fade is caused when the temperature reaches the "kneepoint" on the temperature-friction curve. ["All brake lining is cured under mechanical pressure following a heating & cooling curve, heating the friction material up to 450°F to "cure" (cross-link) the phenolic resin thermoset polymers: There is no melting of the binding resins, because phenolic resins are thermoset, not thermoplastic"] In this form of fade, the brake pedal feels firm but there is reduced stopping ability. Fade can also be caused by the brake fluid boiling, with attendant release of compressible gases. In this type of fade, the brake pedal feels "spongy". This condition is worsened when there are contaminants in the fluid, such as water, which most types of brake fluids are prone to absorbing to varying degrees. For this reason brake fluid replacement is standard maintenance.

Fade in drum brakes

High sensitivity of drum brakes due to small changes in frictioncoefficient can severely affect their performance. Fadeat high temperatures, caused by dissipating kinetic energy whileslowing a vehicle can cause loss of braking while an increase cancause lock-up. Because fade may not occur simultaneously on allwheels, differential braking can cause a vehicle to swerve. As fadeincreases, typically while descending long steep grades, brakes on allwheels may fail and cause a runaway. High sensitivity to changes infriction coefficient is inherent to expanding-shoe drum brakes, thetype formerly used on most cars and still used on many trucks,especially for rear axles and trailers.

The inherent design problem of drum brakes, from which their sensitivityto small changes in friction coefficient arises, is self energizing
servo by which brake shoes, when pressed against the drum, pushthemselves into contact by their own friction, giving responses fromlock-up to complete failure. For example, on damp mornings, drumbrakes can lock on first application, skidding to a stop even afterthe brake pedal has been released. This occurs because servo or
positive feedback magnifies small changes in friction coefficient.In contrast, with disk brakes, that have no servo effect, these smallchanges in friction coefficient are hardly noticeable.

Brake failure was also caused by brake drum thermal expansion in whichbrake shoe clearance had become excessive from wear. This was remedied inthe 1950s by self adjusting "brakes". [http://digital.lib.msu.edu/collections/sesquicentennial/se/se-38.pdf?CFID=1834320&CFTOKEN=86763474 "Spartan Engineering 1959"] ; Disk Brakes; accessed 2007-02-26] Maladjustment with wear is still a factor in trucks that use drum air brakes. http://www.roadranger.com/ecm/groups/public/@pub/@roadranger/documents/content/rr_axag-0300.pdf; Dana Spicer Trailer Axles & Brakes; Application Guide AXAG-0300 March 2006; See "Brake Fade" in glossary; accessed 2007-02-26] Another explanation for brake failure was that heated brake shoes evaporated to generate gas that separate them from the drum. When experiencing brake fade one could readily imagine such effects even though they are physically impossible, considering the volume of gas required for such an effect, the
gas bearing needing replenishment as fast as the disk moves, it having no gas on its surface when entering the interface. After cooling, faded brakes perform as well as before with no visible change to brake shoes. In contrast, disk brakes, using much the same materials, operate well even with glowing hot disks [http://www.threeplanes.net/toolsteel.html (color vs. temperature)] '

Long dual-tire skid marks on highways, made by trucks with drumbrakes, are visible examples of non-linearity between brake responseand pedal pressure. Large trucks still use drum brakes because theyare economical and fit easily where an equivalent disk brake wouldnot. More recently disk brakes for trucks have been promoted listingfeatures such as no fade, made possible in the absence of brake servo. [ [http://www.roadranger.com/Roadranger/productssolutions/brakes/airdiscbrakes/index.htm Air Disc Brakes ] ] Their disk surfaces also have no gas venting features.

Railroads

Railroads have been using disk brakes on passenger cars for more than 60 years, but coupled with a "Rolokron" anti-lock system to avoid the creation of "flat spots" (or “"square wheels"”) when wheels locks and skid on the rail surface (audible as rhythmic "bang-bang-bang" noise as a train goes by). Usually, brake disks are installed in the center of the axle, but in some applications (such as Bombardier Bi Level commuter cars), only one disk is used, mounted on the axle end outside the truck frame. High speed trains (such as the TGV)may use four disks per axle.

Freight cars (and some passenger cars like multiple-unit cars whose traction motors do not yield room on axles to allow the placement of disk brakes) are equipped with "clasp brakes" which directly grab the rolling surface of the wheels (much like the old horse buggy brakes of yersteryear). Such brakes are far less susceptible to locking than disk brakes so freight cars are not equipped with anti-lock systems.

Controlling fade through driving technique

Brake fade and rotor warping can be reduced through proper braking technique; When running down a long downgrade that would require braking simply select a lower gear (for automatic transmissions this may necessitate a brief application of the throttle after selecting the gear). Also, periodic, rather than continuous application of the brakes will allow them to cool between applications. Continuous light application of the brakes can be particularly destructive in both wear and adding heat to the brake system. Finally, new brakes should be used as gently as possible for the first 100 miles or so to "break them in" and eliminate green fade.

Brake modification to reduce fade

High performance brake components provide enhanced stopping power by improving friction while reducing brake fade. Improved friction is provided by lining materials that have a higher coefficient of friction than stock brake pads while brake fade is reduced through the use of more expensive binding resins with a higher melting point along with slotted, drilled, or dimpled rotors that reduce the gaseous boundary layer in addition to providing enhanced heat dissipation. Heat buildup in brakes can be further addressed by body modifications that direct cold air to the brakes.

The "gaseous boundary layer" is an hot rod mechanics explanation for failing self servo effect of drum brakes because it felt like a brick under the brake pedal when it occurred. To counterthis effect, brake shoes were drilled and slotted to vent gas. In spite of that, drum brakes were abandoned for thier self servo effect. Disks do not have that because application force is applied at right angles to the resultin braking force. There is no interaction.

Adherents of gas emission have carried that belief to motorcycles, bycycles and "sports" cars whileall other disk brake users from the same automotive companies have no holes through the faces of theirdisks although internal radial air passages are used. Vents to release gas have not beenfound on railway, aircraft and passenger car brakes because there is no gas to vent. Meanwhile heavy trucks still use drum brakes because they offer more heat dissipation than disks that would fit in the same space. Rialways have never used internal expanding drum brakes because they cause skidding, causing expensive flat spots on steel wheels.

Both disc and drum brakes can be improved by any technique that removes heat from the braking surfaces.

Drum brake fade can be reduced and overall performance enhanced somewhat by an old "hot rodder" technique of drum drilling. A carefully chosen pattern of holes is drilled through the drum working section; drum rotation centrifugally pumps a small amount air through the shoe to drum gap, removing heat; fade caused by water-wet brakes is reduced since the water is centrifugally driven out; and some brake-material dust exits the holes. Brake drum drilling requires careful detailed knowledge of brake drum physics and is an advanced technique probably best left to professionals. There are performance-brake shops that will make the necessary modifications safely.The Bugatti Veyron for example has turbine cooled brakes that reduce fade to almost nothing considering the speeds it is braking from.

Brake fade caused by overheating brake fluid can also be reduced through the use of thermal barriers that are placed between the brake pad and the brake caliper piston, thus reducing the transfer of heat from the pad to the caliper and hydraulic brake fluid. Some high-performance racing calipers already include such brake heat shields made from titanium or ceramic materials. It is also possible to purchase aftermarket titanium brake heat shields that will fit your existing brake system to provide protection from brake heat.

ee also

*Disc brake

References and sources

* http://www.tirerack.com/brakes/tech/techpage.jsp?techid=78&currentpage=87 Tire Rack article accessed 2006-10-23
* [http://www.FMSI.org Friction Material Standards Institute]
* [http://tispeed.com/index.php?main_page=page&id=1&chapter=1 Titanium Brake Heat Shield Technical Info]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • brake-fade — brakeˈ fade noun A decrease of efficiency in a brake sometimes resulting in complete absence of stopping power • • • Main Entry: ↑brake …   Useful english dictionary

  • brake fade — Auto. a gradual loss of braking power resulting from decreased friction between the lining and the drum or disc of the brake and usually caused by overheating. Also called fade. * * * brake fade, a loss of braking power in a motor vehicle …   Useful english dictionary

  • brake fade — Auto. a gradual loss of braking power resulting from decreased friction between the lining and the drum or disc of the brake and usually caused by overheating. Also called fade. * * * …   Universalium

  • brake fade — Reduction or loss in braking force due to loss of friction between brake shoes and drum (or brake pads and disc). Caused by heat buildup through repeated or prolonged brake application …   Dictionary of automotive terms

  • Fade — may refer to: *Fade (Blue Angel song), an obscure song by the band Blue Angel *Fade (Staind song), a song from Break the Cycle by alt rock band Staind *Fade (film), a cinematographic technique used in film *Fade (audio engineering), the gradual… …   Wikipedia

  • Brake lining — Brake linings are the consumable surfaces in braking systems, especially those used in vehicles.tructure and functionBrake linings are composed of a relatively soft but tough and heat resistant material with a high coefficient of dynamic friction …   Wikipedia

  • Brake pad — Brake pads are an important part of braking systems for all types of vehicles that are equipped with disc brakes. Brake pads are steel backing plates with friction material bound to the surface facing the brake disk.FunctionBrake pads convert the …   Wikipedia

  • fade — fadable, adj. fadedly, adv. fadedness, n. /fayd/, v., faded, fading, n. v.i. 1. to lose brightness or vividness of color. 2. to become dim, as light, or lose brightness of illumination. 3. to lose freshness, vigor, strength, or health: The tulips …   Universalium

  • brake disc type — A braking system that instead of using the conventional brake drum with internal brake shoes, uses a steel disc with caliper type lining application, when the brakes are applied, a section of lining on each side of the spinning disc is forced… …   Dictionary of automotive terms

  • fade — A gradual reduction in efficiency. See brake fade …   Dictionary of automotive terms

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”