Motorcycle fairing

Motorcycle fairing
1956 NSU world record setting Dolphin II
NSU Sportmax 1955, dustbin fairing
BMW K1200GT touring motorcycle with full fairing

A motorcycle fairing is a shell placed over the frame of some motorcycles, especially racing motorcycles and sport bikes, with the primary purpose to reduce air drag. The secondary functions are the protection of the rider from airborne hazards and wind-induced hypothermia and of the engine components in the case of an accident. There may be a front fairing, as well as a rear fairing component. A motorcycle windshield may be an integral part of the fairing.[1]

The major benefit of a fairing on sport touring and touring motorcycles is a reduction in fuel consumption.[2] The reduction in aerodynamic drag allows for taller gearing, which in turn increases engine life.

Contents

History

The importance of streamlining was known very early in the 20th century. Some streamlining was seen on racing motorcycles as early as the 1920s. The effects of aerodynamic drag on motorcycles are very significant.

The term fairing came into use in aircraft aerodynamics with regard to smoothing airflow over a juncture of components where airflow was disrupted. Early streamlining was often unsuccessful resulting in instability. Handlebar fairings, such as those on Harley-Davidson Tourers, sometimes upset the balance of a motorcycle, inducing wobble.[3] The first factory installed full fairing was that installed on the BMW R100RS introduced in 1976.[4] This marked the beginning of widespread adoption of fairings on sports, and touring types of motorcycles.

Originally the fairings were cowlings put around the front of the bike, increasing its frontal area. Gradually they had become an integral part of the design. Modern fairings increase the frontal area at most by 5% compared to a naked machine. Fairing may carry headlights, instruments, and other items. If the fairing is mounted on the frame, mounting equipment on the fairing reduces the weight and rotational inertia of the steering assembly, improving the handling.[5]

Types

  • Streamliner: This is a full fairing as found on land speed record machines. The entire body of the motorcycle is covered to provide the lowest drag coefficient ratio attainable. The NSU Dolphin II (Delphin II) is a streamliner.[6]
  • Dustbin fairing: A single-piece, streamlined shell covering the front half of a motorcycle resembling the nose of an aircraft, sometimes referred to as torpedo fairing. It dramatically reduced the frontal drag, but it was banned by Fédération Internationale de Motocyclisme (FIM) from racing in 1958, because it was thought that the frontal point of wind pressure made them highly unstable even with small amounts of yaw.[5] Other reasons cited for the ban were to ensure adequate steering range (lock-to-lock) and stability against crosswinds. FIM regulations forbid streamlining beyond the wheel spindles and require the rider's arms and legs to be visible from the side.[5]
  • Dolphin fairing: It was called so because in early models the front wheel mud guard streamlined with the rising windshield part of the fairing resembled the dolphin's beak from the side view. They had become the norm since the ban of the dustbins.[5]
Harley-Davidson police motorcycle with "batwing" fairing
  • Full-fairing: Bodywork that covers both upper and lower portions of the motorcycle, as distinct from a half fairing, which only has an upper section, and the lower half of the motorcycle is exposed. The fairing on a race or sport bike is meant as an aerodynamic aid, so the windscreen is rarely looked through. If the rider is sitting up at speed he will be buffeted by his rapid progress through the air and act as a parachute, slowing the bike, while if the rider lies flat on the tank behind the windscreen he generates much less aerodynamic drag. The high windscreen and handle-bar width of a touring fairing protect the upright rider from the worst of this, and the windscreen is functional. Full fairings can also provide protection to the engine and chassis in the event of a crash where the fairings, rather than the engine covers and/or frame, slide on the road.
Suzuki SV650s with half fairing and an aftermarket belly pan.
  • Half-fairing: Fairing that features a windscreen and fairing extending at least below the handlebars, even as far as down to the sides of the cylinder block, though generally half-fairing doesn't cover the sides of the crankcase or gear box. A number of half-faired models have aftermarket kits available to extend the original half-fairing into a full fairing. Due to the popularity of these kits some manufacturers have started to supply their own full-fairing conversion kits and even offer their half-faired models new with a full-fairing kit fitted at the factory.
  • Quarter fairing: A windscreen and minimal fairing extending around the headlight fixed to the triple clamp; also referred to as a "bikini fairing".
  • Belly pan: Quarter and half fairings are often paired with a belly pan below the engine for diverting air flow away from under the engine to reduce aerodynamic lift, as well as cosmetic reasons. Some track day or racing rules require belly pans to catch leaked fluids.[7]

Materials

Acrylonitrile butadiene styrene (ABS) plastic is commonly used in original equipment sport bikes and certain aftermarket fairing manufacturers due to its strong, flexible and light weight properties. The advantage of ABS over other plastics is that it combines the strength and rigidity of acrylonitrile and styrene with the toughness of polybutadiene rubber. The proportions of each property vary based on the targeted result.

There are two common methods of producing ABS plastic fairing: injection and compression.

  • Injection molds: ABS plastic is melted and injected into mold cavity. Constant pressure is applied to allow for material shrinkage. The plastic then cools and hardens in the mold. Injection molds allows for uniform thickness throughout the entire piece. It gives the most accurate end product that fits well.
  • Compression molds: The plastic is generally preheated is placed into a heated metal mold cavity and pressure is applied to force the plastic to contract and take the shape of the mold. Heat and pressure is kept until the plastic cures the mold. The excess plastic is cut away and removed from the mold. Disadvantages to compression mold include varying product consistency and flashing, which is excess material attached to the molded part that needs to be removed where two or more parts of the mold meet.

Fiberglass is made of woven fibers, and is used as a reinforcing agent for many polymer products. The composite properly known as glass-reinforced plastic (GRP), is normally referred to by the name of its reinforcing material. Fiberglass fairings are commonly used on the race track. In most cases fiberglass is lighter, and more durable than ABS Plastic. Damaged fiberglass can be repaired by applying new layers of woven fiberglass cloth mixed with a polymer such as epoxy, over the damaged area followed sanding and finishing.

Carbon-fiber-reinforced polymer is the lightest, but most expensive, fairing material. It is used on the most extreme sport and racing motorcycle fairings.[8]

See also

Notes

  1. ^ Tony Foale, Motorcycle Handling and Chassis Design, ISBN 84-933286-3-4 , Chapter 5: "Aerodynamics"
  2. ^ Fuel Economy Begins with Streamlining
  3. ^ 2009 Harley-Davidson Electra Glide Standard Review
  4. ^ Sport-Touring Defined: The BMW RS Series
  5. ^ a b c d John Robinson, "Motorcycle Tuning: Chassis", ISBN 0-7506-1840-X, p.132
  6. ^ NSU Breaks 200 MPH Barrier
  7. ^ Larson, Kent (2005), Motorcycle Track Day Handbook, MotorBooks/MBI Publishing Company, p. 115, ISBN 9780760317617, http://books.google.com/books?id=gg1LM967OhMC&pg=PA115, retrieved 2011-03-05 
  8. ^ Cameron, Kevin (1998), Sportbike Performance Handbook, St. Paul MN: Motorbooks, p. 8, ISBN 978-0-7603-0229-3, http://books.google.com/books?id=J7tQp2LtsYIC&pg=PA8 

References

  • P. E. Freathy, J. D. Potter (1979) "An Investigation of the Performance of the Motorcycle Fairing", University of Bristol, Dept. of Aeronautical Engineering

Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Motorcycle accessories — are features and accessories selected by a motorcycle owner to enhance safety, performance, or comfort, and may include anything from mobile electronics to sidecars and trailers. An accessory may be added at the factory by the original equipment… …   Wikipedia

  • Fairing — may refer to:Aerodynamic/Hydrodynamic*Aircraft fairing, a structure in aircraft design used to reduce drag and improve appearance *Bicycle fairing, a type of fairing coverage for bicycles *Motorcycle fairing, a type of fairing applied to… …   Wikipedia

  • Motorcycle windshield — Motorcycle windshields or windscreens are clear glass or plastic structures mounted in front of the motorcycle with the primary goal to guard the rider from wind, as well as from airborne hazard, such as rain. A windshield may be either mounted… …   Wikipedia

  • Motorcycle components — and systems for a motorcycle are engineered, manufactured, and assembled in order to produce motorcycle models with the desired performance, aesthetics, and cost. The key components of modern motorcycles are presented below. Contents 1 Chassis… …   Wikipedia

  • Motorcycle stunt riding — Motorcycle stunt riding, sometimes referred to as simply stuntriding, is a motorcycle sport characterized by stunts involving acrobatic maneuvering of the motorcycle and sometimes the rider. Common maneuvers in stunt riding include wheelies,… …   Wikipedia

  • Motorcycle history — The 1900 Werner Brothers patented motorcycle Motorcycle history begins in the second half of the 19th century. Motorcycles are descended from the safety bicycle, a bicycle with front and rear wheels of the same size and a pedal crank mechanism to …   Wikipedia

  • Motorcycle engine — A Honda Super Cub engine. The most popular motorcycle in history, with over 60 million produced …   Wikipedia

  • Motorcycle — For other uses, see Motorcycle (disambiguation). A 1954 Triumph T110 650 cc motorcycle …   Wikipedia

  • Motorcycle training — Army National Guard motorcycle riders hone their skills during the Army Guard hosted Motorcycle Safety Foundation Sport bike Rider Certification Course. January 30, 2009 at Fort Rucker, Alabama. Motorcycle training teaches motorcycle riders the… …   Wikipedia

  • Motorcycle fork — 1968 BMW R60US with conventional telescopic fork Unusual trailing bottom …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”