Bipolar transistor biasing

Bipolar transistor biasing

Bipolar transistor amplifiers must be properly biased to operate correctly. In circuits made with individual devices (discrete circuits), biasing networks consisting of resistors are commonly employed. Much more elaborate biasing arrangements are used in integrated circuits, for example, bandgap voltage references and current mirrors.

The operating point of a device, also known as bias point, quiescent point, or Q-point, is the point on the output characteristics that shows the DC collector–emitter voltage (Vce) and the collector current (Ic) with no input signal applied. The term is normally used in connection with devices such as transistors.

Contents

Bias circuit requirements

Signal requirements for Class A amplifiers

For analog operation of a Class A amplifier, the Q-point is placed so the transistor stays in active mode (does not shift to operation in the saturation region or cut-off region) when input is applied. For digital operation, the Q-point is placed so the transistor does the contrary - switches from "on" to "off" state. Often, Q-point is established near the center of active region of transistor characteristic to allow similar signal swings in positive and negative directions. Q-point should be stable. In particular, it should be insensitive to variations in transistor parameters (for example, should not shift if transistor is replaced by another of the same type), variations in temperature, variations in power supply voltage and so forth. The circuit must be practical: easily implemented and cost-effective.

Thermal considerations

At constant current, the voltage across the emitter–base junction VBE of a bipolar transistor decreases 2 mV (silicon) and 1.8mV (germanium) for each 1 °C rise in temperature (reference being 25 °C). By the Ebers–Moll model, if the base–emitter voltage VBE is held constant and the temperature rises, the current through the base–emitter diode IB will increase, and thus the collector current IC will also increase. Depending on the bias point, the power dissipated in the transistor may also increase, which will further increase its temperature and exacerbate the problem. This deleterious positive feedback results in thermal runaway.[1] There are several approaches to mitigate bipolar transistor thermal runaway. For example,

  • Negative feedback can be built into the biasing circuit so that increased collector current leads to decreased base current. Hence, the increasing collector current throttles its source.
  • Heat sinks can be used that carry away extra heat and prevent the base–emitter temperature from rising.
  • The transistor can be biased so that its collector is normally less than half of the power supply voltage, which implies that collector–emitter power dissipation is at its maximum value. Runaway is then impossible because increasing collector current leads to a decrease in dissipated power; this notion is known as the half-voltage principle.

The circuits below primarily demonstrate the use of negative feedback to prevent thermal runaway.

Types of bias circuit for Class A amplifiers

The following discussion treats five common biasing circuits used with Class A bipolar transistor amplifiers:

  1. Fixed bias
  2. Collector-to-base bias
  3. Fixed bias with emitter resistor
  4. Voltage divider bias
  5. Emitter bias

Fixed bias (base bias)

Fixed bias (Base bias)

This form of biasing is also called base bias. In the example image on the right, the single power source (for example, a battery) is used for both collector and base of a transistor, although separate batteries can also be used.

In the given circuit,

Vcc = IBRB + Vbe

Therefore,

IB = (Vcc - Vbe)/RB

For a given transistor, Vbe does not vary significantly during use. As Vcc is of fixed value, on selection of RB, the base current IB is fixed. Therefore this type is called fixed bias type of circuit.

Also for given circuit,

Vcc = ICRC + Vce

Therefore,

Vce = Vcc - ICRC

The common-emitter current gain of a transistor is an important parameter in circuit design, and is specified on the data sheet for a particular transistor. It is denoted as β on this page.

Because

IC = βIB

we can obtain IC as well. In this manner, operating point given as (Vce,IC) can be set for given transistor.

Merits:

  • It is simple to shift the operating point anywhere in the active region by merely changing the base resistor (RB).
  • A very small number of components are required.

Demerits:

  • The collector current does not remain constant with variation in temperature or power supply voltage. Therefore the operating point is unstable.
  • Changes in Vbe will change IB and thus cause RE to change. This in turn will alter the gain of the stage.
  • When the transistor is replaced with another one, considerable change in the value of β can be expected. Due to this change the operating point will shift.
  • For small-signal transistors (e.g., not power transistors) with relatively high values of β (i.e., between 100 and 200), this configuration will be prone to thermal runaway. In particular, the stability factor, which is a measure of the change in collector current with changes in reverse saturation current, is approximately β+1. To ensure absolute stability of the amplifier, a stability factor of less than 25 is preferred, and so small-signal transistors have large stability factors.[citation needed]

Usage:

Due to the above inherent drawbacks, fixed bias is rarely used in linear circuits (i.e., those circuits which use the transistor as a current source). Instead, it is often used in circuits where transistor is used as a switch. However, one application of fixed bias is to achieve crude automatic gain control in the transistor by feeding the base resistor from a DC signal derived from the AC output of a later stage.

Collector-to-base bias

Collector-to-base bias

This configuration employs negative feedback to prevent thermal runaway and stabilize the operating point. In this form of biasing, the base resistor RB is connected to the collector instead of connecting it to the DC source Vcc. So any thermal runaway will induce a voltage drop across the RC resistor that will throttle the transistor's base current.

From Kirchhoff's voltage law, the voltage V_{\text{R}_{\text{b}}} across the base resistor Rb is

V_{\text{R}_{\text{b}}} = V_{\text{cc}} \, - \, \mathord{\overbrace{(I_{\text{c}} + I_{\text{b}}) R_{\text{c}}}^{\text{Voltage drop across } R_{\text{c}}}} \, - \, \mathord{\overbrace{V_{\text{be}}}^{\text{Voltage at base}}}.

By the Ebers–Moll model, Ic = βIb, and so

V_{\text{R}_{\text{b}}} = V_{\text{cc}} - (\overbrace{\beta I_{\text{b}}}^{I_{\text{c}}} + I_{\text{b}}) R_{\text{c}} -  V_{\text{be}} = V_{\text{cc}} - I_{\text{b}} (\beta + 1) R_{\text{c}} -  V_{\text{be}}.

From Ohm's law, the base current I_{\text{b}} = V_{\text{R}_{\text{b}}} / R_{\text{b}}, and so

\overbrace{I_{\text{b}} R_{\text{b}}}^{V_{\text{R}_{\text{b}}}} = V_{\text{cc}} - I_{\text{b}} (\beta + 1) R_{\text{c}} -  V_{\text{be}}.

Hence, the base current Ib is

I_{\text{b}} = \frac{ V_{\text{cc}} - V_{\text{be}} }{ R_{\text{b}} + ( \beta + 1 ) R_{\text{c}} }

If Vbe is held constant and temperature increases, then the collector current Ic increases. However, a larger Ic causes the voltage drop across resistor Rc to increase, which in turn reduces the voltage V_{\text{R}_{\text{b}}} across the base resistor Rb. A lower base-resistor voltage drop reduces the base current Ib, which results in less collector current Ic. Because an increase in collector current with temperature is opposed, the operating point is kept stable.

Merits:

  • Circuit stabilizes the operating point against variations in temperature and β (i.e. replacement of transistor)

Demerits:

  • In this circuit, to keep Ic independent of β, the following condition must be met:
I_{\text{c}} = \beta I_{\text{b}} = \frac { \beta (V_{\text{cc}} - V_{\text{be}})}{R_{\text{b}} + R_{\text{c}} + \beta R_{\text{c}}} \approx \frac{(V_{\text{cc}} - V_{\text{be}})}{R_{\text{c}}}

which is the case when

\beta R_{\text{c}} \gg R_{\text{b}}.
  • As β-value is fixed (and generally unknown) for a given transistor, this relation can be satisfied either by keeping Rc fairly large or making Rb very low.
  • If Rc is large, a high Vcc is necessary, which increases cost as well as precautions necessary while handling.
  • If Rb is low, the reverse bias of the collector–base region is small, which limits the range of collector voltage swing that leaves the transistor in active mode.
  • The resistor Rb causes an AC feedback, reducing the voltage gain of the amplifier. This undesirable effect is a trade-off for greater Q-point stability.

Usage: The feedback also decreases the input impedance of the amplifier as seen from the base, which can be advantageous. Due to the gain reduction from feedback, this biasing form is used only when the trade-off for stability is warranted.

Fixed bias with emitter resistor

Fixed bias with emitter resistor

The fixed bias circuit is modified by attaching an external resistor to the emitter. This resistor introduces negative feedback that stabilizes the Q-point. From Kirchhoff's voltage law, the voltage across the base resistor is

VRb = VCC - IeRe - Vbe.

From Ohm's law, the base current is

Ib = VRb / Rb.

The way feedback controls the bias point is as follows. If Vbe is held constant and temperature increases, emitter current increases. However, a larger Ie increases the emitter voltage Ve = IeRe, which in turn reduces the voltage VRb across the base resistor. A lower base-resistor voltage drop reduces the base current, which results in less collector current because Ic = ß IB. Collector current and emitter current are related by Ic = α Ie with α ≈ 1, so increase in emitter current with temperature is opposed, and operating point is kept stable.

Similarly, if the transistor is replaced by another, there may be a change in IC (corresponding to change in β-value, for example). By similar process as above, the change is negated and operating point kept stable.

For the given circuit,

IB = (VCC - Vbe)/(RB + (β+1)RE).

Merits:

The circuit has the tendency to stabilize operating point against changes in temperature and β-value.

Demerits:

  • In this circuit, to keep IC independent of β the following condition must be met:
I_C = \beta I_B = \frac { \beta (V_{CC} - V_{be})}{R_B+ ( \beta+1) R_E} \approx \frac {(V_{CC} - V_{be})}{R_E}

which is approximately the case if

( β + 1 )RE >> RB.
  • As β-value is fixed for a given transistor, this relation can be satisfied either by keeping RE very large, or making RB very low.
  • If RE is of large value, high VCC is necessary. This increases cost as well as precautions necessary while handling.
  • If RB is low, a separate low voltage supply should be used in the base circuit. Using two supplies of different voltages is impractical.
  • In addition to the above, RE causes ac feedback which reduces the voltage gain of the amplifier.

Usage:

The feedback also increases the input impedance of the amplifier when seen from the base, which can be advantageous. Due to the above disadvantages, this type of biasing circuit is used only with careful consideration of the trade-offs involved.

Collector-Stabilized Biasing

Voltage divider biasing

Voltage divider bias

The voltage divider is formed using external resistors R1 and R2. The voltage across R2 forward biases the emitter junction. By proper selection of resistors R1 and R2, the operating point of the transistor can be made independent of β. In this circuit, the voltage divider holds the base voltage fixed independent of base current provided the divider current is large compared to the base current. However, even with a fixed base voltage, collector current varies with temperature (for example) so an emitter resistor is added to stabilize the Q-point, similar to the above circuits with emitter resistor.

In this circuit the base voltage is given by:

V_B = \ voltage across R_2 \ = V_{cc} \frac{R_2}{(R_1+R_2)} - I_B \frac{R_1 R_2}{(R_1+R_2)}

\approx V_{cc} \frac{R_2}{(R_1+R_2)} provided I_B << I_2 = V_B / R_2 \ .

Also V_B = V_{be} + I_ER_E \

For the given circuit,

 I_B =\frac 
{
 \frac 
{V_{CC}}{1+R_1/R_2}
 - V_{be}
}
{( \beta + 1)R_E + R_1 \parallel R_2 } .

Merits:

  • Unlike above circuits, only one dc supply is necessary.
  • Operating point is almost independent of β variation.
  • Operating point stabilized against shift in temperature.

Demerits:

  • In this circuit, to keep IC independent of β the following condition must be met:
I_C = \beta I_B = \beta \frac 
{ 
 \frac 
{V_{CC}}{1+R_1/R_2}
 - V_{be}
}
{( \beta + 1)R_E + R_1 \parallel R_2 } \approx \frac 
{ \frac {V_{CC}}{1+R_1/R_2}- V_{be}}
{R_E} ,

which is approximately the case if

( \beta + 1 ) R_E >> R_1 \parallel R_2

where R1 || R2 denotes the equivalent resistance of R1 and R2 connected in parallel.

  • As β-value is fixed for a given transistor, this relation can be satisfied either by keeping RE fairly large, or making R1||R2 very low.
  • If RE is of large value, high VCC is necessary. This increases cost as well as precautions necessary while handling.
  • If R1 || R2 is low, either R1 is low, or R2 is low, or both are low. A low R1 raises VB closer to VC, reducing the available swing in collector voltage, and limiting how large RC can be made without driving the transistor out of active mode. A low R2 lowers Vbe, reducing the allowed collector current. Lowering both resistor values draws more current from the power supply and lowers the input resistance of the amplifier as seen from the base.
  • AC as well as DC feedback is caused by RE, which reduces the AC voltage gain of the amplifier. A method to avoid AC feedback while retaining DC feedback is discussed below.

Usage:

The circuit's stability and merits as above make it widely used for linear circuits.

Voltage divider with AC bypass capacitor

Voltage divider with capacitor

The standard voltage divider circuit discussed above faces a drawback - AC feedback caused by resistor RE reduces the gain. This can be avoided by placing a capacitor (CE) in parallel with RE, as shown in circuit diagram.

This capacitor is usually chosen to have a low enough reactance at the signal frequencies of interest such that RE is essentially shorted at AC, thus grounding the emitter. Feedback is therefore only present at DC to stabilize the operating point, in which case any AC advantages of feedback are lost.

Of course, this idea can be used to shunt only a portion of RE, thereby retaining some AC feedback.

Emitter bias

Emitter bias

When a split supply (dual power supply) is available, this biasing circuit is the most effective, and provides zero bias voltage at the emitter or collector for load. The negative supply VEE is used to forward-bias the emitter junction through RE. The positive supply VCC is used to reverse-bias the collector junction. Only two resistors are necessary for the common collector stage and four resistors for the common emitter or common base stage.

We know that,

VB - VE = Vbe

If RB is small enough, base voltage will be approximately zero. Therefore emitter current is,

IE = (VEE - Vbe)/RE

The operating point is independent of β if RE >> RB

Merit:

Good stability of operating point similar to voltage divider bias.

Demerit:

This type can only be used when a split (dual) power supply is available.

Class B and AB amplifiers

Signal requirements

Class B and AB amplifiers employ 2 active devices to cover the complete 360 deg of input signal flow. Each transistor is therefore biased to perform over approximately 180 deg of the input signal. Class B bias is when the collector current Ic with no signal is just conducting (about 1 % of maximum possible value). Class AB bias is when the collector current Ic is about 1/4 of maximum possible value. The class AB push–pull output amplifier circuit below could be the basis for a moderate-power audio amplifier.

A practical amplifier circuit
A practical amplifier circuit

Q3 is a common emitter stage that provides amplification of the signal and the DC bias current through D1 and D2 to generate a bias voltage for the output devices. The output pair are arranged in Class AB push–pull, also called a complementary pair. The diodes D1 and D2 provide a small amount of constant voltage bias for the output pair, just biasing them into the conducting state so that crossover distortion is minimized. That is, the diodes push the output stage into class-AB mode (assuming that the base-emitter drop of the output transistors is reduced by heat dissipation).

This design automatically stabilizes its operating point, since overall feedback internally operates from DC up through the audio range and beyond. The use of fixed diode bias requires the diodes to be both electrically and thermally matched to the output transistors. If the output transistors conduct too much, they can easily overheat and destroy themselves, as the full current from the power supply is not limited at this stage.

A common solution to help stabilize the output device operating point is to include some emitter resistors, typically an ohm or so. Calculating the values of the circuit's resistors and capacitors is done based on the components employed and the intended use of the amplifier.

References

  1. ^ A.S. Sedra and K.C. Smith (2004). Microelectronic Circuits (5th ed.). New York: Oxford University Press. p. 397, Figure 5.17, and p. 1245. ISBN 0-19-514251-9. 

Further reading

  • Patil, P.K.; Chitnis, M.M. (2005). Basic Electricity and Semiconductor Devices. Phadke Prakashan. 

See also

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Biasing (electronics) — Biasing in electronics is the method of establishing predetermined voltages and/or currents at various points of a circuit to set an appropriate operating point .The operating point of a device, also known as bias point or quiescent point (or… …   Wikipedia

  • Heterojunction bipolar transistor — The heterojunction bipolar transistor (HBT) is a type of bipolar junction transistor (BJT) which uses differing semiconductor materials for the emitter and base regions, creating a heterojunction. The HBT improves on the BJT in that it that can… …   Wikipedia

  • Bipolar junction transistor — BJT redirects here. For the Japanese language proficiency test, see Business Japanese Proficiency Test. PNP …   Wikipedia

  • Biasing — This article is about biasing in electronics. For other uses, see Biasing (disambiguation). Biasing in electronics is the method of establishing predetermined voltages and/or currents at various points of an electronic circuit to set an… …   Wikipedia

  • Resistor–transistor logic — (RTL) is a class of digital circuits built using resistors as the input network and bipolar junction transistors (BJTs) as switching devices. RTL is the earliest class of transistorized digital logic circuit used; other classes include… …   Wikipedia

  • Grown-junction transistor — The grown junction transistor was the first type of bipolar junction transistor made [ [http://semiconductormuseum.com/PhotoGallery/PhotoGallery M1752.htm TRANSISTOR MUSEUM Historic Transistor Photo Gallery BELL LABS TYPE M1752] ] . It was… …   Wikipedia

  • semiconductor device — ▪ electronics Introduction       electronic circuit component made from a material that is neither a good conductor nor a good insulator (hence semiconductor). Such devices have found wide applications because of their compactness, reliability,… …   Universalium

  • Common collector — Figure 1: Basic NPN common collector circuit (neglecting biasing details). In electronics, a common collector amplifier (also known as an emitter follower or BJT voltage follower) is one of three basic single stage bipolar junction transistor… …   Wikipedia

  • Cascode — The cascode is a two stage amplifier composed of a transconductance amplifier followed by a current buffer. Compared to a single amplifier stage, this combination may have one or more of the following advantages: higher input output isolation,… …   Wikipedia

  • Thermal runaway — refers to a situation where an increase in temperature changes the conditions in a way that causes a further increase in temperature leading to a destructive result. It is a kind of positive feedback.Chemical engineeringIn chemical engineering,… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”