Pterodactyl Ascender

This article is about the ultralight aircraft. For the Chinese unmanned aerial vehicle, see Chengdu Pterodactyl I.

Pterodactyl series
Pterodactyl Ascender II+2
Role	ultralight personal, trainer aircraft
National origin	USA
Manufacturer	Pterodactyl Limited
Designer	Jack McCornack
First flight	1977
Introduction	1979
Produced	1979–1984
Number built	1396
Unit cost	USD$2750 (Pfledge OR 1978)
Developed from	Manta Fledge IIB hang glider

Jack McCornack flying the Pterodactyl Ascender II in a zoom

An Ascender II+2 two seater. The powerplant is a Rotax 503 50 hp (37 kW) two stroke.

Pterodactyl Ascender II+2

Fly camping with a DFE Ascender III-C two seater.

Newly completed DFE Ascender III-C prior to first flight, 2004

DFE Ascender III-C in front of its hangar. The aircraft in the background is a Quad City Challenger II.

The Pterodactyl Ascender is a family of U.S. designed and built ultralight aircraft that were sold in kit form between 1979 and 1984 under Pterodactyl Limited and is currently being sold by DFE Ultralights.

With a total production of 1,396 aircraft between 1979 and 1984 plus limited production today as the DFE Ascender III series, the aircraft has been one of the most influential designs in ultralight aviation.^[1][2]

Development

The Pterodactyl designs have their roots in the Manta Fledge hang gliders of the 1970s. The Fledge was designed by Klaus Hill and produced by Manta Products in a series that ran from the Fledge I to the IV, with numerous sub models designated by letters. The Fledge series were of a "rigid-wing" type, as opposed to the predominantly “flex-wing” hang glider designs then common. These designs all featured weight-shift pitch control and tip-rudders for yaw and roll control. The tip rudders were controlled by control-bar sliders which deployed one tip rudder at a time to create a yaw. The glider's swept wing then translated the yaw into a matched rolling motion. The Fledge series were considered to be high performance hang gliders during their production run in the 1970s.^[1][2]

California inventor Jack McCornack took the Fledge IIB wing and designed a tubular assembly that replaced the Fledge's hang glider seat with a reclined pilot seat, wheeled landing gear and engine mount for a pusher powerplant. The aircraft used a mouth-controlled throttle, as both hands were used on the tip rudder twist grips which were retained from the Fledge. The aircraft had no canard or tail and was a true flying wing. Power was supplied by a two-stroke Xenoah engine of 16 horsepower driving a 36-inch propeller. This new design, named the Pterodactyl Fledgling, was first flown in 1977. It is also referred to variously as the Pterodactyl Fledge and Pfledge^[1][2]

The aircraft was first publicly displayed at an ultralight fly-in at Gilroy, California in 1978. McCornack formed Pterodactyl Limited to produce an improved version of the design, designated the Fledge X powered by the Xenoah 242 16 hp (12 kW) engine.^[1]

In 1979 McCornack and his flying partner, Keith Nicely, flew two improved Fledglings from their base in Monterey, California to Oshkosh, Wisconsin, where they made a positive impression on the large gathering of pilots at the EAA annual convention there. At the convention they were invited by Mother Earth News magazine to fly the aircraft on to the Atlantic coast on pure ethanol supplied by the magazine. The flight from coast to coast was one of the longest trips of the period and garnered much attention for the start-up company.^[1][3]

Limited production of the version flown to Oshkosh started in the fall of 1979. The model was called the Pterodactyl Pfledge OR (Oshkosh Replica) and was powered by a Sachs SA-340 336 cc direct drive two-stroke engine.^[4]

Construction of all Pterodactyl aircraft was of similar material, predominantly anodized 6061-T6 aluminum tubing, braced with swaged steel cables supported by a king post, with a sewn Dacron sail for wing covering. Fittings to join the tubing was either extruded or made from sheet, connected with aircraft AN bolts. The sails came in a wide variety of colour combinations.^[5][2]

The company was moved in 1980 from Monterey to a new 7,200-square-foot (670 m²) facility co-located with the Seventh-day Adventist Monterey Bay Academy at Watsonville, California and series production of the Pfledge was commenced. The new location was ideal as it included access to the Monterey Bay Academy Airport. The design went through a series of evolutionary improvements, mostly involving the powerplants installed and these resulted in a number of different models.^[6]

Variants

Pfledge

The first Pfledges (also referred to as Fledges, and Fledglings) were tailless flying wings powered by a two-stroke Xenoah engine driving a 36-inch propeller. Some were also powered by a 10 hp (7 kW) 136 cc Chrysler two stroke engine.^[5][2]

Pfledge X

The Pfledge X featured a Xenoah 242 powerplant that produced 16 hp (12 kW).^[1]

Pfledge OR

The "Oshkosh Replica" was the production version of the two aircraft that were flown coast to coast in 1979. It was powered by a German Sachs SA-340 direct drive engine with a 336 cc displacement. This model sold for USD$3500 in 1980.^[6]

Pfledge 430D

The Pfledge 430D was announced late in 1979. This model featured a Cuyuna 430D engine which McCornack helped design. The engine was a two cylinder, two stroke engine with a displacement of 429 cc and a power output of 30 hp (22 kW). It weighed 64 lb (29 kg). The "D" indicated that the engine was direct drive and not connected to the propeller through a reduction drive system.^[6][2]

The Pfledge 430D also replaced the twist grips with a conventional stick for roll control, while pitch remained via weight shift.^[6]

The Pfledge 430D cost USD$3600 in 1980.^[6]

NFL

Before the introduction of its FAR 103 ultralight regulations in 1982 the FAA did not regulate ultralights as long as they were foot-launchable.^[1][7]

The demand from conventional aircraft pilots for a version of the Pfledge that had aerodynamic pitch control instead of weight-shift led McCornack to add an elevator to the back of the aircraft, mounted on twin booms behind the pusher propeller. Because this design was "Not Foot Launchable" it was called the NFL (pronounced "Niffle"). The design was not a production success and few were built, but the NFL paved the way for the Ptraveler and Ascender to follow.^[1][7]

Ptraveler

McCornack had first installed a canard elevator on a Pfledge in 1978, but did not create a production model until 1980. The canard was operated by a side-mounted control stick. Fore-and-aft movement of the stick moved the canard and sideways movement controlled the tip-rudders. The canard was constructed with tubular spars, aluminum ribs and covered in Mylar, although some were also covered using standard aircraft fabric.^[7]

The new model carried the name "Ptraveler", continuing the use of the silent letter “P” in Pterodactyl designs.^[7]

The new model was powered by the Cuyuna 430D direct drive engine and was introduced in 1980 at a price of USD$3900.^[7]

Ascender

The Cuyuna 430D powerplant was greatly improved by the addition of a 2:1 belt reduction drive, allowing larger propellers of 54 inches diameter to be used. This produced more thrust and less noise. The modified powerplant was called the Cuyuna 430R.^[8][2]

Fitting the new powerplant into the Ptraveler drastically improved the aircraft's take-off and climb performance. The new model was named the “Ascender” for its improved climb rate and also in tribute to the XP-55 Ascender, an early canard fighter design. In 1981 a complete kit cost USD$4200.^[1][2]

Ascender II

The Ascender II was an improved Ascender with evolutionary changes incorporated. It had an improved muffler, re-located throttle and fiberglass spring rod main landing gear suspension.^[1]

Psounder

The Pterodactyl Psounder was a one-of-a kind Ascender II that was modified for an atmospheric research project at Colorado State University.^[9]

Ptug

The Ptug was a special hang glider towing version of the Ascender II that was modified with a special rigid bridle to ensure that the tow rope stayed clear of the propeller.^[1]

Ptiger

By adding a fiberglass fairing to the basic Ascender II airframe, along with clipping the wing by 4 feet (1 m) to a 29-foot (9 m) span, the result was a new model named the "Ptiger". With the Cuyuna 430R the aircraft was capable of 75 mph (121 km/h) in level flight.^[10]

Under the rules of the time it could not be foot-launched and Pterodactyl advised purchasers to register their Ptigers as experimental amateur-built aircraft^[10]

Ascender II+

The Ascender II+ was introduced in early 1982 and was aimed at the physically larger pilot. This redesigned model incorporated a wider 20 ½ inch hang cage. All earlier models had a 15+³⁄₄-inch-wide (400 mm) hang cage. It also had stronger upright struts and wing with 1 ¾” inch spars of 0.049” thickness, whereas all earlier models used 1 ½” spars of 0.049 inch thickness and heavier 1/8” outer bottom cables.^[1]

The Ascender II+ sold for USD$5260 in 1983.^[1]

Ascender II+2

The Ascender II+, with its additional structural strength lent itself to the creation of a two-seat trainer version. This was designed by adding an off-center "sidecar" frame to hold the second seat and was named the "Ascender II+2". There was no dual control installation, as both pilots had access to the single side-stick control.^[9]

The II+2 was first marketed in the middle of 1982 at a price of USD$5560.^[1]

Light Flyer

The final aircraft design and produced by Pterodactyl was based on the Easy Riser wing and was a tribute to the Wright Flyer. The Light Flyer introduced practical improvements over the original Wright brothers design, such as wheeled landing gear instead of fixed skids, allowing taxiing. The aircraft was introduced in 1984 at a price of USD$5400, but only about five were sold.^[1]

Production

Pterodactyl production commenced in 1979 and was completed in 1984, when the company was sold to a group of partners under the name "Freedom Fliers" and moved to Rowlett, Texas. The company quickly went out of business, and few aircraft were completed. McCornack was never paid for the sale of the company. A total of 1,396 aircraft were built by Pterodactyl.^[1]

DFE Ultralights

In 1991 one of McCornack's original dealers from 1978, Dave Froble, started producing parts to keep his own fleet of Pterodactyls flying. He located and purchased the old stock of Manta Products airframe parts and produced CAD drawings for the complete parts.^[1][2]

In 1992 Froble started making kits available for complete aircraft in three models under the company name DFE Ultralights (Dave Froble Enterprises). These were very similar to the original Pfledge and Ascender series and were named Ascender III, with letters to designate the various models.^[1]

DFE Ultralights has produced a small number of complete kits and continues to support the fleet of existing aircraft with parts to keep them flying.^[1]

Ascender III-A

The Ascender III-A is similar to the original Pterodactyl Pfledge. It lacks a canard and pitch control is by weight shift, although it incorporates some refinements, such as nose wheel steering. The 2003 price was USD$6800.^[1][2]

Ascender III-B

The Ascender III-B is similar to the Pterodactyl Ascender II with the addition of nose wheel steering and in 2003 sold for USD$7900.^[1][2]

Ascender III-C

The Ascender III-C is equivalent to the Pterodactyl Ascender II+ with the heavy-duty style airframe. It sold for USD$8100 in 2003.^[1]

Like the Ascender II+, the Ascender III-C can be fitted with a sidecar to become a two-seat trainer version.^[1]

Ascender III-T

The Ascender III-T is similar to the Pterodactyl Ascender II Ptug hang glider tug aircraft and incorporates a bridle to fit around the propeller to attach the tow rope to.^[1][2]

Regulatory status

In the USA the single seat Pterodactyl models are flown as ultralights under FAR 103^[11], whereas the two seat models are usually registered as experimental amateur-builts.

In Canada all Pterodactyls are classified as Basic Ultra-lights.^[12]

Notable flights

Pterodactyls have been flown on many long flights. John D. (Jack) Peterson, Jr. completed a flight in a Pfledge from Long Beach, California to Hilton Head, South Carolina over a period of 29 days between July 9 and August 6, 1979, with ground support. He flew the 3,200-mile (5,100 km) distance by flying distances of a maximum of 120 miles (194 km) in a single flight. This feat was the first time that an ultralight airplane had been flown across the USA from coast to coast. Peterson’s aircraft is on display in the Smithsonian Museum's Steven F. Udvar-Hazy Center.^[1]

McCornack and Nicely's 1979 flight from Monterey, California to Oshkosh, Wisconsin and onto the Atlantic coast was the second transcontinental flight by this aircraft type and was done mostly without ground support.^[1]

Present day

In the 21st century many Pterodactyls are still in use by private owners. As when first introduced, they remain prized for their simplicity, rugged off-field capabilities and amazing climb performance.^[1]

Specifications (1979 model Pterodactyl Pfledge)

General characteristics

• Crew: one pilot
• Length: 11 ft 6 in (3.5 m)
• Wingspan: 33 ft 0 in (10.15 m)
• Height: 10 ft 6 in (3.2 m)
• Wing area: 162 sq ft (15.3 m²)
• Empty weight: 125 lb (56.7 kg)
• Useful load: 225 lb (102 kg)
• Max takeoff weight: 350 lb (159 kg)
• Powerplant: 1 × Xenoah 242 two stroke, 16 hp (12 kW)

Performance

• Never exceed speed: 50mph (80 km/h)
• Maximum speed: 50 mph (80 km/h)
• Cruise speed: 45 mph (73 km/h)
• Stall speed: 17 mph (28 km/h)
• Range: 56 miles (91 km)
• Rate of climb: 300 ft/min (92 m/min)
• Wing loading: 2.16 lb/sq ft (10.4 kg/sq m)
• Power/mass: 21.9 lb/hp (0.075 kW/kg)

See also

Aircraft of comparable role, configuration and era

• AmEagle American Eaglet
• AmeriPlanes Mitchell Wing A-10
• Chotia Weedhopper
• Eipper Quicksilver
• International Ultralite Banchee
• Moyes Dragonfly - also used for towing hang gliders
• UFM Easy Riser
• Ultraflight Lazair
• Wings of Freedom Flitplane
• Zenair Zipper
  

References

1. ^ ^{a b c d e f g h i j k l m n o p q r s t u v w x y z aa} Hunt, Adam (2 September 2005). "Pterodactyl History". http://pterodactyl.squarespace.com/pterodactyl-history/. Retrieved 2009-08-25. 
2. ^ ^{a b c d e f g h i j k l} Cliche, Andre: Ultralight Aircraft Shopper's Guide 8th Edition, pages B-4-5. Cybair Limited Publishing, 2001. ISBN 0-9680628-1-4
3. ^ Jack McCornack (November/December 1979). "Mother Earth News, The Flight of the Microlights". http://www.motherearthnews.com/DIY/1979-11-01/The-Flight-of-the-Microlights.aspx. Retrieved 2007-11-06. 
4. ^ McCornack, Jack: Ptimes, Volume 1 Number 3. Pterodactyl Limited, Winter 1979.
5. ^ ^{a b} McCornack, Jack: Ptimes, Volume 1 Number 1. Pterodactyl Limited, Summer 1979.
6. ^ ^{a b c d e} McCornack, Jack: Ptimes, Volume 1 Number 4. Pterodactyl Limited, Winter 1979.
7. ^ ^{a b c d e} McCornack, Jack: Ptimes, Volume 2 Number 1. Pterodactyl Limited, Spring 1980.
8. ^ McCornack, Jack: Ptimes, Volume 2 Number 2. Pterodactyl Limited, Late Spring 1981.
9. ^ ^{a b} McCornack, Jack: Ptimes Volume 3. Pterodactyl Limited, Late 1982.
10. ^ ^{a b} McCornack, Jack: Ptimes Volume 2, Number 3 & 4. Pterodactyl Limited, June 1982.
11. ^ Federal Aviation Administration (December 17, 1991). "Electronic Code of Fedrral Regulations Title 14: Aeronautics and Space, Part 103 - Ultralight Vehicles". http://ecfr.gpoaccess.gov/cgi/t/text/text-idx?c=ecfr&sid=a73fb5f5f481ec944d3f945a7fc1a031&rgn=div5&view=text&node=14:2.0.1.3.16&idno=14/menu.htm. Retrieved 2007-11-07. 
12. ^ Transport Canada (April 17, 2007). "Ultra-light Aeroplane Transition Strategy". http://www.tc.gc.ca/civilaviation/general/recavi/Ultralight/ULTransitionStrategy/menu.htm. Retrieved 2007-11-04. 

External links