Mud engineer

Mud engineer

A mud engineer (correctly called a Drilling Fluids Engineer, but most often referred to as the "Mud Man") works on an oil well or gas well drilling rig, and is responsible ensuring the properties of the drilling fluid, also known as drilling mud, are within designed specifications.

Contents

Use of mud

Mud is a vital part of drilling operations. It provides hydrostatic pressure on the borehole wall to prevent uncontrolled production of reservoir fluids, lubricates and cools the drill bit, carries the drill cuttings up to the surface, forms a "filter-cake" on the borehole wall to prevent drilling fluid invasion, provides an information medium for well logging, and helps the drilling by fracturing the rock from the jets in the bit. To fulfill these tasks effectively, the mud contains carefully chosen additives to control its chemical and rheological properties.

Drilling mud is usually a shear-thinning non-Newtonian fluid of variable viscosity. When it is under more shear, such as in the pipe to the bit and through the bit nozzles, viscosity is lower which reduces pumping-power requirements. When returning to the surface through the much roomier annulus it is under less shear stress and becomes more viscous, and hence better able to carry the rock cuttings. Bentonite is commonly used as an additive to control and maintain viscosity, and also has the additional benefit of forming a mud-cake (also known as a filter cake) on the bore-hole wall, preventing fluid invasion.[1]

Barite is commonly used to "weight" the mud to maintain adequate hydrostatic pressure down-hole. This is critical in a drilling operation to avoid a kick and ultimately a blowout from uncontrolled production of formation fluids. The "mud-pits" at the surface have their levels carefully monitored, since an increase in the mud level indicates a kick is taking place, and may require shutting in the well and circulating heavier weighted drilling mud to prevent further formation fluid or gas production.

Drilling fluid must be chemically compatible with the formations being drilled. Salinity must be chosen so as not to cause clay swelling or other problems. Mud can be "oil-based" or "water-based". In many areas oil-based muds are being phased out, as they are less environmentally friendly, although in some formations they are necessary because of chemical compatibility issues. Offshore rigs typically use synthetic oil based mud.

The Job

The mud engineer (or drilling fluids engineer) may be a university, college, or technical institute graduate, or may have no tertiary education at all, having gained experience working on rigs which could be over 10 years. On land, this experience would come from being a derrick hand, and offshore, the experience would come from being a pump man. Prior to working on his own, he has been on a special training course, known as "mud school", and often spends time working with a senior mud engineer to gain experience.

Prior to drilling a well, a "mud program" will be worked out according to the expected geology, in which products to be used, concentrations of those products, and fluid specifications at different depths are all predetermined. As the hole is drilled and gets deeper, more mud is required, and the mud engineer is responsible for making sure that the new mud to be added is made up to the required specifications. The chemical composition of the mud will be designed so as to stabilize the hole. It is sometimes necessary to completely change the mud to drill through a particular subsurface layer.

As drilling proceeds, the mud engineer will get information from other service providers such as the mud logger (mud logging technician) about progress through the geological zones, and will make regular physical and chemical checks on the drilling mud. In particular the Marsh funnel viscosity and the density are frequently checked. As drilling proceeds, the mud tends to accumulate small particles of the rocks which are being drilled through, and its properties change. It is the job of the mud engineer to specify additives to correct these changes, or to partially or wholly replace the mud when necessary. He or she must also keep an eye on the equipment which is used to pump the mud and to remove particles, and be prepared if the geologists' predictions are not entirely correct, or if other problems arise.

It is sometimes necessary to stabilize the wall of a borehole at a particular depth by pumping cement down through the mud system, and the mud engineer is sometimes in charge of this process.

The mud engineer is well supported by the mud supply company with computer aids and manuals dealing with all known problems and their solution, but it is his or her responsibility to get it right in a situation where mistakes can be very costly indeed.

A mud engineer's job may involve long shifts of over 12 hours a day. Typical offshore and foreign work schedules are four weeks working and four weeks off.

Important Fluid Properties

One of the most important mud properties is the mud weight (density). If the mud weight exceeds the fracture pressure of the formation, the formation may fracture and large quantities of mud are lost to it, in a situation referred to as lost circulation. These cracks can also cause water to seep into the well bore or into a hydrocarbon bearing zone, which would likely impede the ability of the formation to produce oil (or require the separation of large quantities of water).

Conversely, if the mud weight is too low it will have a hydrostatic pressure that is less than the formation pressure. This will cause pressurized fluid in the formation to flow into the wellbore and make its way to the surface. This is referred to as a formation "kick" and can lead to a potentially deadly blowout if the invading fluid reaches the surface uncontrolled.

Other important mud properties to be maintained are the YP (Yield Point) which determines the carrying capacity of the mud to carry the drill cuttings to the surface. Mud should be capable of forming a thin "mud cake" which forms a lining of the borehole walls.

Drilling Fluids Companies

Drilling fluids operations are often contracted to service companies, a trend commonly observed in the oil industry for most of it operations. The largest three companies for mud services are M-I SWACO (A Schlumberger Company), Baroid Drilling Fluids (Halliburton Oilfield Services), and Baker Hughes Drilling Fluids. There are, however, many smaller companies providing drilling fluid services as well. Independent companies can provide a localized knowledge, and quality services and mud products.

Further reading

  • ASME Shale Shaker Committee (2005) The Drilling Fluids Processing Handbook ISBN 0-7506-7775-9
  • Kate Van Dyke (1998) Drilling Fluids, Mud Pumps, and Conditioning Equipment
  • G. V. Chilingarian & P. Vorabutr (1983) Drilling and Drilling Fluids
  • G. R. Gray, H. C. H. Darley, & W. F. Rogers (1980) The Composition and Properties of Oil Well Drilling Fluids

See also

Notes

  1. ^ http://www.glossary.oilfield.slb.com/Display.cfm?Term=bentonite Schlumberger Oilfield Glossary – Bentonite

Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • mud engineer — noun A person overseeing the use and supply of drilling mud on a gas or oil well • • • Main Entry: ↑mud …   Useful english dictionary

  • mud engineer — gręžimo skiedinių inžinierius statusas T sritis profesijos apibrėžtis Inžinierius, kuris gręžimo skiedinius tiria laboratorijoje. atitikmenys: angl. drilling fluid engineer; mud engineer pranc. boueux, m; ingénieur de boues, m; ingénieur des… …   Inžinieriai, technikai ir technologai. Trikalbis aiškinamasis žodynėlis

  • mud engineer — gręžimo skiedinių inžinierius statusas T sritis profesijos apibrėžtis Inžinierius, kuris sudaro gręžimo skiedinių programą, tikrina, ar jie tinkamai naudojami, ar yra efektyvūs gręžimo metu, visada yra pasirengęs pakeisti gręžimo skiedinio… …   Inžinieriai, technikai ir technologai. Trikalbis aiškinamasis žodynėlis

  • Mud logging — Mud log in process. Well logging Gamma ray logging Spontaneous potential logging Resistivity logging Density logging …   Wikipedia

  • Mud Will Be Flung Tonight — Live album by Bette Midler Released 1985 Recorded Apri …   Wikipedia

  • Drilling mud — In geotechnical engineering, drilling mud, also known as spud mud (when beginning the drilling process), is a drilling fluid used to drill boreholes into the earth. Often used while drilling oil and natural gas wells and on exploration drilling… …   Wikipedia

  • drilling fluid engineer — gręžimo skiedinių inžinierius statusas T sritis profesijos apibrėžtis Inžinierius, kuris gręžimo skiedinius tiria laboratorijoje. atitikmenys: angl. drilling fluid engineer; mud engineer pranc. boueux, m; ingénieur de boues, m; ingénieur des… …   Inžinieriai, technikai ir technologai. Trikalbis aiškinamasis žodynėlis

  • drilling fluid engineer — gręžimo skiedinių inžinierius statusas T sritis profesijos apibrėžtis Inžinierius, kuris sudaro gręžimo skiedinių programą, tikrina, ar jie tinkamai naudojami, ar yra efektyvūs gręžimo metu, visada yra pasirengęs pakeisti gręžimo skiedinio… …   Inžinieriai, technikai ir technologai. Trikalbis aiškinamasis žodynėlis

  • 15th Engineer Battalion — Infobox Military Unit unit name=15th Engineer Battalion caption= 15th Engineer Battalion Crest dates= 1916 1919, 1940 1946, 1948 1962, 1966 1969, 1972 1991, 2008 country= United States allegiance= branch= United States Army type= Construction… …   Wikipedia

  • 805th Engineer Aviation Battalion (United States) — Infobox Military Unit unit name= 805th Engineer Aviation Battalion caption= 805th Memorial at National Museum of the US Air Force dates= 1941 1946 country= United States allegiance= branch= USAAF type= Engineer role= Constructed fighter and… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”