Rigid Panels

Rigid Panels

Rigid panel insulation is made from fibrous materials (fiberglass, rock and slag wool) or from plastic foam. They are sometimes sold in sections designed to fit tightly in standard wall cavities. When sold this way, they are called "batts", and they come in different thicknesses to match the depth of wall cavities, for example, approx. 5½ inches to match a 2 x 6 inch wall cavity.

Where rigid panels are most often used:
* Some, such as EPS "beadboard", are suitable for ground contact and are used against footings and exterior backfilled foundation walls.
* Against exterior exposed foundation walls (should be coated to protect from sunlight).
* Against exterior walls between foundation and roof, installed between sheathing and siding.
* Either under or on top of the roof sheathing.
* Inside unfinished interior walls, either as pre-cut batts, or as panels cut to fit inside walls and secured in place.
* Where space is limited and you need to pack great insulating capacity into a small space.

Important note #1: If you insulate the foundation with rigid panels, but you stop using rigid panels where the siding begins, then you should install flashing in between the bottom course of siding and the top edge of the rigid panels, to prevent water from seeping behind the panels.

Important note #2: When insulating the exterior foundation, you should install the rigid panels in two staggered layers, and fill the gaps at the seams with spray foam, to keep moisture from penetrating from the outside. However, when insulating between the sheathing and siding, you should leave slight gaps between the rigid panels to allow moisture to escape from the exterior side of the sheathing.

Advantages

* High R-value per inch - useful where space is tight or cramped, such as cathedral ceiling.
* Protect foundation and damp-proofing during backfilling (and, of course, insulate foundation).
* All are lightweight and strong - although EPS can be crumbly.
* Add to structural strength of walls.
* Provide acoustical insulation as well as thermal.
* Most are easily cut with utility knives.
* All are water resistant, some more so than others (but none should face prolonged exposure to water).
* Will not rot.
* XPS type is highly resistant to air infiltration. Can be virtually airtight if installed without gaps between adjacent panels, with seams taped.
* Reduce heat conduction through the wall frame when used as sheathing.
* Rigid panels with a radiant heat barrier facing foil will significantly improve the insulating properties by reflecting infrared solar energy before penetrating the wall or ceiling.
* Some types use some recycled content.

Disadvantages

* All are susceptible to UV damage and solvents. Building codes require exterior cladding (e.g. stucco) where they are above ground and exposed.
* All are flammable and produce toxic fumes when they burn. All of them should be covered with fire-rated drywall (gypsum board) when installed in the interior of a house, unless they have a low flame-spread rating (below 25).
* More expensive than most other types of insulation.
* Some types may be susceptible to termites using them for nesting purposes.
* May have R-values higher than that of still air, if some type of insulating gas was blown into them during manufacturing. For many years, manufacturers used CFCs or urea formaldehyde as blowing agents. These blowing agents eventually leak out of the panels. CFCs deplete the ozone layer, and formaldehyde is toxic. Some manufacturers still use HCFCs, which are still harmful to the ozone layer, but not to the same extent as CFCs. Eventually, as the blowing agent leaks, air replaces the insulating gas, and the R-value of the panel drops.
* Most rigid panels are made from crude oil byproducts, and some toxic pollution results during their manufacturing.

Types

* Fibreglass and rock wool. These are mainly used for acoustic applications. A company called Roxul in Ontario, Canada uses rock wool as the basis for all of their products, including panels for insulating the exterior foundation. All of their products are naturally fire-resistant. [http://www.roxul.com]
* Perlite - used in Europe
* Phenolic, also known as phenol-formaldehyde. Advantages: High strength. Less flammable than most other foams. Disadvantages: Material is mostly open-celled. This results in insulating capacity not as good as other foams, high water absorption, and high water vapor permeability. Degrades and releases some formaldehyde over time, but not nearly as much as urea formaldehyde.
* Polyurethane. White or yellow. Produced through mixing of isocyanate and polyether in presence of catalyst and blowing agent. Contains many tiny, closed cells. Relatively waterproof, and low water absorption, but must protect from prolonged exposure to water. Can use underground if conditions are relatively dry.
* Rigid cellular polystyrene (RCPS). This includes EPS, MEPS, XPS, beadboard, blueboard, and Styrofoam.
* Polyisocyanurate "(also known as polyiso)". More stable at high temperatures and less flammable than polyurethane. Higher R-value vs. polystyrene and polyurethane due to its gas-filled closed-cell foam structure. Denser and more rigid than polystyrene panels, but more expensive. Must protect from prolonged exposure to water. Usually contains some recycled plastic, such as from PET beverage containers.
* Structural insulating panels (SIP's), also called stressed-skin walls.
* Vacuum insulation consisting of thin panels with extreme insulation capacities, as high as R-50 per inch. However, like double-glazed windows, these eventually lose their air-tight seal.
* Natural fibre insulations (around 0.04 W/mK) all can be treated with low toxicity fire and insect retardents, often used in Europe
* Lightweight Wood Fibre board.
* Cork


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Solar panels on spacecraft — Spacecraft operating in the inner solar system usually rely on the use of photovoltaic solar panels to derive electricity from sunlight. In the outer solar system, where the sunlight is too weak to produce sufficient power, radioisotope thermal… …   Wikipedia

  • Building insulation materials — A selection of insulation materials can aid in building insulation. All of these are based on standard principles of thermal insulation. Materials used to reduce heat transfer by conduction, radiation or convection are employed in varying… …   Wikipedia

  • building construction — Techniques and industry involved in the assembly and erection of structures. Early humans built primarily for shelter, using simple methods. Building materials came from the land, and fabrication was dictated by the limits of the materials and… …   Universalium

  • Installing building insulation — Due to the variety of building insulation materials available and the various building elements that may require insulation, there are a number of ways of installing building insulation.Where to insulateWhere to insulate depends on where your… …   Wikipedia

  • Framing (construction) — Framing, in construction known as light frame construction, is a building technique based around structural members, usually called studs, which provide a stable frame to which interior and exterior wall coverings are attached, and covered by a… …   Wikipedia

  • painting — /payn ting/, n. 1. a picture or design executed in paints. 2. the act, art, or work of a person who paints. 3. the works of art painted in a particular manner, place, or period: a book on Flemish painting. 4. an instance of covering a surface… …   Universalium

  • Door — For other uses, see Door (disambiguation). A door is a movable structure used to open and close off an entrance, typically consisting of a panel that swings on hinges or that slides or rotates inside of a space. When open, they admit ventilation… …   Wikipedia

  • Polystyrene — For other uses, see Polystyrene (disambiguation). Expanded polystyrene packaging …   Wikipedia

  • DD tank — DD Sherman tank with its flotation screen lowered Service history In service 1944–1950s …   Wikipedia

  • Bridges of the Merritt Parkway — The 69 original bridges of the Merritt Parkway were designed by George L. Dunkelberger. Each bridge had a unique design that represented various 1930s architectural styles, such as Art Deco, Art Moderne, French Renaissance, Gothic, Neoclassicism …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”